Tennoners For Sale

Filtering

Reset All 

thru
 Used     New
Viewing Page 1 of 2
40 Results Found
Sort By 
STANDARD LISTINGS
1998 Bacci TSG 2T  Tennoner
$14,250

BACCI TSG 2T Round End Tenoner with twin positioning tables with a traversing single cutter head design. Movement of cutter head is by mechanical cam actuation on bearing slides. -- General Data: 4 HP - 5,700 RPM belt driven head, cutterhead traversing motor 1 HP. Tables alternate into the cutting cycle for continuous operation, each table is laterally positioned with air cylinders; straight, simple or compound angles are easily adjusted with tables: 0° - 15° up, 0° - 30° down and 0° - 20° bevel, (1) table with overhead adjustable pneumatic holddown. -- Capacity: Tenon depth: 3/8" to 1-3/4" (10 to 45 mm) with special tooling 1/4" to 3-1/2" (6 to 90 mm), max. tenon width: 1-5/8" (42 mm), and max. tenon length: 4-1/2" (115 mm plus both radii). Production rates approx. (600 - 840) pieces/Hr. -- Complete with: Push button controls on front of machine. Tranformer for 600 volts operation. -- Note: See MO category for female Mortisers.

Louis Sicotte
800-374-5009 ext:329
Call

2000 Bacci TSG 2T  Tennoner
$12,700

BACCI TSG 2T Round End Tenoner with twin positioning tables With a traversing single cutter head design. Movement of cutter head is by mechanical cam actuation on bearing slides. General Data: -- 4 HP - 5,700 RPM belt driven head, cutterhead traversing motor 1 HP. -- Tables alternate into the cutting cycle for continuous operation, each table is laterally positioned with air cylinders; straight, simple or compound angles are easily adjusted with tables: 0° - 15° up, 0° - 30° down and 0° - 20° bevel. --(1) Table with overhead adjustable pneumatic holddown. Capacity: -- Tenon depth: 3/8" to 1-3/4" (10 to 45 mm) with special tooling 1/4" to 3-1/2" (6 to 90 mm). Max. tenon width: 1-5/8" (42 mm), and max. tenon length: 4-1/2" (115 mm plus both radii). -- Production rates approx. (600 - 840) pieces/Hr Complete with: -- Push button controls on front of machine. -- Transformer for 600 Volts

Louis Sicotte
800-374-5009 ext:329
Call

Balestrini PICO  Tennoner
$14,950

BALESTRINI PICO Round End TenonerProduces straight, simple or compound angle round end tenons, for blind tenons. Left & right twin tables allow for (1) part to be tenoned while other table is unloaded and loaded, approx. (600 to 700) per hour.Specifications: -- 14" x 9" (355 x 230 mm) Tables tilt 0° - 20°, table fence swivels up to 45°, 4-3/4" (120 mm) vertical table adjustment, (2) vertical pneumatic hold downs. -- 4 HP Cutter block motor, 1 HP cutter block rotation motor, 9,000 RPM spindle speed, movement of table with 0.75 HP motor. -- Capacity: 3-15/16" (100 mm) Max. tenon length, 1-3/16" (30 mm) max. thickness, and 1-31/32" (50 mm) max. depth; can also produce round end dowels. -- Hourly production rate of (600 - 700) tenons.

Louis Sicotte
800-374-5009 ext:329
Call

2005 Balestrini PICO MD/2  Tennoner
$23,500

BALESTRINI PICO MD CNC Round End Tenoner/Mortiser -- Great compact CNC for MITERED cabinet door and furniture parts; equipped with a tenoning block and a slot mortiser, and scribing function to achieve a chip free cut.Technical Specifications: -- Max. depth of mortise/tenon 50 mm (1.97"); Max. thickness of mortise/tenon 38 mm (1.5") -- Max. frame width 120 mm (4.72");÷Max. thickness 40 mm (1.57"). -- Tenon/Cut-off motor 4.1 KW (5.5 HP); motor speeds 9,000 & 12,000 RPM. -- Mortising motor 2 KW (2.7 HP); motor speeds 9,000/12,000 &18,000 RPM. -- (2) Adjustable pneumatic lateral clamps; -- (2) Dust collection points for 100 mm (4") pipe. -- Integrated control cabinet with screen and front mounted controls.Touch screen controller with 40 Gb hard disk storage; Simple programming with pre-installed macro's; Offset function allows easy reset of programming to obtain a tighter or looser fit tolerance as needed.

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET DADO  Tennoner
$54,650

CAM-WOOD SET DADO Double End Trim & Dado (Angle gain)Trim Saw and Dado Cutter for Door Jamb and CasingSpecifications: -- Working Length 450 ~ 2650 mm -- Working Width 30 ~ 185 mm -- Working Thickness 9 ~ 35 mm -- Holddown CylinderEquipped with: -- (2) Sets Trim Saw Heads, 3 HP motor each; Spindle 1" Dia., Spindle Speed 1800 RPM; Saw can tilt and swivel (from the base) 0 - 45° -- (2) Shaper Heads, 3 HP motor each; Spindle 1" Dia., Spindel Speed 3600 RPM, Cutting Angle adjustment 0 to 45°. -- Feed Magazine 24” Height Magazine -- Feed Air Cylinder with Stops -- (4) Dust Hood units, each 4” opening -- Cycle time 10 to 15 Pcs/Minute

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET DOOR STOP  Tennoner
$41,250

CAM-WOOD SET DOOR STOP Double End Trimming Saw -- Double end trimming for straight or 45° cut with upper feed magazineSpecifications: -- Working Length 450 ~ 2650 mm (17.7" - 104.3") -- Working Width 30 ~ 185 mm ( 1.18"- 7.28") -- Working Thickness 9 ~ 35 mm ( .35" - 1.38") -- (2) Hold Down Cylinder -- (2) Trim Saw Heads 3 HP, Trim Saw Head Spindle 1 Dia., Trim Saw Head Speed 1800 rpm -- Cutting Angle adjustment 0 to 45 Degrees -- Feed Magazine 24” Height – Feed system with air Cylinder with Stops -- Dust Hood 4” x 2 Units

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-44DET  Tennoner
$82,900

CAM-WOOD SET-44DET Double End Tenoner for Click Lock Flooring -- (4) heads each side as Top Scoring, Bottom Trim Saw, Jump shaper, Shaper -- Designed for click lock System application Specifications: -- Maximum working thickness 2 1/4" -- Maximum working length 48" (optional for 96") -- Minimum working length: 9" -- (2) Saw motor 3 HP -- (4) shaper motor 7.5 HP with dual speed 3,600 and 7,200 RPM, arbor 40 mm diameter, spindle tilting 0-90 degrees -- Feed speed 20 to 82 FPM, drive motor 2 HP -- Motorized opening with 1 HP motor -- Control with colour touch screenAvailable option: -- Hopper feed magazine -- Sound enclosure

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-46TS  Tennoner
$38,990

CAM-WOOD SET-46TS 6 Heads 48" Double End Tenoner: -- Soring, trimming and shapingCapacity: -- Max. 48" working capacity, min. 12"; max. 4" opening, 24" load area in front of hold-downs. -- Motorized opening with LED indicator; -- Single-post machine, single "dual-track" base, right side fixed, left side movable.Each side equipped -- Front of post: Bottom scoring unit, 2 HP - 3,600 RPM motor, 1" dia. arbor & up to 10" blade; -- Top trim head, 3 HP - 3,600 RPM motor, 1" dia. arbor for up to 10" blade; -- Back of post: Vertical shaping head, 5 HP - 7,200 RPM motor, 5-7/8" (150 mm) long & 1" dia. arbor, 8" max. dia. cutter-head. -- Variable feed speed from 12 - 52 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads and dogs at 6" center, --Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Cross transfer system with transfer line 4' X 8' transfer table with rollers (additional $29,600) -- Hopper feed magazine (additional $3,990) -- Pneumatic jump control on scoring or shaping unit -- Same machine with 8' opening

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-46TS-SHJC  Tennoner
$48,990

CAM-WOOD SET-46TS-SHJC 6 Heads 48" Double End Tenoner: -- Double end tenoner with Scoring, Hogging and Jump copingCapacity: -- Max. 48" working capacity, min. 12"; max. 4" opening, 24" load area in front of hold-downs. -- Motorized opening with LED indicator; -- Single-post machine, single "dual-track" base, right side fixed, left side movable.Each side equipped -- Front of post: Bottom scoring unit, 2 HP - 3,600 RPM motor, 1" dia. arbor & up to 10" blade; -- Top Hoging/triming head, 5 HP - 3,600 RPM motor, 1" dia. arbor for up to 10" blade; -- Back of post: Vertical Jump shaping head, 5 HP - 7,200 RPM motor, 6" to 8" tool capacity & 1" dia. arbor, -- Variable feed speed from 12 - 52 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads and dogs at 6" center, --Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Hopper feed magazine (additional $3,990) -- Pneumatic jump control on scoring or shaping unit -- Extended infeed 42" ( additional$4,600) -- Sound enclosure ( additional $ 6,900)

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-46TS-SHJC  Tennoner
$54,990

CAM-WOOD SET-46TS-SHJC 6 Heads 96" Double End Tenoner: -- 96" Double end tenoner with Scoring, Hogging and Jump copingCapacity: -- Max. 96" working capacity, min. 12"; max. 4" opening, 24" load area in front of hold-downs. -- Motorized opening with LED indicator; -- Single-post machine, single "dual-track" base, right side fixed, left side movable.Each side equipped -- Front of post: Bottom scoring unit, 2 HP - 3,600 RPM motor, 1" dia. arbor & up to 10" blade; -- Top Hoging/triming head, 5 HP - 3,600 RPM motor, 1" dia. arbor for up to 10" blade; -- Back of post: Vertical Jump shaping head, 5 HP - 7,200 RPM motor, 6" to 8" tool capacity & 1" dia. arbor, -- Variable feed speed from 12 - 52 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads and dogs at 6" center, --Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Hopper feed magazine (additional $3,990) -- Extended infeed 42" ( additional$4,600) -- Sound enclosure ( additional $ 6,900) -- Auto transfer line (4' X 8') with transfer table ( additional$ 29,600)

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-52SAT  Tennoner
$17,850

CAM-WOOD SET-52SAT 6-Head Double End Tenoner (Not Feed Through)Capacity: -- Length of cut: 12" to 60" (opening). -- Max. width of cut: 24" (cross cut). -- Max. clamping thickness: 4-1/2". -- Saw blade dia. 8" to 12"; saw arbor dia. 1"; saw blade speed 3,400 RPM; saw head swivels 180 degrees. -- Moulder (Shaper) spindle: 1" Dia. x 5" long; spindle speed 6,000 RPM; spindle swivels 180 degrees. -- Vertical travel: 17" vertical. -- Carriage (table) travel (front/back): 24".Equipped with: -- Saw motors: (4), each 2 HP motors (1 top & bottom each side). -- Shaper spindles: (2), each 2 HP motors (1 each side). -- Out Feed Conveyor drive: 1 HP motor (not this model!). -- Powered length setting: 1/2 HP motor (machine opening).Features: -- With the double end miter saw set-up, you can cut-off stock faster or consider a double end miter saw combined with moulding (shaper) head. It lets you cut and machine stock and moulding pattern in a single feed, saves time, space and cost. -- Air-operated vertical clamps hold sticks firmly in place. After the work piece is clamped, table start to feed, performs trimming and shaping operations. -- Trim saw allows to cut stock accurately with a clean cut. -- Moulding (Shaper) spindle mounted at the rear of saw head enables the machine to perform edge moulding after stock is cut off. -- The entire cutting cycle, cut-off, shaping/tenon or mortise is automatically operated in a single pass of stock feeding. -- The material Clamping table travels on a precision linear motion guide for stability. -- The table traverse is motorized, ensuring very stable, smooth workpiece feeding. -- Material transport thru machine powered by variable speed inverter drive for 10 to 20 Sec per cycle -- Variable feed speed permits proper feed selection for hard or soft wood materials. -- Large hand-wheel to adjust depth of cut. -- All controls are grouped in a control panel. -- Industrial motors for optimal cutting results.Machine Stations: -- 1: Top & Bottom Trim Saws powered by (4) 2 HP saw arbor motors for trimming to length. -- 2: Shaper spindles powered by (2) 2 HP spindle motors for applying tenons and grooves. -- Floor space requirement: 94" X 40" X 54" high. -- Cycle time: 10 to 20 Sec per cycle.Available option at additional cost: -- Auto Outfeed device -- Return conveyor

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-5SA  Tennoner
$14,600

CAM-WOOD SET-5SA Double End Trim Saw (Tenoner) Capacity: -- Length of cut: 12" to 60" -- Max. width of cut: 24" -- Max. clamping thickness: 4-1/2" -- Saw blade dia. 8" to 12"; saw arbor dia. 1"; saw blade speed 3,400 RPM; saw head swivels 360 degrees. -- Moulder (Shaper) spindle: 1" Dia. x 5" long; spindle speed 6,000 RPM; spindle swivels 360 degrees. -- Vertical travel: 17" -- Carriage cross travel: 24"Equipped with: -- Saw motors: (2) each 2 HP motors -- Moulder spindles: (2) each 2 HP motors -- Out Feed Conveyor drive: 1 HP motor -- Powered length setting: 1/2 HPFeatures: -- With the double end miter saw set-up, you can do cut-off stock faster or consider a double end miter saw combined with moulding head. It lets you cut off stock and moulding pattern in a single feed, that saves time, space, and cost. -- Air-operated clamp comes down holding sticks firmly in place. After work piece is clamped, table start to feed, performs trimming and shaping operations. -- Trim saw allows to cut stock accurately with a clean cut. -- Moulding (Shaper) spindle mounted at the rear of saw head enables the machine to perform edge moulding after stock is cut off. -- The entire cutting cycle, cut-off, shaping/tenon or mortise is automatically operated at single pass of stock feeding. -- The table travels on a precision linear motion guide for stability. -- The table traverse is driven by power system, ensuring very stable, smooth workpiece feeding. -- Variable feed speed permits proper feed selection for hard or soft wood materials. -- Big hand wheel adjusts depth of cut. -- All controls are grouped in a control panel. -- Industrial motors for optimal cutting results. -- Material transport thru machine powered by variable speed inverter drive for 10 to 20 seconds per cycle Machine Stations: -- 1: Trim saws powered by (2) 2 HP saw arbor motors for trimming to length. -- 2: Shaper spindles powered by (2) 2 HP spindle motors for applying tenons and grooves. -- Floor space requirement: 94" X 40" X 54" high -- Cycle time: 10 to 20 second per cycleAvailable option at additional cost: -- Auto Outfeed device -- Return conveyor

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-810SCCWW  Tennoner
$105,900

CAM-WOOD SET-810SCCWW Double End Tenoner With SandingFeatures: -- The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 20~66 FPM. -- Suitable for mass production of woodworking factory for processing of double end cutting, tenoning, grooving, moulding, and sanding. -- In addition to the double end cutting, all the settings and other processing can also be executed with high accuracy. -- Since the machine is so versatile, we believe it will be one of the most satisfactory machines for bulk production lumber-processing factories. -- The specially designed numeric controller allows quick setting of length sizes for tolerance within 0.004". -- The numeric counting system provides highly accurate settings, and a special memory retains all settings, even if there is a power failure. -- Variable speed, through feed, wide rubber pad, spring-loaded dots conveyor for the best finish selections. -- Heavy-duty powered pressure rolls at top of wide width conveyor to hold the material tight to prevent sliding during the cutting and sanding process. -- Shaper head can be moved up & down, forward & backward. -- Equipped with industrial motor for full power cutting and sanding capacity. -- Two sanding heads can use brush, flap wheel or profile disc for fine finish with one pass. -- Trim saws and sanding heads can be tilted for different angular setup.Specifications: -- Max. Working Size: Thickness 4", Length 96", -- Miter Saw Blade 12" x 1" Dia. -- Grooving Saw Blade 8" x 1" Dia. -- Shaper Cutter 6" ~ 10" x 1" Dia. -- Feed Speed 20' ~ 66' Variable, motor 3 PH, 220/440 V -- tilting Trim Saw 5 HP x 2 -- Jump shaper 10 HP x 2 -- Jump Shaper 10 HP x 2 -- Tilting Sanding 3 HP x 2 -- Tilting Sanding 3 HP X 2 -- Width Setting 1 HP x 1Available Options: -- Sound enclosure -- larger motors -- extended infeedFloor space requirement: 14' X 14' X 5'Weight: 16,500 lbs

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-812SCCWW  Tennoner
$158,900

CAM-WOOD SET-812 SCCWW, Double End Tenoner with Sanding -- 12 heads double end tenonerFeatures: -- The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 20~75 FPM. -- Suitable for mass production of woodworking factory for processing of double end cutting, tenoning, grooving, moulding, and sanding. -- In addition to the double end cutting, all the settings and other processing can also be executed with high accuracy. -- Since the machine is so versatile, we believe it will be one of the most satisfactory machines for bulk production lumber-processing factories. -- The specially designed numeric controller allows quick setting of length sizes for tolerance within 0.004". -- The numeric control system provides highly accurate settings, and a special memory retains all settings, even if there is a power failure. -- Variable speed, through feed, wide rubber pad, spring-loaded dots conveyor for the best finish selections. -- Heavy-duty powered pressure rolls at top of wide width conveyor to hold the material tight to prevent sliding during the cutting and sanding process. -- Shaper head can be moved up & down, forward & backward. -- Equipped with industrial motor for full power cutting and sanding capacity. -- Two sanding heads can use brush, flap wheel or profile disc for fine finish with one pass. -- Trim saws and sanding heads can be tilted for different angular setup. -- Heavy cast iron base for durability usage.SPECIFICATIONS: -- Thickness: ½"to 5" -- Length: 10"to 96" -- Miter Saw Blade: 10" x 1" Dia. -- Grooving Saw Blade: 8" x 1" Dia. -- Shaper Cutter: 6" ~ 10" x 1" Dia. -- Feed Speed:20' ~ 75' Variable ,Motor 3 PH, 220/440 V -- Trim Saw 3HP x 2 -- Jump Hogging Saw 15 HP x 2 -- Shaper 10HP x 2 -- Jump Shaper 10 HP x 2 -- Belt Sanding 3 HP x 2 -- Brush Sanding 3HP x 2 -- Feeding 3 HP x 1 -- Width Setting 1HP x 1 Option: -- Sound enclosure $ 7800

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-86DET  Tennoner
$75,900

CAM-WOOD SET-86DET SSC 6 Heads Double End Tenoner -- Suitable for mass production of woodworking task for double end cutting, tenoning, grooving, profiling and sanding -- Saw, Shaper, Shaper: Total 3 stations at both sides. -- It is a powerful machine great for heavy-duty production.Capacity: -- The specially designed numeric controller allows quick setting of sizes, for the tolerance within 0.004”. -- Variable speed, through feed, wide rubber pad, spring loaded dogs at 8" center conveyor for the best finish selections. -- Heavy-duty pressure rolls at top of wide width conveyor to hold the material tight to prevent sliding during the cutting process. -- Shaper head can be moved up & down, forward & backward. -- Max. 96" working capacity, min. 12"; max. 3 1/8" opening, 24" load area in front of hold-downs. -- .The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 20~82 FPM. -- Motorized opening with LED indicator.Each side equipped -- Scoring saw unit , 2 HP - 3,600 RPM motor, 1" dia. arbor & up to 8" blade -- Trim saw tiltable unit, 3 HP , 3,600 RPM motor, 1" arbor and up to 10" blade. -- Shape/coping head unit. , 7.5 HP - 4,500-7,000 RPM motor, 1 1/4" or 40 mm dia. arbor for up to 8" cutter head. -- Variable feed speed from 20 - 66 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads and dogs at 6" center. -- Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Hopper feed magazine -- Pneumatic jump control on scoring or shaping unit. -- Sound enclosure -- Electric motor brake -- Jump shaper -- Tilting shaperFloor space : 14' X 9' X 5", weight 10,500 lbs

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-86TS  Tennoner
$44,990

CAM-WOOD SET-86TS Double End Tenoner 6 HeadsCapacity & Style: -- Max. 98" working capacity, min. 12"; max. 4" opening, 24" load area in front of hold-downs. -- Single-post machine, single "dual-track" base, right side fixed, left side movable. -- Motorized opening with LED indicator.Each side equipped with: -- Front of post: Bottom scoring unit, 2 HP - 3,600 RPM motor, 1" dia. arbor & up to 10" blade. -- Top trim head, 3 HP - 3,600 RPM motor, 1" dia. arbor for up to 10" blade. -- Back of post: Vertical shaping head, 5 HP - 7,200 RPM motor, 5-7/8" (150 mm) long & 1" dia. arbor, 8" max. dia. cutter-head. -- Variable feed speed from 12 - 52 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads and dogs at 6" center. -- Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Cross transfer system with transfer line 4' X 8' transfer table with rollers (additional $29,600). -- Hopper feed magazine (additional $3,990). -- Pneumatic jump control on scoring or shaping unit. -- Sound enclosure -- Electric motor brake -- Central supportNote: Pictures are showing the machine with several options included

Louis Sicotte
800-374-5009 ext:329
Call

2021 Cam-Wood SET-88DET-SHJCJC  Tennoner
$101,900

CAM-WOOD SET-88DET-SHJCJC 8 Heads 96" Double End Tenoner -- Suitable for mass production of woodworking task for double end cutting, tenoning, grooving, profiling and sanding -- Scoring, Hogger/Saw, Jump Shaper, Jump Shaper: Total 4 stations at both sides. -- It is a powerful machine great for heavy-duty production.Capacity: -- The specially designed numeric controller allows quick setting of sizes, for the tolerance within 0.004”. -- Variable speed, through feed, wide rubber pad, spring loaded dogs at 8" center conveyor for the best finish selections. -- Heavy-duty pressure rolls at top of wide width conveyor to hold the material tight to prevent sliding during the cutting process. -- Shaper head can be moved up & down, forward & backward. -- Max. 96" working capacity, min. 12"; max. 3 1/8" opening, 24" load area in front of hold-downs. -- .The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 20~66 FPM. -- Motorized opening with LED indicator.Each side equipped -- Top Scoring saw unit , 2 HP - 3,600 RPM motor, 1" dia. arbor & up to 8" blade -- Hogging/ Trim saw tiltable unit, 5 HP , 3,600 RPM motor, 1" arbor and up to 10" blade. -- Jump Shape/coping head unit. , 7.5 HP - 4,500-7,000 RPM motor, 1" dia. arbor for 6" to 10" cutter head. -- Jump Shape/coping head unit. , 7.5 HP - 4,500-7,000 RPM motor, 1" dia. arbor for 6" to 10" cutter head -- Variable feed speed from 20 - 66 FPM, 2 HP motor, steel feed chains with plastic anti-slip pads and dogs at 16" center. -- Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Hopper feed magazine (additional $ 3,960) -- Sound enclosure (additional $ 9,500) -- Extended infeed 42" in front of hold down belt ( additional $5,600)Floor space : 14' X 9' X 5", weight 10,500 lbs

Louis Sicotte
800-374-5009 ext:329
Call

Challoner 527TS  Tennoner
Call for Price

Challoner 527 TS Dbl End Tennor w/Controls Serial Number: 403150 Doerr Electric Corp Motor Model: 71528 128/6.4 Amps 3 Phase 220/440 Volts 5 hp 3500 rpm Comes With Transformer and Control Panel Type: 12_4 480 3 Phase Overall Measures 146" Wide X 149" Long X 80" Tall

 Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Call

1984 CKM TS  Tennoner
$3,950

CKM TS Single End Tenoner -- (4) head single end tenoner -- (1) cutting saw -- ((2) top and bottom tenon head -- (1) coping head -- Manual Sliding table with fence

 EASTERN CDN, AL
EX-FACTORY INC.
704-841-2001
Call

Fletcher Machinery FM-200D Tenoner  Tennoner
Call for Price

This machine has been in storage for 4-5 years. There are (2) machines available.

Carolina Machinery Sales, Inc
704-288-1904
Call

Contact Us
  • Toll Free & Canada: (800) 477-7606
  • Direct & International: (931)381-1638
  • Location: 2508 Pillow Dr. Columbia, TN 38401
Copyright © 2020 LumbermenOnline.com - All Rights Reserved