Sanders For Sale

Belt size 43” x 85” (2) six inch dust ports 1st head 24 HP 230 2nd head 18 HP 230 Fiest head contact drum Second head combination with finish platen Feed rate 3 to 68 feet per minute Weight 4550 lbs 230 volt 3-phase

SHENG-SHING SDM-25 25" WIDE BELT SANDER1-Head, 24" width cap., rubber covered contact roll, approx. 10 HP motor. -- Abrasive belt size 25" x 48", with air tensioning and electronic abrasive belt tracking. -- 5-1/2" Max. height opening with manual raise & lower; variable feed speed drive. -- Complete with: Magnetic controls & dust outlet.

SHENG-SHING - SDM-15 ...Wide Belt Sander (Open Ended)15" Single Head Wide Belt Sander with open end for up to 30 " capacity. -- Sanding Head: 15" Wide (30" cap. with 2-pass); 8" Helically Grooved Rubber Covered Contact Roll with 7.5 HP Drive. -- Features: 0" - 6" Part thickness cap., 2-speed conveyor feed 12 or 16 FPM; 16" x 48" Abrasive belts with air tensioning, pneumatic abrasive belt tracking.

STATE MODEL B-4 OSCILLATING SPINDLE SANDERSpecifications -- Tilting table design with pedestal floor mount --Table size.20" X 24" -- Table height 40" -- Table tilt 15° up, 45° down -- Spindle speed 1725 RPM -- Vertical oscillation 1-5/8" -- Oscillations/min.90 -- Lubrication...........Oil bath splash -- ÷ ÷Heavy duty 1/2 HP motor Maintenance free 1725 rpm TENV totally enclosed non-vented motor, rated for continuous operation, assuring long term dependable service. -- Safe operator controls Magnetic motor starter with overload protection for save installation. All controls are mounted for operator convenience. -- Operator friendly hand-wheel-tilting Engineered worm gear design allows table to be tilted 15 degrees up and 45 degrees down relative to spindle. Easy-to-read scale allows for accurate tilt determination before engaging locking device. A tapered pin locks the table during horizontal sanding operations. -- Safety features Magnetic motor starter with overload protection, safety labels, well-placed ergonomic controls, 3 throat rings to minimize table-to-spindle clearance, POSITIV-LOK spindles provide safe and quick means of changing spindles. -- Recently Cleaned, checked, electrical contacts cleaned, machine partially disassembled cleaned, re-assembled and tightened, and oil sight glass replacedWeight: 280 lbs.

STATE B-4 OSCILLATING SPINDLE SANDER 1.5 HP Motor with manual switch, (9) spindles from 1/4" DIA to 4" DIA., 1,725 RPM spindle rotation, 20" x 24" table tilts 15° up and 45° down, table height 40". Also includes work light

STEINEMANN OSUS NOVA 160/6 K-FS/NS-OPTIMAT Top and Bottom Calibrating Sander(6) heads consisting in 2 machines, first machine top/bottom opposed head. Secoind machine (4) head with Combi and finishing platenFeatured: -- 2-Head K, (1) top & (1) bottom; both heads directly opposed. for calibrating -- (4) head FS/NS top/bottom first Combi head, second finishing platenSpecifications:First machine Calibrating Sander: -- Top/bottom opposed single head -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on K head 34 M/sec. (6,667 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- 100 HP motor each head. -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine only Second Machine Finishing Sander: -- Top/bottom (2) head each as Combination drum/platen and finishing platen -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on FS head 22 M/sec. (4,330 SFM) -- Cutting speed on NS head 22M/sec. (4,330 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- No motor installed -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine Not included: -- infeed and outfeed conveyor -- Conveyor between the machine -- “all the control wiring goes into a cabinet that is separate on each machine. That is just the wiring for the sensors and solenoids for braking and belt tracking stuff. There are no motor controls with these so there are no starters included. The 2 head comes with (2) 150 HP motors and the 4 head has no motors on it. In order to make these operational you would need a PLC and HMI to run the controls and motor starters and would need to buy motor controls

STEINEMANN Type OSUS NOVA-RSA-190K Sanding Line;Complete with the following major components and features: -- (4) Sets of top & bottom opposed heads (8 heads total). -- Final head is equipped with Platen Sanding (smoothing bars). -- ISS thickness sensor system. -- 1900mm (74 inches) Max. Working Width (sander only, grade line width is a nominal 5 feet). -- CONVEY-KEYSTONE Vacuum Panel Feeder. -- CONVEY-KEYSTONE Canted Roll Infeed Section. -- CONVEY-KEYSTONE Canted Roll Outfeed Section. -- CONVEY-KEYSTONE panel grading system with (3) sort bins; automatic bin selection & discharge. -- STEINEMANN sander controls and control cabinets associated with the sander system. -- (3) Sections of ALLEN-BRADLEY Series 2100 Motor Control Centers (MCCs). (One small section to remain behind for further plant use.)NOTES: &#9679 This is a sanding line designed for manufacturing MDF or Particle Board. Thus, it is built for large capacity. &#9679 Still in place. &#9679 Last in service about 1½ years ago (2021).

SUPERBRUSH 49 BRUSH SANDERSUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications , as well as UV roughing and reclamation projects. Deburring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sander are well suited to shutter sanding, de-glossing and de-stressing. --49" Sanding width, 11" min. part length and 4" max. thickness; 5/8" typical brush dia., 1-1/4" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included. --Rubberized conveyor belt grips and pulls parts through the sander. via 0 -15 FPM variable speed feed system --1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed. --Bristle contact gauge (depth gauge) included. --RPM Gauge displays brush speed, variable 400 - 1,200 RPM. --Hinged dusthood with 4" port, 450 CFM capacity Dust collection recommended. --Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes. --Ball bearings are sealed and permanently lubricated. --Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Gauge). --Option: 7,5 HP motor additional $1,500÷10 HP with electronic inverter and 10 HP motor additional $ 2,500 --SUPERBRUSH 49 Double Brush Sander $37,100

SUPERMAX TOOLS "SUPERBRUSH 24" Single Head Drum SanderMax. width cap. of 24", min. length of 10", min. thickness of 1/32"; brush diameter of 9" - 11", with a variable speed of 400 - 1,200 RPM. -- (1) 4" vacuum dust hood ports; 5 HP - 1,740 RPM brush motor. -- Direct drive 0 - 24 Ft. Per. min. veriable speed conveyer. -- 1-1/2" Dia. Tension rollers, (rubber covered) infeed & outfeet rollers, fully adjustable; reinforced steel conveyor bed with poly conveyor belt. -- Bristle contact gauge (depth gauge). -- Cast stand, zinc-plated steel bed, centerless ground column tubes, ball bearings are sealed and permanently lubricated. -- SUPERBRUSH Applications include, but are not limited to: White wood sanding, de-nibbing, sealer sanding, primer sanding, UV roughing, metal grainding / straight lining, metal de-burring, sanding/polishing solid surface material, scuff sanding, shutter sanding, de-glossing and de-stressing.This SuperBrush 24-Inch single brush sander comes with an 80-grit, dense flatter brush and a bristle contact gauge.

SUPERBRUSH 13" Combination Brush/Drum Sander: -- SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications, as well as UV roughing and reclamation projects. De-burring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sanders are well suited to shutter sanding, de-glossing and de-stressing. It can also be equipped with an optional sanding drum for surface sanding. -- 13" Sanding width, 9" min. part length and 4" max. thickness (varies with drum/brush style), or as thin as 1/32", 6" to 8" Typical Brush diameter; driven by a 1-3/4 HP motor, 3/32" per turn height adjustment, depth gauge included. Dimensions: 35"D x 42"W x 44"H. -- Rubberized conveyor belt grips and pulls parts through the sander. via 0 -10 FPM variable speed feed system. 1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed. Bristle contact gauge (depth gauge) included. -- RPM Gauge displays brush speed, variable 400 - 1,200 RPM. -- Dust Hood: (1) 4″ Port, Hinged At Back, 600 CFM min. recommended. -- Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes. Ball bearings are sealed and permanently lubricated. -- Machine comes with one (1) drum or brush of choice based on application.Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Guage).Shipping Dimensions: (L x W x H): 34-½″ x 45-½″ x 46-½″. Shipping Weight: 300 Lbs (approx.).

SUPERBRUSH 49 x 2 Double Brush Sander, (2) 10 HP Main Motors. -- "SendSmart" automatic control of the infinite-variable feed rate (0 - 15 ft./min.) for the conveyor gives a perfect finish. -- Precisely dimension stock within .010" across width of sander. -- 49" Wide sanding capacity. -- Multiple grit sanding in single pass with double drums. -- Precision-flattened steel conveyor bed reinforced with four steel cross sections for no "flex". -- Self-cooling drum with abrasive Take-Up-Fastners make changing abrasive quick and easy plus keeping abrasive tightly secured to the drum. -- Sand as thick as 12" and as thin as 1/32" with a min. length of 3-1/2". -- Drum ball bearings are sealed and permanently lubricated. -- Electric height adjustment, high speed and adjustable speed. -- Cast stand, zinc-plated steel bed, centerless ground column tubes. -- Shipped assembled, some minimal assembly required. -- Includes: (2) Brushes, Caster Set . -- Dust collection mandatory, requires 1,800 CFM. -- Equipped with: PROSCALE DRO (digital read out).

SUPERBRUSH 24 Brush Sander from SUPERMAX TOOLS:SUPERBRUSH applications include but are not limited to: White wood sanding, de-nibbing, sealer sanding, primer sanding, UV roughing, metal graining/straight lining, metal de-burring, sanding/polishing solid surface material, scuff sanding, shutter sanding, de-glossing and de-stressing.Specifications: -- 24" Sanding width and 11" max. material thickness (height) and min. 1/32" with manual thickness adjustment; 5 HP main motor. -- Rubberized conveyor belt grips and pulls parts through the sander at 0 - 15 FPM. -- 1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed. -- Bristle contact gauge (depth gauge) included. -- RPM Gauge displays brush speed, variable 400 - 1,200 RPM. Machine Structure: -- Cast stand, zinc-plated steel bed, centerless ground column tubes. -- Ball bearings are sealed and permanently lubricated.

SUPERBRUSH 36 Single Head Brush Sander, 5 HP Drive Motor.SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications, as well as UV roughing and reclamation projects. De-burring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sanderr are well suited to shutter sanding, de-glossing and de-stressing.36" Sanding width, 11" min. part length and 4" max. thickness; 5/8" typical brush dia., 1-1/4" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included.Rubberized conveyor belt grips and pulls parts through the sander. via 0 -15 FPM variable speed feed system1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed.Bristle contact gauge (depth gauge) included.RPM Gauge displays brush speed, variable 400 - 1,200 RPM.Hinged dusthood with (2) 4" ports, 1,200 CFM min. capacity Dust collection recommended.Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes.Ball bearings are sealed and permanently lubricated.Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Guage).

SUPERBRUSH 24 x 2 Double Brush Sander.SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications, as well as UV roughing and reclamation projects. De-burring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sanders are well suited to shutter sanding, de-glossing and de-stressing.24" Sanding width, 11" min. part length and 4" max. thickness; 5/8" typical brush dia., 1-1/4" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included.Drive Motor: (2) 7.5 HP MotorsRubberized conveyor belt grips and pulls parts through the sander. via 0 -30 FPM variable speed feed system1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed.Bristle contact gauge (depth gauge) included.RPM Gauge displays brush speed, variable 400 - 1,200 RPM.Hinged Dust Hood with (4), 4″ vacuum ports, 1800 CFM min.Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes.Ball bearings are sealed and permanently lubricated.Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Guage).

SUPERBRUSH 36 x 2 Dual Brush Sander, (2) 7.5 HP Drive Motors.SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications, as well as UV roughing and reclamation projects. De-burring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sanders are well suited to shutter sanding, de-glossing and de-stressing.36" Sanding width, 11" min. part length and 4" max. thickness; 1-1/2" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included. Sanding heads 9-1/2" diameter. (2) 7-1/2 HP main drive motors provide the ability to remove stock, and smooth the material in one pass.Rubberized conveyor belt grips and pulls parts through the sander. via 0 -15 FPM variable speed feed system1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed.Bristle contact gauge (depth gauge) included.RPM Gauge displays brush speed, variable 400 - 1,200 RPM.Hinged Dust Hood with (6) 4" vacuum ports, min. 1,800 CFM capacity Dust collection recommended.Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes.Ball bearings are sealed and permanently lubricated.Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Guage).

SUPERBRUSH 49 Single Brush Sander, 7.5 HP Main Motor.SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications , as well as UV roughing and reclamation projects. Deburring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sander are well suited to shutter sanding, de-glossing and de-stressing.49" Sanding width, 10" min. part length and 11" max. thickness (varies with brush style); 9" - 11" typical brush dia., 1-1/4" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included.Rubberized conveyor belt grips and pulls parts through the sander. via 0 -15 FPM variable speed feed system1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed.Bristle contact gauge (depth gauge) included.RPM Gauge displays brush speed, variable 400 - 1,200 RPM.Hinged Dust Hood with (3) 4" vacuum ports, min. 1,800 CFM capacity Dust collection recommended.Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes.Ball bearings are sealed and permanently lubricated.Includes: (1) Brush and Caster Set

Tidland 470 Sander This system was used in a particle board plant that has been closed around 10 years.

Only 697 hours, taken from service (2) top heads - one orbit, one brush (1) 3HP main orbit motor (1) 3HP feed motor (1) 1HP brush motor (1) 1HP oscillation motor 460V Max. stock width 36" Max. thickness 6" 32-38" variable passline height 2,000 CFM @ 5,000 FPM exhaust air requirements

TimeSaver Mdl 325-2 36" Wide Belt Sander S/N 7887

Timesaver Mdl 337-6 36" Belt Sander S/N 18395