Cutler-Hammer For Sale

CANTEK - GT400BRD 16″ Double Surface PlanerGeneral description: -- Spring-loaded conveyor pin system ensures material is passed over the bottom cutterhead to resulting in a flat and uniform board prior to planning to thickness on the top head. -- Spiral insert knife cutterheads with two-sided solid carbide knives produce a smooth finish with increased stock removal capacity and extremely quiet operation. -- Heavy-duty cast-iron machine body and table for vibration-free cutting.Digital electronic thickness adjustment in INCH and MM (Inch = 0.001"; / mm = 0.01mm resolution) for precise thickness control KEY ADVANTAGES SERVICESpecifications: -- 16″ Wide x 6.7″ thick planing capacity -- 10 HP Bottom Head and 15 HP Top Head -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. Cutterhead speed 5,400 RPM. (2) Driven and (1) idle bed roll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls -- Inverter variable speed control with feed speeds from 26 to 80 FPM, 2 HP variable feed drive.Features: -- Easy to access external handwheel adjustment of infeed bed -- Hard chromed worktable for high wear resistance -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways -- Section chipbreaker and sectional feed roller before top cutterhead -- Rubber outfeed top roller to prevent chip marking -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on control panel to monitor motor load -- Star-Delta soft start.

CANTEK - GT635ARD-16 25″ Double Surface Planer25″ Wide x 16″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external handwheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 16″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK - GT635ARD-8 25″ Double Surface Planer25″ Wide x 8″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external hand wheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 8″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK GT610HI CARDAN SHAFT DRIVE DOUBLE SURFACE PLANERSpecifications: -- Max. working width 24" (610 mm). -- Max. working thickness 8" (200 mm). -- Min. working thickness 5/16″ (8 mm). -- Min. working length 12" (300 mm). -- Cutterhead RPM 5000 RPMCutterhead diameter 5.3" (135 mm). -- Feed speed 30-98 FPM 10 – 30 m/min. -- Top cutterhead motor 40 HP. -- Bottom cutterhead motor 30 HP. -- Feed motor 5 HP. -- Table Rolls 7 (3) driven. -- Opening hoist motor 1 HP. Machine dimensions: (LxWxH) 112"; x 67"; x 67"; 2830x1700x1700mm . Machine weight 8800 Lbs 4000 kgsShipping weight 9240 lbs 4200 kgs. -- Shipping dimensions (LxWxH) 115"; x 75"; x 75"; 2900 x 1900 x 1900mmMachine electrics (Standard) 460/3/60 = 110 amps (Other voltages on request, factory order)Key Advantages• Cast iron machine frame for superior vibration damping resulting in a long machine & bearing life.• Chrome-plated tables and top and bottom for maximum wear resistance.• Cutterheads are mounted in precision ABEC 7 RHP bearings.• The feed system uses a spring-loaded pin arrangement to pass material over the bottom jointing head.• Sectional serrated infeed roll before the top cutterhead.• Variable feed speed by frequency inverter (VFD) with digital display for the feed speed.• Digital thickness control for quickly and precisely setting the desired thickness.• The upper assembly is adjusted for desired thickness by four large-diameter cylindrical posts.• Adjustable infeed bed by easily accessible handwheel to set desired stock removal on the bottom head.• Easy to access swivel control panel with individual ammeters for load monitoring and hour meter to aid in maintenance planning.• Cutterhead starters are Y-Delta providing a soft start to the heads for reduced power consumption on startup.• Automatic lubrication to the conveyor feed system.• High-quality Schneider electrical components to CSA/UL standard.

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300mm) for both straight and profile grind; dia. of knife swing 12" (300mm). Grinding arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1500 to 4200 RPM. Quick change removable (140mm) wheel adapter. Machine set for axial constant grinding and template set up on right hand side. Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10°/15°. Quick change stylus turret for applications. (6) included with machine. Carriage: SCHNEEBERGER lineal bearing table movement. Table movement 12" x 6". Coolant system: 1/8 HP motor from coolant pump located in tank below. (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout!Option included: Motorized Side Clearance – including set left and set right Motorized Wheel Back Clearance Angle Motorized Grinding Wheel In/Out

CANTEK - PCM 120, ...Hollow Chisel MortiserFeatures: -- Power stroke of head permits easy, fast, and accurate successive cuts. -- Separate fan blower to keep work clean and free from dust & chips. -- Manual adjustable table height and lateral position. -- Heavy-Duty cast iron construction. -- Convenient centralized control panel. -- Foot pedal actuated cycle. -- Pneumatic workpiece clamping by lever.Specifications: -- Chisel range: 1/4" - 3/4"; Motor; 2 HP; Spindle speed: 3,400 RPM. -- Table: 16-3/4" x 21-1/4; Table tilts 30°. -- Air pressure: 8kG Clamping; Cylinder: 2-1/2"; (63 mm). -- Head traveling cylinder: 3.15"; (80 mm); Table cross travel: 5";. -- Table longitudinal travel: 18";; Table vertical travel: 12";. -- Max. stock width: 12";; Max. mortising depth: 4";. -- Machine weight: 572 Lbs. -- Shipping weight: 726 Lbs; Shipping dimension: 35"; x 38"; x 70"; (880 x 960 x 1,780 mm).

CANTEK P 630HV Single-Sided Planer with Helical Head. --PLC digital control for auto-thickness setting. -- Sectional infeed roller and sectional chip breaker. -- Anti-kickback safety fingers for safe operation. -- Variable speed drive for optimum finish results according to the planing depth and material being planed. -- Quick-set table roll adjustment to aid in feeding difficult-to-feeling material. -- Steel spiral cutterhead with carbide inserts – 6 rows 86 inserts 30 x 12 x 1.5 mm cutters mounted on an angle for 'shear' cut. -- Exhaust hood with 6″ outlet. -- Flip open the upper hood for easy and convenient access to change the knives on the cutterhead. Safety limit switch on the cover will not allow the operator to run the machine with the hood open. -- 4 Table raising jackscrews.Specifications: -- Maximum planing width 24-3/4″. -- Maximum planing thickness 11-13/16″. -- Minimum planning thickness 3/8". -- Max. depth of cut 5/16″. -- Minimum length 8-3/4″. -- Table size 27″ x 34″. -- Feed speed 20-39 FPM Variable. -- Main motor 10 HP. -- Feed motor 1 HP. -- Power rise and fall of table 1/2 HP. -- Dust hood (1) 6". Machine dimensions: 51"; x 38"; x 47";. -- Shipping dimensions 44"; x 39"; x 52. -- Net weight 1804 Lbs. -- Shipping weight 2024 Lbs. -- Machine Electrics 230/3/60 - 31.6 amps, 460/3/60 - 15.8 amps. -- 575/3/60 - 12.8 amps

CANTEK - P-630HV, ...24" Single Sided Planer with Spiral Knife CutterheadSpecifications: -- Planing width: 24-3/4"; planing thickness: 3/8" - 11-13/16". -- Max. depth of cut: 5/16". -- Min. length: 8-3/4". -- Table size: 26-1/2" x 33-1/2". -- Cutterhead speed: 5,600 RPM. -- Variable feed speeds: 20 - 39 FPM. Equipped with: -- 98 mm (3.86") Dia. Steel spiral knife cutterhead with: (6) Rows of (86) 30 x 12 x 1.5 mm inserts mounted on angle for shear cut & 10 HP Motor. -- 3" Dia. Sectional infeed roller with: 1 HP Feed motor & chip breaker. -- (2) 2-7/8" Dia. idler rollers in table; quick-set adjustment. -- 1/2 HP Bed elevation motor. -- eTEK "CH-525" Digital thickness controller with: LCD Display & Touchpad.Complete with: -- Instruction Manual & Parts List.NOTE: Seller purchased new and states machine has light use.

CANTEK P-630HV 24" Single-Sided Planer, with Spiral Knife Cutterhead Specifications: Planing width 24-3/4", Planing thickness 3/8" - 11-13/16". Max. depth of cut 5/16". Min. length 8-3/4". Table size 26-1/2" x 33-1/2". Cutterhead speed 5,600 RPM. Variable feed speeds 20 - 39 FPM. Equipped with: 98 mm (3.86") Dia. Steel spiral knife cutterhead, with (6) Rows of (86) 30 x 12 x 1.5 mm Inserts mounted on angle for shear cut & 10 HP Motor. 3" Dia. Sectional infeed roller, with 1 HP Feed motor & Chip breaker. (2) 2-7/8" Dia. Idler rollers in table, Quick-set adjustment. 1/2 HP Bed elevation motor. eTEK "CH-525" Digital thickness controller, with LCD Display & Touchpad. Complete with: Instruction Manual & Parts List. NOTE: Seller purchased new and states machine has light use. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

CANTEK MT-610 24"; Rotary Milling PlanerSpecifications -- Heavy duty welded steel construction. --Moving table type -- Display position number. -- Alarm bell and flash light. -- Speed change for feeding, controlled by Inverter (VFD) -- Rubber Endless Belt. -- Automatic device for feed belt tracking. -- Air jet cleaner for cutter -- Working width 610mm -- Workpiece thickness 3-125mm Equipped with & Features -- Number of cutters 2 units -- Spindle motor power 20 HP -- Brush motor power 1 HP (150 mm dia) -- Vacuum motor power 1 HP (suction for conveyor belt) -- Feed motor power 1 HP -- Lifting motor power 0.5 HP

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CANTEK - MX340, ...Edgebander (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MX340 EDGEBANDER (COMPACT): (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications: -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations: -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MX340M Edgebander (Single Phase):The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thiknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Also available in 220V/3PH/ 60 Hz

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large-diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents the backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self-centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus unwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

CARLSON CD PINNER PLUS Cabinet Door Clamp & Pinner; 30" Wide x 48" High max. Capability. The ProMax Cabinet Door Pinner is an affordable system that squares, clamps and fastens a variety of cabinet door styles and sizes. This machine is designed to handle stile widths between 1-1/4" and 3-1/2" in 1/8" increments and any rail widths. Standard product minimum: approximately 7" wide X 6" tall for 2" stile and rail cabinet doors. Standard product maximum: approximately 30" wide X 60" tall for 2" stile and rail cabinet doors.General Specifications: -- Standard joy stick operation allows quick and accurate size adjustments. -- The frame is ergonomically designed at an angle for easy placement of sub-assembled door parts and fast removal of the finished product. -- Operating controls are simple and convenient to minimize training time. -- Machine functions are air powered with programmable electrical controls for accurate and reliable operation.Includes: -- Air motor drive system. -- Standard clamp pads. -- Cope & Stick door fastening. -- Spare tool assembly. -- Size upgrade - Height 60". -- Miter capability. -- Safety light curtain. Features: -- Heavy duty frame, low maintenance, powered size adjustments, precision linear bearings, overhead mar-proof clamping, programmable controller.

CASADEI FLEXA 17 Edgebander with Pre-Mill --÷Good versatile machine for small shop use, with fairly simple adjustments. --Specifications:0.4 mm - 3 mm Max. edge thickness cap., (0.5 mm to 3 mm for solid strip edge thickness ). 8 mm - 50 mm (0.3" - 1.97") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 80 mm wide x 140 mm long (3.15" x 5.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine. --Equipped with: --Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 1 Kg. capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle. --Work stations: -- Premilling unit with 3 HP - 8,300 RPM High Frequency motors. -- Single motor, double end trimming saw unit with (1) 0.25 HP - 12,000 RPM High Frequency motor. -- Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel is synchronized by the PLC control. -- Top & Bottom Trim station with (2) 0.45 HP - 12,000 RPM High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Top & Bottom 3 mm scrape station -- Top & Bottom Buffing unit with (2) 0.20 HP - 1,400 RPM motors. -- Fixed feed speed 23 FPM.

Panel height: 0.3 – 2.36” Coil edge thickness: .12” Strip edge thickness: .015 – .24” Max Overhang Total Top and Bottom: 0.16” Min panel width (min length of 8 ¼”: 3.54” Min panel length (min width of 3-15/16?): 5.5” Feed Speed: 33 f/min Glue Tank GP-200 Power: 2.4 kW Glue Capacity: 3.3 lbs End Trimming Unit IK/200 (each): .3 HP Cutting Speed: 12,000 RPM Blade Tilt: 0-15 deg. Top and Bottom Trimming TT/K Motor (each): .4 HP Cutting Speed: 12,000 RPM Shipping Footprint: 13' x 4' x 5' Weight: 2500 lbs Equipped With: – Pre-Milling Unit – Glue Applicator and Pressure Rollers – Edgebanding Trimming Guillotine – End Trim With 2 Tiltable Motors 0-15 deg. – Top and Bottom Trimming via 2 Motors – Profile/ Radius Scrape – Glue Scraping – Buffing

2016 Casadei Flexa 47 Edgebander 230 V/3 PH