Woodworking Equipment For Sale

YATES AMERICAN B-26 Top & Bottom Rough Lumber Planer24" x 4" Opening cap., 3/4" to 4" thickness capacity; 46" minimum unbutted length capacity;Specifications: -- (1) 75 HP DMD motor power hoisted top head, (1) 40 HP DMD motor bottom head, 8" dia. cutting circle at 3,450 RPM. -- 40 HP Hydraulic power unit for variable feed rate from 75 to 400 FPM, 12" dia. Urethane tire top feed rolls, 12" dia. non-powered lower rolls. Equipped with: -- Carbide spiral cutterheads, automatic pressure bar release (hydraulically operated), hydraulic top & bottom headlocks, anti-lap bar device, air tensioned & released chipbreaker. -- Complete with: Built-in top & bottom jointers, dust hoods, electrically interlocked safety guards, and small remote operator's console.

YATES AMERICAN - B-26: Top & Bottom Rough Lumber Planer24" x 4" Opening cap.; 3/4" - 4" thickness capacity; 46" min. unbutted length capacity.Specifications -- (1) 75 HP DMD Motor power hoisted top head; (1) 40 HP DMD motor bottom head; 8" dia. cutting circle at 3,450 RPM. -- 2 HP Hydraulic power unit; variable feed rate: 75 - 400 FPM; 12" dia. urethane tire top feed rolls; 12" dia. non-powered lower rolls. Equipped with: -- 10-Knife Carbide cutterheads; automatic pressure bar release (hydraulically operated); hydraulic top & bottom headlocks; anti-lap bar device; air tensioned & released chipbreaker.Complete with: -- Built-in top & bottom jointers. -- Dust hoods (not shown on picture). -- Electrically interlocked safety guards. -- Top infeed /outfeed rubber rollers.

YATES-AMERICAN - B-244: 30" Planer30" x 8" Cap., 7-1/2 HP - 3,600 RPM direct drive motor; 4-knife 4-1/4" dia. cutterhead; 1/8" min. material thickness; 11" min. unbutted stock length; 3-1/4" min. butted stock length. -- 30" x 40" Cast iron table bed; manual raise-and-lower on (2) 1-3" /8 dia. hoist screws; belt drive feed system; variable speed 25 - 70 FPM; (2) 4" dia. powered upper rollers with: Sectional top in feed roll; (2) 4" dia. bed rollers; sectional chipbreaker. Fully restored in 2025 -- 240 VAC, 3 Phase, 3600 RPM; 7-1/2 HP direct drive cutterhead motor; 3/4 HP separate drive train motor. -- 4-Wheel drive: All (4) rollers are powered for stock feed. -- Segmented infeed roll & chip breaker: Both rebuilt with: New springs; spring caps; graphite lubricant. -- (2) New, hardened 52100 steel bearing shafts; heat treated at SW Metal Treating in Fort Worth; precision ground at Fort Worth Centerless grinding. -- Fully repaired & insulated leads on the motor stator. Stator was fully checked at "T-Gray Electric" in Dallas; all tests passed. Results report included. -- Upgraded threaded riser shafts from: 1-1/4" to 1-3/8". -- Improved REEVES Drive motor mount collar. -- Rebuilt drive train motor with: New bearings. -- New TIMKEN cutterhead bearings; new needle bearings where required. -- Dynamically balanced cutterhead and motor rotor assembly. -- New cutterhead knives. -- Rebuilt power transfer shaft housing. -- New transmission frame & speed adjustment linkage. -- Rebuilt speed control knob. -- (2) new drive train chains. -- Everything: Fully stripped, degreased, derusted, primed, painted. -- Custom start button console. -- Table & table rollers: Residual rust pitting that does not affect performance or surface finish. -- Custom dust chute with: 8" hose adapter.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Yates-American A-20 planer. 4 sided with profile machine, 10" rolls, tongue and groove heads. Includes 10 cylinder Deutz engine, belt drive assembly, extra heads, Newman planer infeed with spiral rolls. As/is-where/is, as removed from service. Price Reduced $39,000. 

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Yates American B-15 Helical Head Planer S/N 29658

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

Planer Head Set Up Stand

Yates American B24 Planer

Yates American B-26 Top/Bottom Planer 24” capacity Each head has (10) straight knives and are jointed on the fly 460 volt 3- phase

Yates-American Planer Mdl. 415M, S/N: 25264, $30,000

ZEETECH - 200, ...Universal Hopper Feeder that can be mounted to all Moulders. - Capacity: 3/4" - 9-1/2" width, 0.38" - 5" max. material height, 10" min. length. -- Oil-free air operated drive unit mounted on THOMPSON hardened ways, damped drive travel, positive sensing sequencing actuator. -- Variable speed range from 0 - 120 FPM @ 80 - 120 PSI. -- Includes: All air logic controls (no power required) and air filters; easy to install.

ZINTEXX 5200 Abrasive Blast Media Belt Cleaner for Wide Belt Sanders; -- Utilizes ground glass to clean belts. -- Traverse variable speed D/C drive motor with adjustable limit switches, maximum stroke 60".Specifications: -- 30 SCFM @ 52 PSI (max.); 850 liters/minute @ 3.45 bar (42 SCFM); 115 V, 1 Ph., 60 Hz, 20 AMP. -- The cleaner will automatically move the nozzle across the belt surface. Speed is adjustable from 0 to 100. -- Digital Counter must be connected to dust collection, 800 CFM minimum. -- Ground glass blasting media available from McMaster Carr.Overall Dimensions: -- 85.5" W x 39" D x 68.5" H; 100 Lbs dry weight.

ZUCKERMANN CHALLENGER 1700 37-Z SYNCHRO Copy Lathe. Single spindle hopper feed CNC Copy Lathe for shaping & sanding asymmetrical parts. -- Size Capacity: 67" Maximum 67" (1700mm) and 4" (100mm) minimum working length, 9.8" maximum working diameter. -- Drives/Speeds: The cutter head is belt driven by 5.5 HP motor to run at 6,000 RPM, sanding motor 1.5 HP to drive a 5-7/8" wide sanding belt. Work piece rotation CNC controlled for variable rate from 12 - 130 RPM, via 4 HP motor, carriage speed CNC controlled 7- 67 inches per minute, automatic hopper feed as well as automatic unloading . -- Controls: Machine sequencing, cutting and sanding speeds controlled by SIEMENS "Sinumerik 810 T" CNC controller with programmable memory for rapid set up. --Complete with: Various spare parts & 220 or 440 V operation transformer.

ZUCKERMANN CHALLEGER Copy Lathe w/Sander for asymmetric/irregular shaped parts.Hopper feed, single spindle; approx. 149" (3,800 mm) max. between centers, 8-13/16" (250 mm) max. part dia.; 5 HP cutter head motor at 6,000 RPM, oscillating belt sanding unit, both units work together. -- 'Cup' style Cutter head; 2 HP spindle & pattern rotation motor; mechanical & pneumatic traverse of cutter head and sanding carriage. -- Complete with: Built-in operator push button control panel and overhead dust collector hood.