Woodworking Equipment For Sale

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. EPDM covered applicator rolls, 6-1/4" chrome plated doctor rolls, upper elevator opening 0" - 6". -- Single speed 1.5 HP drive for 88 FPM, NEMA 12 enclosures. -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar.NOTE: Very Good overall condition, but rolls will need to be recovered, and Seller has discounted price to reflect this expense.

BLACK BROTHERS TOP AND BOTTOM 775- HOT MELT Glue Spreader with 32" working width.7-3/4" Heated Adhesive applicator rolls, with flow controlled by Chrome Doctor rolls. -- Single speed feed drive motor, operating at approximately 88 FPM. -- It has a 32″ width capacity and a 5-1/2″ thickness capacity. -- The doctor rolls are in very good condition. The price listed reflects that the 2 applicator rolls need to be re-covered. Or we can have them recovered for you for an extra cost and re-install. Please contact us with your specifications as we do not recover rolls until a machine is sold as these machines are very application specific. Meaning type of material which is usually silicone or a blend and durometer.This Model 775 has been cleaned and checked, and it heats up, and runs as it should.

BLACK BROTHERS 775-56 Top and Bottom Glue Spreader with Extra Tall Opening for SIP PanelsDescription & Specifications:1. Top and Bottom glue spreader2. Upper elevator machine opening to 12 - 1/2" opening3. Pass line-height 30"4. Variable speed drive by inverter 40 - 120 fpm5. Electrical interlock on upper and lower Nip Guards6. Operating control bars7. NEMA 12 electrical enclosure 575 Volt, 3-phase power8. Coating rolls rubber 7 - 3/4" dia OD, 14 TPI with 1/2" Cross Hatch Grooving.9. Doctor rolls chrome 6 - 1/2" dia ODThis is a 2007 machine but has never been put into operation and is ready to go, it has 575 volts, you may need a transformer.

BLACK BROTHERS 1205 Air Pod Press Overall 146" x 62" platen dimension with (3) individual top platens, side loading on 146" side. -- Motorized vertical daylight up to 30" -- (3) Individual platen zone controls for up to 5’ x 12’ press area, (3) 4’ x 5’, pneumatic top pressure via (48) 5-1/2" stroke air pods producing a maximum 50 PSI specific pressure. -- Air-assisted pop-up rollers in bottom platen for loading-and-unloading, pass line height for loading is 29".

Black Brothers 22D glue spreader Max working width 50"Max working thickness 3" 1/2 Hp, 230/460 volt three phase drive motor Table passline height 40" 7-1/4" diameter x 50-1/2" long top and bottom chrome doctor rollers 9" diameter x 50-1/2" long top and bottom rubber covered applicator rollers (Please note that the top doctor roller and top applicator roller is segmented) 11-3/4" long and 38" long top roller segments

Black Brothers 22-D-875-68 Top Only Glue Spreader with 68" working width, 8-3/4" dia. Smooth Neoprene applicator roller, 6-1/2" dia. neoprene doctor roll, top roll applicator only, upper elevator opening 0" - 4-1/2", REEVES variable feed drive 1.5 HP. -- Complete with: Electrical interlocks, and safety shutoff bars.

Black Brothers Top Only Glue Spreader with 56" working width capacity. -- 8 3/4" dia. Chrome applicator roll with Chrome doctor roll and flow is controlled by single hand wheel adjustment. -- 1-1/2 HP motor variable speed drive. -- Upper elevator opening 0" - 4-1/2" w/manual hand wheel adjustment. -- Includes: safety guards, electrical disconnect box and magnetic starter.

BLACK BROTHERS 22-D-650-32 Top & Bottom Adhesive Spreader; Top & Bottom Roll Glue Spreader with 32" capacity. -- 6-1/2" Rubber glue applicator rolls with 16 TPI Grooving, flow controlled by 4-1/2" Neoprene doctor rolls. -- Single speed feed drive motor - 88 FPM. -- Lower elevator opening 0" - 3-1/2". -- Complete with: Magnetic start and all guards and labels.

Black Bros 4 X 8 End Load Cold Press Capacity of 54? X 96? with a 37? thickness It has newer main pressure hoses. On the bottom you will find pop up rollers to aid in loading and unloading. The plates are flat and dent free.

BLACK BROTHERS - Cold Press Laminating Line (Complete)with: BLACK BROTHERS - APP PL: 5 x 12, 50 PSI End-Loading Fixed Opening Air Pod PressCurrent Line Setup: Infeed Scissor Lift; Panel Pusher; Panel Cleaning Brush; Glue Spreader; Stack building Scissors Lift; Laminate Rack over Conveyor; Stack Staging; Press Loading Conveyor; Cold Press. -- Station 1: Pneumatic Panel Feeder Panel Pusher feeds individual panels from side loaded (w/Forklift) Scissor Lift into Panel Cleaner. Photoelectric eye activates arm that pushes panel into Panel Cleaner. Pusher Arm: Feed panels into machine on demand. Switch: Remote mounting. Pass Line: 44"; 24" Stroke with 4' of adjustment: Feeds panels from 1/2 thickness, up to 250#, in lengths of 8', 10', or 12'; Controls on (Left or Right). NEMA 12 Enclosure with main power disconnect switch and over-current protection: 230 or 460 Volt; 3 Phase, 60 Hertz, 24 VDC Control Circuits. Dual Limit Switch Arrangement: Controls the Scissors Lift with "hand/auto" selector and a Barrier Guard to prevent double boardfeed. -- Station 2: Scissors Lift 36" Vertical travel foot operated raise/lower switch. 48" x 120" Plain deck with: 6,000 Lbs Capacity. Pin adjustable Edge Guides, mounted on SL and Anchor Clips for mounting. Transverse Conveyors with: Air brake to allow loading or unloading from side. -- Station 3: MIDWEST AUTOMATION - PC160: Panel Cleaner 63" Working width capacity; (2) spiral type cleaning brushes; 0" - 3" thickness opening; single end adjustment with roll opening (scale-type) indicator. Variable feed speed: 30 - 150 FPM with 1 HP - 1,725 RPM Drive; (2) 6" dia. infeed and (2) 6" dia. outfeed rolls; variable brush speed with 3 HP motor. - Equipped with: All guards, dust hoods, and magnetic starter. -- Station 4: BLACK BROTHERS - 775: Top & Bottom Adhesive Spreader; 68" width capacity Application: Apply water-based adhesive to top & bottom particle board, plywood, and MDF substrate. Upper Elevator: 0 - 4-1/2" Opening. Roll Opening Indicator: Shows opening between rolls in 0.001 increments. Riser Base: 44" Pass line height. Caster Arrangement: (4) Plain rigid casters with guide track and lock. Coating Rolls: (2) 7-3/4" Max. O.D.; 60 Durometer - Neoprene/SPR; Grooved: 16 TPI. Doctor Rolls: (2) 7" Max. O.D.; 100 Durometer - Ebonite; ground smooth single hand wheel Doctor Roll adjustment with mechanical digital readout. Electrical Interlocks on nip guard(s). NEMA 12 Enclosure with: Main power disconnect switch and overcurrent protection. 1-1/2 HP, Single speed with: 3" Reverse lockout 88 FPM. Pivoting Infeed Table. Operating hand wheels & controls: Parallel to the direction of flow on the right; motor on left end. Operating control bars. Liquid level control: FIBER OPTIC. Machine mounted double-diaphragm Pump: l" Ports

BLACK BROTHERS - 22-D-875-32, ...Top Only Glue Spreader.Capacity 32" Working width. -- 8-3/4" Dia. Rubber roll -- 6-1/2" Dia. chromed steel doctor rolls. -- Top elevator opening w/Readout -- Constant pass line: 36-3/4" -- Outfeed roller conveyor -- 7.5 HP MotorComplete with:1 Spare rollerNOTE: Machine is currently wired for 220v

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. grooved rubber covered applicator rolls, 6-1/4" chrome plated doctor rolls -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar. -- Top elevator style glue spreader, constant pass line --Main Motor 1HP, 3ph --Feed speed 88FPM --Thickness adjustment via manual hand crank

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. Grooved rubber covered applicator rolls, 6-1/4" hard rubber covered doctor rolls --Main motor 1.5hp -- Bottom roll adjustment -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar.NOTE: Currently wired for 460v

Specification from owner 2007 Black Brothers 775-56” Top and Bottom Glue Spreader with an extra-large 12.5” opening designed for SIP (structural insulated panels) manufacturing. This machine is brand new and ready for immediate delivery. 575V, 3PH

48" wide Black Bros UV Curing Oven

BLUM - Mini Press: Hinge Borer -- Tabletop "Mini Drill" unit for BLUM Hinge Boring; 1.5 HP (1.1 kW) - 2,450 RPM drill head assembly for hinge cup boring. -- Head assembly rotates for several hinge & drawer system boring patterns; pneumatic drill cycle with air blow-off. -- Includes: 48" x 24" Tabletop. -- Machine also used for line boring by purchasing an auxiliary BLUM spindle head; not included. -- Complete with: 3-Drawer mobile storage base for all hinge components.

BMT B 700 Pin Router referbished in 2010

BOARKE - BKM-43103RRK: (3) Head 42″ Wide Belt Sander (3 NEW Drums)43" Width cap.: Drum, drum, platen.Head Configuration1st Head: 30 HP; 10″ Helical grooved drum.2nd Head: 25 HP; 10″ Helical grooved drum.3rd Head: 20 HP; Helical grooved (idler) with a platen. Specifications -- 42″ Width capacity; 5″ height capacity running. -- 43″ X 103″ Abrasives. -- 1st Head: 30 HP; 10″ helical grooved drum. -- 2nd Head: 25 HP; 10″ helical grooved drum. -- 3rd Head: 20 HP Helical grooved (idler) with a platen. -- 1st & 2nd Heads: Dial indicators to dial in abrasives; has optional 5 HP vacuum feed bed.Equipped with & Features: -- Feed: Variable from 7 - 45 FPM via a 2 HP motor; VFD for speed control. -- Feed Mat: Thick; with usual crazing, but plenty of life. -- Elevation: Handled by a 1/2 HP motor. -- Machine includes: Digital readout; touchpad control combined with auto thickness calibration unit on the right.

Manufacturer’s Specification ( to be confirmed) - With its powerful 3 HP motor can delivers the performance professional demand. - Coupled with an industrial quality eccentric oscillation mechanism that delivers more efficient sanding, less tendency to burn and less belt loading. - Heavy duty spring system allows easy adjustment for the front aluminum table for full use of the abrasive surface. - Aluminum auxiliary contour table allow use of 4” idler roller as a drum sander. - 9” Dia. Drive drum, 4” Dia. Idler drum. - 9-1/2” x 48” cast iron platen with graphite pad. - Rugged bearing – assisted belt torsion devise.. - Aluminum table travels 8” and tilts – 5 to 45 degree. - Dual 4” dust ports. Belt speed: 4200 RPM - Sanding belt oscillate distance: 1/4” (6 mm) Motor5HP / 220V / 60Hz Belt Size230 x 3520mmn Frint Table Size (L x W)1210 x 300mm Dust Port 4”

BOARKE (HOLZ-HER) - BKM-37RK2: 2-Head Wide Belt Sander37" Width cap. Drum & Combination Head.Head Configuration1st Head. Rubber-covered contact roll; 6-1/4" dia.; 20 HP motor.2nd Head. Combination head with: 6-1/4" Dia. rubber covered contact roll (50-Shore); 3-1/8" wide finishing platen; 15 HP motor.Specification -- Abrasive belt size: 37" x 75". -- Air tensioning & electronic abrasive belt tracking. -- Conveyor belt feed with: 2 HP Variable feed drive. -- 9 - 45 FPM Feed speed with inverter.Equipped with & Features: -- Infeed & outfeed rubber covered holddown rollers. -- 1/8" - 7" Max. motorized thickness opening. -- LED Readout thickness. -- Part "over-thickness" protection. -- Automatic conveyor belt tracking. -- Emergency stop button. -- Motor load meters. -- Magnetic controls.NOTE: Very clean machine; low hours: Only ran prototypes; replaced with 3-head machine for production.