Woodworking Equipment For Sale

WYSONG & MILES 604 DOUBLE SIDED OSCILLATING EDGE SANDERDouble Sided Oscilating Edge Sander with 7.5 HP - 1,800 RPM TEFC motor; (2) 11" x 60" cast iron platens; 10" x 172" abrasive belt size, (150) oscillations/Min with 1/2" movement, 0.5 HP oscillation motor.Equipped with: -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table; tables tilt 30° up & 45° down; 5" vertical table travel w/hand wheel adjustment, 5" lateral side table travel w/hand wheel adjustment, 4-1/2" lateral end table travel w/handwheel adjustment. -- 10" Dia. x 10-1/2" face direct drive pulley, 4-1/2" dia. x 10-1/2" idle pulley. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

WYSONG & MILES - 315, ...Edge Sander6" x 32" Graphite mocovered wooden platen; double 8" x 34" tilting side tables; full 180° steel end table; tilts and raises & lowers. -- 2 HP Motor; direct drive motor.

Used YAMAMOTO 30-opening, premium quality, Plywood Hot Press. -- 500 Tons pressing capacity. -- Daylight is 4.7"(120mm). -- Press plates are 54" x 108" x 1.5" (1,370 x 2,700 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- Professional removal and loading available at Buyer's cost.

Used YAMAMOTO 45-opening, premium quality, Plywood Hot Press. -- 500 Tons Pressure Capacity. -- Daylight is 2.75" (70 mm). -- Press Platens are 106" x 53" x 1.57" (2,700 x 1,350 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- This particular press was only operated for about 1-1/2 years. -- Professional removal and loading available at Buyer's cost.

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

Yates-American A-20 planer. 4 sided with profile machine, 10" rolls. Includes 10 cylinder Detroit engine, belt drive assembly.

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American B-15 Helical Head Planer S/N 29658

YATES AMERICAN B-26 Top & Bottom Rough Lumber Planer24" x 4" Opening cap., 3/4" to 4" thickness capacity; 46" minimum unbutted length capacity;Specifications: -- (1) 75 HP DMD motor power hoisted top head, (1) 40 HP DMD motor bottom head, 8" dia. cutting circle at 3,450 RPM. -- 40 HP Hydraulic power unit for variable feed rate from 75 to 400 FPM, 12" dia. Urethane tire top feed rolls, 12" dia. non-powered lower rolls. Equipped with: -- Carbide spiral cutterheads, automatic pressure bar release (hydraulically operated), hydraulic top & bottom headlocks, anti-lap bar device, air tensioned & released chipbreaker. -- Complete with: Built-in top & bottom jointers, dust hoods, electrically interlocked safety guards, and small remote operator's console.

YATES AMERICAN - B-26: Top & Bottom Rough Lumber Planer24" x 4" Opening cap.; 3/4" - 4" thickness capacity; 46" min. unbutted length capacity.Specifications: -- (1) 75 HP DMD Motor power hoisted top head; (1) 40 HP DMD motor bottom head; 8" dia. cutting circle at 3,450 RPM. -- 2 HP Hydraulic power unit; variable feed rate: 75 - 400 FPM; 12" dia. urethane tire top feed rolls; 12" dia. non-powered lower rolls. Equipped with: -- 10-Knife Carbide cutterheads; automatic pressure bar release (hydraulically operated); hydraulic top & bottom headlocks; anti-lap bar device; air tensioned & released chipbreaker.Complete with: -- Built-in top & bottom jointers. -- Dust hoods (not shown on picture). -- Electrically interlocked safety guards. -- Top infeed /outfeed rubber rollers.

Setup stand, good condition

Planer Head Set Up Stand

There are two of these systems available. They were recently removed from the current operation and available immediately.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

ZANGHERI & BOSCHETTI B-35 CONSTRUCTION/LINE BORER(35) Spindles, 4 HP motor, drills vertically from the bottom/ horizontally from the back, 45° bevel drilling feature; (6) pneumatic holddown clamps for vertical & horizontal clamping, includes fences & stops. -- The 56" x 30" table shifts when changing from horizontal to vertical maintaining same boring depth and zero base. Removable table fence for extended length line boring.

ZEETECH - 200, ...Universal Hopper Feeder that can be mounted to all Moulders. - Capacity: 3/4" - 9-1/2" width, 0.38" - 5" max. material height, 10" min. length. -- Oil-free air operated drive unit mounted on THOMPSON hardened ways, damped drive travel, positive sensing sequencing actuator. -- Variable speed range from 0 - 120 FPM @ 80 - 120 PSI. -- Includes: All air logic controls (no power required) and air filters; easy to install.