Woodworking Equipment For Sale
1442 Results Found
2006 Heeseman sander, MFA6 Impression, Head 1- Drum, Head 2 - Crossbelt, Head 3 - Pad, Contact: 740-357-9795 $29,500.00
A&S 781 10HS Panel Saw Serial 71293 Motors On Saw Blades: 11 HP Motor 230-460 Volts 34-17 Amp 3 PH 3450 RPM Motor On Hyd Pump: 3HP Motor 208/230/460 Volts 8.5 8.2 4.1 Amp 3 PH 1725 RPM Inclosed Breaker Box: 3 PH - 100 Amp Includes Multiple Saw Blades And Sizes
ADOLF JOHN & COMPANY Model "FS IV" Automatic Guillotine;Specifications: -- 126" Max. length cap., 3-7/8" cutting height. -- 0.5 HP motorized parallel fence, adjustable from 1" - 64", push-button controlled travel with digital readout, micro-adjustment by hand wheel. -- 7" Wide hydraulic pressure beam with rack & pinion travel; 5.5 HP gear pump motor for pressure beam and knife cutting operation, approx. (2) Sec cycle time/cut; -- Complete with: (2) Palm buttons for safety.All Hydraulics were reconditioned in 2013, and Guillotine has been used very little since.
$18,900
AEM Model 75-430 Wide Belt Sander;Specifications: -- 2-Head, 43" wide x up to 8" thick capacity. -- 1st Head: Quiet Cut cutter head (style drum)- 25 HP. -- 2nd Head: 5" wide finishing platen - 20 HP. -- Pneumatic belt tracking, Abrasive belt size xx" x xx". -- Variable speed feed drive motor; powered open/close. -- Motor load meters. -- Front and rear lighting. -- Includes: Belt cart with (4) unused 150 grit belts and (2) unused 120 grit belts, extra parts and manual.
$9,800
AEM 370 Wide belt Sander1-Head, 37" width cap., combination sanding head; -- 4" Dia. rubberized contact roll & 2" wide polishing platen; 20 HP motor. -- Abrasive belt size 37" x 60", with air tensioning, electronic abrasive belt tracking; -- 1 HP single speed conveyor, 0" - 8" opening with (4) screw jacks. -- Double infeed & outfeed rubber covered holddown rolls. Complete with: -- Infeed conveyor extension, safety stop bar, load meter.
$5,200
AEM 502-37 O/B Single Head Orbital Sander - Finish Sanding; Specifications: -- 1-Head, 36" width cap., Orbital sanding head with a 6" dia. sanding platen; 5 HP motor. -- 1.5 HP Variable feed speed motor for 15 - 40 FPM, double infeed & double outfeed rubber covered holddown rollers; 0" - 5" manual part thickness opening with mechanical digital readout, (4) screw jacks for conveyor bed opening. -- Complete with: Infeed conveyor extension with safety stop switch and motor load meter, Heavy Duty endless conveyor belt. -- Centralized control panel with Feed Belt On/Off, Brush On/Off and Speed, control Circuit with hour meter, Orbit Control with Amp meter. -- Cleaning Brush on back of machine (outfeed) with dust collection port.
Call for Price
$12,500
AEM 502-37 Wide Belt Sander (2) Heads37" Width cap Drum, PlatenHead Configuration:1st Head: 5-1/2" Dia. rubber covered contact roll, 20 HP motor2nd Head: Polishing platen, 20 HP motorSpecifications --37" x 75" abrasive belts. --ACRO-TRAC" Electronic abrasive belt tracking --1.5 HP variable feed drive, feed speed from 10 - 50 FPM --Ruff Tex conveyor belt. --0" to 5-1/2" Automatic part thickness opening with mechanical digital readout (bed automaticlly stops at panel thickness).Equipped with & Features --Double infeed & outfeed pinch rolls on each head, -- 36" infeed conveyor area --Perimeter safety bump bar --Disc brakes, and load meters on main motors.
$5,975
AEM 137-1 WIDE BELT SANDER1-Head, 36" width cap. - Combination sanding head with 4" dia. rubberized contact roll & 1-1/2" wide "dual action" polishing platen.Equipped with: -- Abrasive belt size 37" x 60" -- Pneumatic belt tensioning -- POSI-TRACK electronic abrasive belt tracking. -- 20 HP main drive motor. -- 2 HP Variable feed speed motor for 15 - 45 FPM. -- Infeed & outfeed rubber covered holddown rolls -- 0" - 6" manual thickness adjustment. -- 24" Infeed conveyor extensions with over thick protection device at infeed,Complete with: -- Air-operated disc brakes on sanding head, emergency stop button
Call for Price
Nice Altendorf 12=14" TKR 90 Sliding Table Saw, owner is retiring 14" blade with scoring 7.5HP Motor 3 Phase
Call for Price
Call for Price
Call for Price
The seller has confirmed that these (2) Amitec VT veneer slicers are in good working/running condition. They are ready to load! - (2) Available - Slices log cants in the lengthwise direction - Compares to the Marunaka SL-250 - 9-7/8" (250mm) Max lumber slicing width: With up to 9-7/8" high cant, veneer thickness 1/25" to 3/8". 75° knife angle with 18 ° knife bevel - Knife length: 46-1/2" (1,180mm) - Motorized upper feed beam with Continuous belt feed - Variable speed: 120-180FPM (40-60 m/min) - 30HP feed motor - Head elevator: 1HP - Approximate weight: 16,000 lbs - 327"L x 62"W x 75"H
(1) Box of white accordion type filters for spray booth exhaust. Filter medium 3' high x 30' long (cut to size) 2-1/2" thick and (8) pleats per foot, with recommended air velocity of 100 - 200 FPM. Filtration efficiency at 150 FPM ranges from 91 - 98.1%. -- Price quoted is for (1) box delivered to your door (USA ONLY). -- Qty 3-5...$91.00 ea. -- Qty 6-8...$86.00 ea. -- Qty 9-17...$79.00 ea. -- Full Pallet holding (60) filters $65.50 each.
(1) Box of "High Efficiency", white, easy change out accordion type filters for Spray Booth exhaust. Lasts (2 - 5) times longer than most mesh filter media; evenly distributes air flow in booth, maintaing a consistent static pressure. -- Filter media is 3' high x 30' long (cut-to-size) 2-1/2" thick, (8) pleats per foot, with recommended air velocity of 100 - 200 FPM. Back-to-front loading with 6 Lbs/sq. ft. holding cap. Filtration efficiency at 150 FPM ranges from 97.8% - 99.8%. -- Price quoted is for (1) box delivered to your door. -- Qty 3-5 $87.00 ea. -- Qty 6-8 $82.50 ea. --Qty 9-17 $79.50 ea. -- Full Pallet holding 56 filters $52.40 ea.
Box of (40), 20" x 20" "Standard", white, easy change out accordion type filters for Spray Booth exhaust. Lasts (2 - 5) times longer than most mesh filter media. Evenly distributes air flow in booth, maintaing a consistent static pressure. -- Filter media is 2-1/2" thick and (8) pleats per foot, with recommended air velocity of 100 - 200 FPM. Filtration efficiency at 150 FPM ranges from 91 - 98.1%. -- Specific efficiencies: High Solids 97 - 98.1%, bake enamel 93 - 94.5%, fast dry enamel 96 - 96.9%, 2-component epoxies 91 - 93.5%. -- Sales price quoted is per box for 3 or more boxes delivered to your door
ANGELO CREMONA TZE 4000 4 m up-stroke Veneer Slicer with flitch pushers and MERRITT vacuum table. -- Now offered at a greatly reduced price!
$31,500
Apex Machine Group LS-TS 300 lineal sanding machine Set Up for HEAVY DUTY wire brush distressing or regular sanding. --Wire Distressing --Barn wood / Salvage board clean up --Antiquing --White wood sanding --Sealer scuffing --Brushing metal for lineal brushed finishThe Apex LS line of lineal sanders is designed for effective multi-sanding in one pass with a working width of 12" (300mm). The LS-TS sander has two top sanding heads with a motorized conveyor. Machine is designed to process the top, left and right sides of product in a single pass.The sanding units are adjustable in height, width, rotation and RPM to set them exactly to suit different shaped profiles and applications. The LS-TS lineal sander incorporates large diameter sanding heads to increase sanding dwell time to achieve aggressive whitewood sanding at increased feed speeds. All sanding heads are reversible and can be fitted with double sided abrasives to accommodate for multiple applications such as raw wood sanding, sealer / primer sanding or wire brushing/ distressing.Standard Features: ● Heavy-duty cast iron frame design ● Counter rotating large diameter sanding heads ● Conveyor belt feed with four spring loaded hold-down rollers ● Constant height of through feed ● Digital readout counter for sanding heads ● Four – 4" (100mm) dust extraction outlets ● All sanding heads are reversible ● Machine can easily be moved with pallet jack, fork-lift or rolled on casters ● 3 HP motors on top heads for wire brush applications ● Independent height adjustment on 1st & 2nd top heads ● Wire brush heads for distressing ● Nylon brush heads for distressing ● Aluminum hub with disposable sanding strips for smooth sanding Specifications: ● Thickness of Work-piece - 0" - 4", 100mm ● Conveyor Belt Width - 12"- 300mm ● Motor on top heads - 3 HP ● Motor on side heads - 1-1/4 HP ● Conveyor motor - 1 HP ● Speed of Spindles - 100 - 500 rpm ● Brush Diameter - 12" Top & side heads ● Feed Belt Speed - 10 - 50 foot per minute – variable ● 480 Volt / 3 Phase / 60 Hz Total amps - 20 ● Machine Weight 1,850 Lbs.INCLUDES:• Machine includes independent adjustment for the both top sanding heads for proper adjustability when running wire / nylon brushes• Comes standard with aluminum hubs and sanding strips
$1,450
Apex 20" Disc Sander --20" Disc capacity, SQUARE "D" Forward and reverse controls for disc rotation. -- 5 HP 1,800 RPM main motor. -- 10" x 22" manual tilting work table. Table tilts 45° up and 45° down -- Complete on a stand with work light.