Woodworking Equipment For Sale

TIMESAVERS 1311-13-1 SINGLE HEAD WIDE BELT SANDER1-Head, 37" cap., 0 - 5"opening (33" - 38" passline). -- Combination head with 4-3/4" contact roll & 2-1/2" finishing platen, 15 HP motor. - 37" x 60" Abrasive belt, disc brakes on main motor, centralized control panel. -- Features: Digital thickness readout, double infeed & outfeed holddown rollers, variable feed speed from 20 - 40 FPM, hour meter, main motor load meter/watt meter. -- Includes Dial indicators on drums/platen, auto setup device, motorized lift, 13" infeed loading area, (4) bed jacks, quick release outboard support, through-beam abrasives belt tracking, infeed stop bar, and UL listed controls. Extra Sanding belts included

TIMESAVERS BM24-2 Wood Brush Sander. One 24" sanding brush is followed by a second brush for finish or sealer sanding. -- Includes MASTER SAND (1) set of hubs and steel wire brushes. -- Drives: 7.5 HP Variable Speed Drives on each head. 1 HP Variable Mechanical feed drive. Feed speed is adjustable from 10 - 40 FPM. -- Features: Spring-Loaded holddown rolls that can feed min. 12" long parts. Rough-top conveyor belt. (2) dust outlet connections at 4" dia. requiring about 450 CFM each.Other Specifications: -- Sanding wheel diameters: 11" rotating at 200 - 1,200 RPM. -- Feed/Passline height variable: 29 - 34.5" -- Maximum workpiece width: 24". -- Maximum workpiece height: 5.5". Minimum thickness: 0.200" -- Dust collection required: 900 CFM. -- Machine dimensions/Weight: 58" Long, 48" wide, 52" high. 925 Lbs. -- Electrical Load: 21 Amps @ 460/3/60.

TIMESAVERS 2321-24-01 Wide Belt Sander (2) Heads43" width cap. Drum, Combination HeadHead configuration:1st Head: 8" Dia. rubber covered contact roll 65/70 Duro. , 25 HP motor (4,000 RPM);2nd Head: Combination head with 5-1/2" dia rubber covered contact roll and 2-1/2" wide finishing platen, 20 HP motor (3,500 RPM)Specifications: -- 43" x 75" Abrasive belts with dual "Posi-Trak" electronic solid-state tracking --Conveyor belt feed with AC inverter variable feed from 15 - 45 FPM. -- Infeed & outfeed spring loaded holddown shoes or rollers on all heads --Automatic part thickness set-up, motorized thickness adjustment with digital indicator, 0" - 6" opening, and infeed safety stop bar. -- (4) Jack screws for bed adjustment --Compressed air requirements: 4 CFM @ 90 PSI --Dust extraction requirements: 2,700 CFM --Electrical requirements: 126 full load amps @ 230 VoltEquipped with & Features: -- Controls mounted on belt loading side -- 14" infeed conveyor area -- Sanding head motors with air caliper disc brakes, and motor load meters. -- Well maintained and serviceNOTE Constant Passline Sander 33"-38"

TIMESAVERS 36" SPEEDSANDER WIDE BELT SANDER1-Head, 36" width cap., combination sanding head with 4" dia. contact roll & 1-1/2" wide polishing platen, 7.5 HP 1-phase motor. -- Abrasive belt size 37" x 60" with electronic abrasive belt tracking, 4" max. thickness with 34" - 38" passline; Rough-top conveyor with 5 - 20 FPM variable feed via AC Frequency drive. -- Equipped with: Air activated emergency brake, outboard door interlock, infeed emergency stop bar, and emergency stop buttons on outfeed. -- Includes: (1) 4" Dust outlet, Proscale digital readout, and casters.

Dust Collection System

Reconditioned Torit 156RF10 baghouse

TORREDA HIDROPAL-1400 COPY LATHE

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Custom Ceiling / Flooring Table Table Size: 32' x 6'9" to 14'3" Table Operated by Both Push Button and Key Fob Controls Floor can be built manually on the table Clamping Stud Locators at 16" & 24"

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

40? deep X 87.5? wide capacity. The Maximum opening is 49.5? and the pods will extend 9.5? for a minimum opening of 40?. The press is rated to 100 PSI and has (1) pod short of 100% pod coverage. That being the center bags are staggered. There are spring loaded bed rollers to aid in loading and unloading. The top and bottom plates are dent free and no air leaks This fully functional machine has been fully cleaned and checked and is ready to work..

TYLER 703 Power Pod Cold PressTyler Air Pod Press with a Platen dimension of 40″ Wide X 87-1/2" Long. -- The Maximum Daylight Opening is 49.5″, and the pods will extend 9.5″ for a minimum opening of 40″. -- The top and bottom plates are dent free. -- The press is rated to 100 PSI and has (1) pod short of 100% pod coverage (being that the center bags are staggered). -- There are spring loaded bed rollers to aid in loading and unloading. .This machine has been cleaned and checked and there are no air leaks.

--In Auctions; https://exfactoryauctions.com/Detail/DL-230113/event/A122024$1 - NO RESERVE -- TYLER French-Type Dovetail Machine Equipped with: (2) 14-1/2” x 17” Tables. (2) 2 HP Routing heads for mounting of drawer sides. (1) 2 HP Grooving head for drawer bottom dado, (2) 2-Spindle Vertical boring heads for drawer hardware. (2) Pneumatic hold-down clamps

UHLING HP-3000 55" L x 96" H x 24" D Single-Bay Pneumatic Case Clamp Specifications: Clamping Cap. 55" L x 96" H x 24" D, Accommodates multiple boxes. Air pod stroke 3-1/2", Pressure adjustment 0 - 120 PSI. Setup time (25) Sec., Changeover time (30) Sec. Equipped with: Vertical beam, with (3) Counterweight-balanced & (1) Stationary 24” W x 5-3/4” H dual air pod pressure bars, Roller bearing mounted carriage with Pneumatic locks, Adjustable in 5” increments. Solid back support. Adjustable squaring arms. Carriage mounted control panel, with Single lever lock & Individual air pod selection. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

UHLING - HP-3000, ...Case Clamp (Single-Bay): --SpecificationsClamping capacity: 55" L x 96" H x 24" D; large enough for multiple boxes. Offers: Versatility, quick 30-second setup or changeover. -- Pressure Elements:(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; position them effortlessly and let go. The counterweight keeps them in place; no need to secure them! -- Air Pod Stroke:3-1/2" Stroke of air pod with: 0 - 120 PSI Pressure adjustment. -- Vertical Beam:Moves easily on roller bearings with pneumatic carriage locks; (4) small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam, so it is always where it is needed; single-lever lock-or-unlock control & front/rear pressure selection. -- Counter Support by:Solid laminated panel opposite to pressure bars.

UHLING - HP 4000, ...Case Clamp (Semi-Automatic) -- Specifications100" Wide x 50" high x 24" deep clamping cap. and built with a Heavy wall steel frame construction. - Super "easy & quick" manual positioning of vertical side pressure carriage and top pressure beam. -- Includes: Push button release, pneumatic locking and "counterbalanced" movement of horizontal top pressure beam; vertical side pressure carriage with single lever release & lock; locks in place with (4) air cylinders and rides on bearings for quick & easy positioning. -- Vertical & horizontal pressure beam equipped with: (5) Adjustable "dual" ram air pod pressure shoes (3 on the top horizontal beam & 2 on the side vertical beam); 3-1/2" clamping stroke; features individual air pod selection. -- Since the pressure bar is positioned over the joint (or shelf), it will automatically compensate for sizing inaccuracy. -- Independent controls for top & side pressure and timer for clamping cycle; solid bottom & back support for any size case. -- Air flow pressure controls & pressure gauges built into traveling vertical carriage (always close to the Operator). -- Overall dimensions: 143" x 90" x 30".

UHLING - HP 2000, ... Case Clamp (Pneumatic) Specifications: -- Offers a compact, quick, and easy-to-use Case Clamp. -- 50" x 42" x 24" Clamping cap. that can handle ...80% - 90% of your case good needs. -- (2) Counterweight-balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks. -- Single-lever lock or unlock control and front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access Operator's Control Panel that is mounted on the vertical beam.