Woodworking Equipment For Sale

Whitney S970 Planer Electric

MLS Number 11180323 Whitney Model 97 Planer 36 inch width capacity by 7 inch thickness 40 HP 3600 rpm top head motor 30 HP 3600 rpm bottom head motor 5 HP feed motor -variable speed 6 row Newman Quite-cut carbide knife heads 432 new carbide knives installed and ground 8 roll feed set-up Knife grinder and jointer Top head dust hood 480 volt, 3 phase electrical Serial no. 15819 Cleaned and checked

MLS Number 11570232 Whitney S970 Wood Planer A. 30 inch width by 7 inch thickness capacity B. 40 HP 3600 RPM top head motor , 3 phase ( Approx 50 amps on 480 volts ) C. 30 HP 3600 RPM bottom head motor, 3 phase ( Approx. 40 amps on 480 volts ) D. 5 HP feed motor ( Approx. 7.5 amps on 480 volts ) E. 50 to 150 FPM feed speeds F. ¾ HP raise-lower motor G. Newman 6 row Quite-cut carbide knife ( 5 inch cutting circle ) cutter-heads H. Knife grinder and jointing device I. Dust hoods J. Cleaned and checked K. Repaired Frame L. Serial No. 17977 ( Orig. Mfg. Approx. 1971 ) M. Electrical controls in separate cabinet

MLS Number 11570230 Whitney S970 Wood Planer A. 30 inch width by 7 inch thickness capacity B. 40 HP 3600 RPM top head motor , 3 phase ( Approx 50 amps on 480 volts ) C. 30 HP 3600 RPM bottom head motor, 3 phase ( Approx. 40 amps on 480 volts ) D. 5 HP feed motor ( Approx. 7.5 amps on 480 volts ) E. 50 to 150 FPM feed speeds F. ¾ HP raise-lower motor G. Newman 4 row Quite-cut carbide knife ( 5 inch cutting circle ) cutter-heads H. Knife grinder and jointing device I. Dust hoods J. Cleaned and checked K. Repaired Frame L. Serial No. 18343 ( Orig. Mfg. Approx. 1975 )

Williams 125 CJS1 Hammermill

Williams 125 HP Hammermill 230/460 3-phase

100 HP 230/460 volt 20” x 19” inlet 9” x 28” outlet no hopper

WILTON 4421-2 20" Pedestal-Type Disc SanderSpecifications: -- Table size 10-1/2" x 27-1/2", Table tilt 45° Out/30° In, Table can be lowered below disc to accommodate large workpieces.Equipped with: -- 3 HP 1,720 RPM Direct drive motor, Low voltage protection switch. -- Positive lock rack & gear table tilt.

Wintersteiger DSG Sonic Frame Saw

Wisconsin B20-M multiple spindle horizontal drilling machine 8' 4-HEAD 13-SPINDLE DRILLING MACHINE 3 HP DRILLING MOTORS, HYDRAULIC , AIR CLAMP Serial # B20M-6825-96 5 HP hydraulic pump: 230/460V, model CLT-30 GAL, 1050 psi, 8 GPM., serial# 1-89175-0 Four Baldor Drilling motors 3 HP, 208-230/460 volts, 3450 RPM., Baldor, Removed from a complete plant liquidation in October 2020. Stored inside a climate controlled room, Contact us for a delivered price

MLS Number 10684323 Wisconsin Automated Machine C-450 Tennoner Single end tennoner Automatic double head coping tennoner Model C-450 Serial: C-450-6901-00 230 volts, 3 phase, 60 Hz. Allen-Bradley and Motortronics electrical Motors are 230 volts 48 full load amps. 15.2 amps on largest motor

32" Vertical grinder with 25 HP motor Dentom 624 9500 BTU Furnace automated measured feed controlled by furnace temperature Holding tank for feed from the grinder which is automatically fed to the furnace...that feed is temperature controlled.

Woodmizer HR120 horizontal resaw., single phase 10HP motor, runs good, can do a 16"x8" piece. $7,500

Woods 502M hardwood flooring machine

WOODS Planer-Matcher - Model 412 motorized, heavy duty planer-matcher with 6 heads. Ideal machine for surfacing dimension lumber or specialty products such as siding and flooring. 6" x 14" capacity, 8 knife heads; 50 hp top, 25 hp bottom, 20 hp sides; 20 hp bottom profile, 15 hp top profile. Item 32203.

Woodtek 2 Spindle Boring Machine

Dry glue joints in seconds.

WYSONG & MILES Edge Sander6" x 32" Graphite mocovered wooden platen, Double 8" x 34" tilting side tables, full 180ø steel end table, tilts and raises & lowers. --2 HP motor, direct drive motor.

5 HP - 1,200 RPM motor, roller table size 32" x 84", horizontal travel stroke 38", adjustable height of table base from 26" to 35" via large hand wheel. -- Rubber-faced Aluminum Pullies 8-1/2" face x 16" dia., accepts 6" wide abrasive sanding belts, pulleys can be spaced to accommodate various belt & material sizes, belt loop travels over table with manual handwheel belt tension & tracking. -- Includes: Magnetic starter, dust hoods

WYSONG & MILES NO. 303 COMBINATION DISK AND OSCILLATING SPINDLE SANDERThis machine is two in one. It features a 26″ disk sander with a 15″ X 34″ titling table (to 45 degrees) on one side. On the other you will find an oscillating spindle sander featuring a 24″ X 24″ tilting table (15 degrees forward and 35 degrees backward) with a 2″ X 8″ oscillating spindle. -- Power for each is provided via a 5 HP motor. A swing out arm holds a 2 gallon bucket to the side of the machine for small parts or waste. -- Machine is 220V/440V/3 Phase. -- The only repair we see is a braze on the motor mount which is a very old repair and does not effect machine operation. &#9679 This fully functional machine has been fully cleaned and checked