Sanders For Sale

Oakley Edge Sander

(2) - 30" Dia. steel discs, 5 HP double shafted motor turns @ 1,050 RPM; (2) steel side tables 40" x 15", (1) slotted and (1) plain, both tables tilt 10ø up and 45ø down, (1) table has 6" manual vertical adjustment; rack travel adjustment by screw and crank. -- Complete with: Magnetic controls, (2) dust outlets and large hand wheels for easy adjustments.

OLIVER 6910 Oscillating Spindle SanderPedestal style Spindle Sander constructed for rugged use .Specifications: -- 2 HP Motor drives and is connected through a flexible coupling, and can be installed or removed without disturbing the drive mechanism. -- Spindle speed 1,725 RPM, Oscillation speed 75 Cy/Min with 1-1/2" stroke length. -- Spindle quill runs in precision ball bearings, oscillated by a heavy duty worm & gear mechanism running in a bath of oil. -- (10) Spindle sizes provided: 1/4 x 5", 3/8 x 6", 1/2 x 6", 5/8 x 6", 3/4 x 9", 1 x 9", 1 1/2 x 9", 2 x 9", 3 x 9" and 4 x 9"; 100 grit abrasive sanding sleeve with each spindle. -- Large 24" x 24" precision ground cast iron table mounted on large trunnions that can be tilted 45° down and 30° up by use of a convenient handwheel. -- Complete with: Pedestal style stand.

OLIVER 5385 Single Head Wide Belt SANDER (37") 1-Head and 37" belt width Combination Sanding Head with rubber covered contact roll and adjustable finishing platen, 1/8" - 5" Thickness capacity, 36" width capacity.Specifications: -- 20 HP Main drive motor. -- 1 HP Variable speed (15 to 45 FPM). -- 1/4 HP Power raising and lowering conveyor bed motor. -- 37" X 75” Abrasive belts for longer life and less loading.Features; -- Central control panel features digital thickness set-up control for accurate stock height and removal. -- Four post lift design assures accurate consistent results. -- Oscillating belt is controlled by an air sensor to prevent sanding lines. -- Finishing Platen is fully adjustable and can be removed. -- Multiple dust ports for efficient dust management. -- Independent motors run the sanding belt, feed conveyor, and table elevation for maximum power to each operation.

OLIVER 5390 Dual Head Wide Belt Sander1/8" to 6" Thickness capacity 36" Width capacity.Equipped with: -- 20 HP main drive motor, 2 HP variable conveyor feed 15 to 49 FPM.Head configuration: -- 1st Head: Contact drum -- 2nd Head: Roller and PlatenFeatures: -- Digital thickness controller w/ thousandth's jog feature. -- Omron electronic eye sanding belt tracking. -- Variable speed drive 15 to 49 FPM -- Power raising and lowering of the conveyor with digital thickness set-upSpecification: -- Max. width cap 36" -- Feed motor 2 HP -- Elevation motor 0.5 HP -- Max. thickness 6" -- Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 4.75" dia. with 2" wide finishing Platen -- CFM requirements 3600 -- Feed speeds 15 - 49 FPM -- Belt size 37" x 60".

Optisand L202 Moulding Sander

Powermatic OES9138 Oscillating Edge Sander Includes: (5) Sander belts

POWERMATIC WB-25 WIDE BELT SANDER1-Head, 25" width capacity, 1/8" to 6" thickness capacity. Combination sanding head with 4" dia. rubber covered contact roll & 2" wide polishing platen, micro-adjust platen. steel abrasive belt tension roll and steel idler roll. 25" X 75 abrasive belt capacity. Equipped with: -- 15 HP Three-phase main motor, 1 HP variable feed motor, 15-49 FPM. -- 1/4 HP table raising and lowering motor with Auto adjust thickness assist, 1/8" to 6" opening with (4) screw jacks. -- Double infeed & outfeed rubber covered holddown rolls. -- Complete with: -- Digital readout, air eye belt sensing, limit switch overtravel protection, magnetic starter, overload protection, load meter and emergency brake; includes owner's manual & parts list.

20" Dia. dynamically balanced aluminum disc, 3 HP - 1,740 RPM direct drive motor; 15" x 27-1/4" table w/miter gage slot, tilts 30° upward & lowers 45° downward, 90° positive table stop; rack mechanism for raising & lowering table by hand crank, heavy bolt-down steel base. Complete with reversing switch and miter gauge. Also available in Single-phase in 2 HP motor.

POWERMATIC RB-37 SINGLE HEAD WIDE BELT SANDER1-Head, 36" width cap., combination sanding head with 4" dia. contact roll & 2" wide polishing platen, micro-adjust platen; 15 HP main motor. -- Abrasive belt size 37" x 60", with air tensioning, air jet abrasive belt tracking; 1 HP feed drive, variable feed speed of 15 - 30 FPM conveyor speed, 0" to 5-1/4" opening with (4) screw jacks, double infeed & outfeed rubber covered holddown rolls. -- Complete with: Magnetic starter, overload protection, load meter and emergency brake.

PROFILEMATIC 503 PROFILE SANDER3-Head feed through, sands from top at adjustable angles narrow moulding type parts as well profiled edges on panels.Equipped with: -- (3) Top VPS vibrating air-loaded sanding units, 0.5 HP vibrating motor ea., sanding heads have (2) pneumatic cylinders for sanding pressure control and oscillate with 1/2" stroke on dust-protected round guides, variable vibration speed from 200 - 1,800 RPM; adjustment range of 120ø to conform to profile, equipped with air shower to clean workpiece & sandpaper automatically. -- Part transport is achieved by a 4-1/2" wide linatex coated conveyor belt system, "quick adjustment" holddown wheels & fence system, variable feed speed 0 - 35 FPM powered by a 0.25 HP DC gear drive (forward & reverse feed mode). -- Each sanding head with its own controls for manual raise & lower, pressure control and vibrating speed. Profile width approx. 1/2" min. to 4" max., material feed through thickness up to 5"; support fences for up to 10" moulding width.

2 HP motor,220V, 3 PH, 60 HZ -- V-belt drive, Allen Bradley push button overload control. -- Seller recommends replacing rubbers & covers.

PROSAND HF-412 Curved Part Belt SanderBelt oscillates up and down.÷Feed wheel removable.

QUICKWOOD CD2-300 Moulding & Profile Sander or Denibber;4-Head Brush Loading Sander, 12" width and 4" height cap., for 3-sided sanding & denibbing. Head Configuration: -- (2) "BH300" Overhead rotating abrasive/brush heads, both arbors equipped with a combination of abrasive and brush loadings, 12" long arbors, 12" max. dia. sanding discs. -- 0.75 HP Motor drives each arbor with inverter for 200 - 1,200 RPM arbor rotation speed. -- Right & Left ("BH-140" & "BH-100" respectively) side mounted rotating abrasive/brush heads. -- Tilting heads and adjustable in-and-out, 6" long arbor, 8" dia. sanding discs, 0.5 HP motor each head. -- 0" - 4" Max. manual part height adjustment via hand wheel; 57-1/2" long roller conveyor with PVC covered rollers, variable feed speed 10 - 60 FPM. -- Infeed & outfeed overhead holddown rolls and (1) between the top heads. Includes centralized control panel, hubs, abrasive, & brush. -- Can also be ordered with just (2) top heads or (3) heads, ie. Left or Right. Call for separate prices.

Quickwood RO 1300 Sander

Quickwood Pro 1100 Sander

Quickwood Pro 1600 Sander

8 or more brushes arranged at 360 ° with respect to the work pieces Adjustable inclination for the profile step QRC module for the super finishing of the flat parts in view

RAMCO 37T/60 Single Head Wide Belt Sander; (1) Head, 37" width capacity, combination head with contact roll and basic dual purpose finishing platen. -- 20 HP main motor; 37" x 60" abrasive belt with electronic tracking and pneumatic belt tensioning. -- 1 HP Feed drive, variable feed speed 20 - 80 FPM, infeed & outfeed holddown rollers. -- 0" TO 6" Thickness capacity. -- Complete with: Load meter and safety bumper.

Single head, 36" width cap. - 7" Dia. rubber covered contact snadeing roll followed by an adjustable 2-1/2" Wide finishing platen, 20 HP motor. -- 37" x 75" Abrasive belts, electronic abrasive belt tracking. -- Equipped with: Infeed & outfeed spring loaded holddown rolls, 0" - 6" max. motorized part thickness opening and Programmable thickness adjustment; 15 - 45 FPM variable feed speed driven by a 2 HP. motor. -- Complete with: Air operated disc brakes, motor load meters.