• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
90 Results Found for Shaper Viewing 1 - 20 of 90 results
STANDARD LISTINGS
B.M.TEN Shaper with 1-1/4" Interchangeable spindle, 7.5 HP motor. -- 35-1/2" x 43" fixed table. -- Vertical spindle travel is 7-3/4" -- 5-5/16" cap. under the nut. -- (5) spindle speeds 2,800 - 4,500 - 6,000 - 8,000 & 10,000 RPM -- Complete with: 3-Roller Power Feeder.
Equipment Location:PACIFIC NORTHWEST, AL
EX-FACTORY INC.
704-841-2001
BACCI TTFI Miter Door Cut, Drill and ShapeCabinet mitre door machine, cutting boring and moulding machine, designed for 45 degree mitre frame door production, with each cycle the parts are trimmed drilled and finger jointed,Features: -- The TTF1, single sided cutting-boring-moulding machine is equipped with: -- Hydraulic control of table stroke. -- Ball bushing and ground and hardened guides for the table movement. -- High precison cutterholder spindle moulding unit with automatic return. -- PLC allows any combination of the cutting boring moulding operations, designed for 45 degree mitre frame door production, with each cycle the parts are trimmed drilled and finger jointed, a complete joint is produced with each cycle.Technical Data: -- Dia. of saw blade 400 mm, 3 HP motor, -- Boring depth 60 mm, -- (2) Shaping units (1 clockwise and 1 counter clockwise), 35 mm shaft dia., 8,000 RPM spindle speed, max. size of tools 160 mm dia.. x 120 mm height;, 7.5HP motor.
Equipment Location:EASTERN CDN
Torry Hiddema
800-374-5009 ext:371
BALESTRINI MINI C 2500 DOUBLE SIDED TEMPLATE PROFILE SHAPER -- (2) Offset shaping heads with 10 HP (7.5 kW), 230/460 volt three phase drives. (1 each side) -- Maximum reciprocating length 98" (2500 mm). -- Maximum height 7" (180 mm). -- Maximum width between spindles 8", and shaping heads are staggered for full end rounding. -- 1¼” diameter work arbors with 7″ under the nut capacity, and Spindle speed of 8400 RPM -- Hydraulic stroke of 9-3/4″ wide x 110″ long tee slotted work table, with feed speeds of 3 - 49 feet per minute (1-15 m/min.) powered by 3HP, 230/460 volt three phase hydraulic pump -- Overhead beam clamp bar with (6) adjustable clamps. -- Push button operator control station. -- Includes (2) Oertli 4″ X 6″ spiral insert cutter-heads. -- Very clean Mini C 2500, Owner has recently replaced several air solenoids and installed several piston rebuild kits.
Equipment Location:MIDWEST
Torry Hiddema
800-374-5009 ext:371
BALESTRINI C 70 Double Sided Feed Through Shaper;Profiles various chair, table and casegood components from a prepared template. The feed through system allows curved or extremely long parts to be shaped with little or no limitation. Equipped with: -- (2) Vertical shaper spindles, 7.5 HP motor each; 30 mm dia. spindles, 8,000 RPM cutter rotation. -- Reversing rotation by switch for climb cut or conventional cut. Specifications: -- Max. working width 358 mm (14-1/8"), max. working height 118 mm (4-5/8"), min. working length 240 mm (9-1/2"); max. size of cutter blocks 90 mm x 120 mm and up to 3/8" vertical adjustment of heads. -- Part on template block is being shaped by running between spring loaded spindles with copy bearings following the template pattern. -- 1 HP variable feed motor 3 - 26 FPM, hand crank adjustable horizontal rubber infeed & outfeed holddown rollers. -- Machine has (2) 120 mm diameter dust outlets. -- Machine dimensions: 53" x 49" x 43" Machine weight: 2,310 lbs.
Equipment Location:NORTHEAST
Torry Hiddema
800-374-5009 ext:371
BALESTRINI C 70 Double sided Shaper -- Automatic feed through shaper profiles various chair, table and casegood components from a prepared template. The feed through system allows curved or extremely long parts to be shaped with little or no limitation. Equipped with: -- (2) Vertical shaper spindles, 7.5 HP motor each; 30 mm dia. spindles, 8,000 RPM cutter rotation; reversing rotation by switch for climb cut or conventional cut. Specifications: -- Max. working width 358 mm (14-1/8"), max. working height 118 mm (4-5/8"), min. working length 240 mm (9-1/2"); max. size of cutter blocks 90 mm x 120 mm and up to 3/8" vertical adjustment of heads. - Part on template block is being shaped by running between spring loaded spindles with copy bearings following the template pattern. -- 1 HP variable feed motor 3 - 26 FPM, hand crank adjustable horizontal rubber infeed & outfeed holddown rollers. -- Machine has (2) 120 mm diameter dust outlets. -- Machine dimensions: 53" x 49" x 43" Machine weight: 2,310 lbs.
Equipment Location:EASTERN CDN
Torry Hiddema
800-374-5009 ext:371
BERMAQ - AG-108, ...Automatic Shaper.For 1-piece raised panels in wood or MDF; transforms round mouldings into right-angles; pneumatically operated cycles with adjustable electromechanical devices. -- Equipped with: Blade profiled with the same pattern as the miller; tool carries out an automatic cycle of progressive cuts. -- Working measurements of 1,000 x 700 x 30 mm. -- Air pressure of 6 Bar (84 PSI), max. air consumption of 220 LPM; approx. weight of 640 kg (1,420 Lbs); 220 V, 50/60 Hz. -- Foot activated operation, incl. emergency stop.
Equipment Location:MIDWEST
Torry Hiddema
800-374-5009 ext:371
CAM-WOOD CS-2145DR Tenoner with Dowel DrillTenoning/Coping machine for straight or miter material. Great machine for miter door production or stile and rail stock. -- Equipped with:6" High stackable spindle by pneumatic up & down with 3 different stops; easily and accurately setup for each cutter position.Drill heads for dowel hole at each end.One shaper head at each side of the table.Table moves from right to left by variable speed Pneumatic-Hydraulic power to achieve the fully cutting power.Twin table moves in and out separated for tongue and groove, end match application.Twin heavy-duty pneumatic pistons hold down the work pieces tightly to the table during the cutting process. -- Features:Rigid construction on the heavy sheet metal frame, cast iron table & base for durability usage.Heavy duty industrial motor is suitable for heavy duty cutting under full load.Linear guide rails and bearings let the operator moving the table smoothly.Cast iron fence locks in the table groove to finish 45° cut easily.Fully automatic cycle function, just place the material against the stops, machine will automatic clamp, move in for shaping/tenoning, come out and release the hold down.
Equipment Location:WEST COAST
Torry Hiddema
800-374-5009 ext:371
CAM-WOOD CS-2145M TenonerTenoning/Coping machine for straight or miter material. Great machine for miter door production or stile and rail stock. -- Equipped with:6" High stackable spindle by pneumatic up & down with 3 different stops; easily and accurately setup for each cutter position.One shaper head at each side of the table.Table moves from right to left by variable speed Pneumatic-Hydraulic power to achieve the fully cutting power.Twin table moves in and out separated for tongue and groove, end match application.Twin heavy-duty pneumatic pistons hold down the work pieces tightly to the table during the cutting process. -- Features:Rigid construction on the heavy sheet metal frame, cast iron table & base for durability usage.Heavy duty industrial motor is suitable for heavy duty cutting under full load.Linear guide rails and bearings let the operator moving the table smoothly.Cast iron fence locks in the table groove to finish 45° cut easily.Fully automatic cycle function, just place the material against the stops, machine will automatic clamp, move in for shaping/tenoning, come out and release the hold down.
Equipment Location:WEST COAST
Torry Hiddema
800-374-5009 ext:371
CAM-WOOD CS-40PAAU Automatic ShaperManufactures cabinet raised panel doors with (1) operator. -- Equipped with:10 HP Main motor drives 1-1/4" Dia. x 6" high stackable multi-cutter spindle @ 9,000 RPM to mill stile, rails, and raised panel profiles.Stackable cutter spindle with (3) pneumatic stop indexing significantly reduces setup time as each position is preset; the change from one cutter to another is achieved via a select switch for each operation. -- Features:Table movements from left to right are hydraulically powered for powerful cutting and cutting speed variability. Table movements in and out are pneumatically powered to assure that the template is followed sensitively and the shape is copied correctly. 40" door maximum.
Equipment Location:WEST COAST
Torry Hiddema
800-374-5009 ext:371
CAM-WOOD SP-30 Fixed Spindle ShaperA Shaper with plenty of cast iron... a solid piece of machinery!Features & Specifications: -- 3 HP Motor with reversing switch. -- Interchangeable spindle as standard with a 1" & 3/4" spindles. -- Spindle with 4" under nut. -- (2) Spindle speeds of 8,000 & 10,000 RPM. -- Large 30" x 28" cast iron precision ground table. -- 7" Max. table ring. -- Easily locked spindle for cutter change. -- Micro-adjustable back fence with material spring holddowns. -- Includes Miter gauge, cutterhead guard assembly, and operators manual.NOTE: Available in 3-Phase and 1-Phase electric.
Equipment Location:WEST COAST
Torry Hiddema
800-374-5009 ext:371
CANTEK Model SS-512M Single Spindle Shaper with 5 HP - 3-Phase motor. -- 31-1/2" x 39" fixed table with dovetail slot. -- 1-1/4" dia. spindle with a spindle stroke of 5-1/2", 5 MT receiver, and 4-3/4" cap. under the nut. -- (4) Spindle speeds: 3,000, 6,000, 7,500 & 10,000 RPM.Complete with: Spindle reversing switch, Miter Gauge, Micro-adjustable fence 6" x 43", Thermal overload protection.
Equipment Location:WESTERN CDN
Torry Hiddema
800-374-5009 ext:371
CANTEK SS-512TSB Tilting Spindle and Sliding Table Shaper:7.5 HP - 3-Phase motor, overall table dimensions 31.50" x 39.40", sliding table 10.25" x 39.40". -- Spindle stroke 7"; 1-1/4" dia. spindle with 5 MT receiver and 4-3/4" cap. under the nut. Spindle tilts -5° & +45°. -- (5) Spindle speeds: 3,000, 4,000, 6,000, 8,000 & 10,000 RPM.Complete with: Spindle reversing switch, micro-adjustable fence 6" x 43", thermal overload protection and dust hood.
Equipment Location:PACIFIC NORTHWEST
Torry Hiddema
800-374-5009 ext:371
CASADEI F-114 Shaper with 5 HP Spindle motor. -- 1-1/4" dia. spindle, 7" spindle length, 8-1/2" vertical travel, manual raise/lower of spindle, numerical readout display for spindle setting. -- (4) speeds at 2,900 - 4,400 - 6,000 & 8,000 RPM, electro-magnetic spindle brake. -- 43" x 28" table size, adjustable fence (360ø rotatable) with (3) micro-metric fine adjustments. -- Complete with: Overload protection and electric spindle lock.
Equipment Location:WESTERN CDN
Torry Hiddema
800-374-5009 ext:371
CASADEI F-114 Shaper with 5 HP Spindle motor and Power Feeder. -- 1-1/4" dia. spindle, 7" spindle length, 8-1/2" vertical travel, manual raise/lower of spindle, numerical readout display for spindle setting. -- (4) speeds at 2,900 - 4,400 - 6,000 & 8,000 RPM, electro-magnetic spindle brake. -- 43" x 28" table size, adjustable fence (360ø rotatable) with (3) micro-metric fine adjustments. -- Complete with: Overload protection, electric spindle lock, and Power Feeder
Equipment Location:WESTERN CDN
Torry Hiddema
800-374-5009 ext:371
CASADEI F-114 Shaper with 8 HP Spindle motor and MAGGI Power Feeder. -- 1-1/4" dia. spindle, 7" spindle length, 8-1/2" vertical travel, manual raise/lower of spindle. -- (4) speeds at 2,900 - 4,400 - 6,000 & 8,000 RPM, electro-magnetic spindle brake. -- 43" x 28" table size, adjustable fence with micro-metric fine adjustments. -- Complete with: Overload protection, electric spindle lock, and MAGGI 4-Roll Power Feeder.
Equipment Location:MIDWEST
Torry Hiddema
800-374-5009 ext:371
CASADEI F-114 Shaper with 8 HP Spindle motor and STEFF Power Feeder. -- 1-1/4" dia. spindle, 7" spindle length, 8-1/2" vertical travel, manual raise/lower of spindle. -- (4) speeds at 2,900 - 4,400 - 6,000 & 8,000 RPM, electro-magnetic spindle brake. -- 43" x 28" table size, adjustable fence with micro-metric fine adjustments. -- Complete with: Overload protection, electric spindle lock, and STEFF 3-Roll Power Feeder.
Equipment Location:MIDWEST
Torry Hiddema
800-374-5009 ext:371
CASADEI Model F 115 Sliding Table Shaper with Maggi Steff Power Feeder. -- 9 HP motor, 1-1/4" dia. spindle, 7" spindle length, 8-1/2" travel up/down, (4) spindle speeds at 2,900 / 4,400 / 6,000 & 8,000 RPM. -- Equipped with: Reverse switch; adjustable fence (360ø rotatable) with (3) micro-metric fine adjustmentss; sliding table 43" x 28" in size. -- Complete with: Maggi Steff 2048 Power Feeder.
Equipment Location:WEST COAST, AL
EX-FACTORY INC.
704-841-2001
CASADEI F 115 Spindle Shaper; Single Spindle Shaper with 11 HP Motor, 1-1/2" dia. spindle. -- (5) Spindle Speed 2,900 - 4,400 - 6,000 - 8,000 &10,000 RPM. 7" Under nut, adjustable spindle height of 8-1/2". -- Features hand wheel for micrometric adjustments, fence to both sides of cutter head with micro adjustments, -- 43.3" x 29-1/2" Polished steel table with 13" cutter head opening. Complete with: -- Automatic spindle brake, spindle locking, motor reversing switch. -- Shaving hood, shaper fence guard; magnetic starter. -- Power Feeder available for additional charge.
Equipment Location:WESTERN CDN
Torry Hiddema
800-374-5009 ext:371
The FAS is a dedicated milling machine with inclinable heads for machining the corner of chair seats. -- Specifications: -- (2) Heads with 5.5 HP motor and 40 mm spindle shaft. -- Maximum cutter size 150 mm (5.9"). -- Tilting of milling units -20°/ +45° in horizontal plane. -- Fixed left hand column to support head unit. -- Maximum working height 200 mm (7.8").
Equipment Location:EASTERN CDN
Torry Hiddema
800-374-5009 ext:371
1-3/4" Spindle dia., 7.5 HP motor, cast iron table. -- Includes: A & B 4-Speed belt driven Power Feeder with SCR feed control.
Equipment Location:PACIFIC NORTHWEST
Torry Hiddema
800-374-5009 ext:371