Woodworking Equipment For Sale

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

Manufacturers Specification - ? [Specifications](https://extremausa.com/product/magnum-xp-series-25-double-sided-planer/#tab-test_tab) Horsepower: 40 / 30 HPVoltage: 230V / 460VPhase(s): 3 PHWidth: 25"Top Motor: 40 HPBottom Motor: 30 HPElevation Motor: 2 HPFeed Motor: 5 HPMax Thickness: 8"Min Thickness: 3/8"Min Stock Length: 16"Cutterhead RPM: 6000Top Cutter Access: Super SlideBottom Cutter Access: Super SlideDisc Brakes: YesFeed System: CarpetDrive System: ShaftFeed Speed: 20-110 ft/minCFM Requirements: 3000AMPS (220V/440V): 188 / 94Weight: 9300 lbs

Extrema EP-216 16" Double Side Planer

37" width capacity Single head 60" belt length Digital thickness controller Electronic belt tracking vVariable speed drive

EXTREMA XR-12LE STRAIGHT LINE RIP SAWCompact Straight-Line Rip Saw with a guaranteed 8' glue line. -- Powered by a 15 HP direct drive motor. -- Equipped with: a Wye-Delta soft start for lower amp requirements during start-up. -- Heat treated chain and raceway with automatic oiler. -- All SQUARE D electrical controls. -- Large 14-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size table saw.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

3 available 3 phase power Very low hours

2 available 3 phase power liow hours

Fanuc Robot with Controller Box and Teach Pendant Model: S-420iF Type: A05B-1313-B501 Part #: R98Y03430 Date: 1998.11

45 KVA 480 volt to 208Y/120

Felder Format 4 Tempora 60.16L Edgebander

Felder Creator 950 Premium CNC Center

Felder Creator 950

Felder Format 4 Edgebander Model: Tempora 6012

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Felder Format 4 Edgebander Model: Tempora 6012 Return conveyor is no longer available.

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.