Northfield For Sale

SUPERFICI Compact Spray Automatic Spraying Machine; System is ideal for medium to high volume production. Product: Kitchen cabinet components, panels, furniture components, doors, etc.Coatings: TBDGENERAL EQUIPMENT FEATURES:Pass-line Height: 900 mm (35-7/16")Operating side: RH, as viewed from inlet of line.Work piece Dimensions (Approx.):Min. - max length: 300 mm - 4,800 mm (12" - 16')Min - max width: 25 mm - 1,300 mm (1" - 51")Min - max thickness: 3 mm - 80 mm ( 1/8" - 3-1/8" )Max. weight: 2.2 Lbs per sq ft maximumSpeeds:Mechanical Speed: 2 - 6 m/MinAvg. production speed: TBD based on coatings and Drying system used. -- Photocell Reading System to detect the incoming workpieces profile and the electronic control to adjust the spray profile of the parts. The guns will trigger only when the parts are present. -- Closed belt conveyor system mounted on an open structure for easy removal. The belt conveyor is made of a special material to work with all types of stains and paints. -- Reclamation system for spray lacquer, varnish, multicure (UV) and water base solvents. Patented lacquer recovery system for recovery and cleaning of the conveyor belt; the system is mounted on trolley that is extractable from the machine for easy maintenance. -- A double arm reciprocator driven by inverter controlled motor and sliding on high precision guide rails. -- The two arms are equipped with guns holder supporting up to max four (4) guns each arm with two active lacquer circuits. -- Pressurized spray cabin with access windows from both sides; filtering roof intake celling in the spray cabin with blowing fans on the top of the roof. -- Exhaust system with double stage paint filters over exhaust ventilator.Technical Specifications: -- Mechanical speed: 2 - 6 MPM (6-1/2 - 19-1/2 FPM) Avg. - Typical Production speed: 2 - 3 MPM (6-1/2 - 10 FPM). -- Working width of 1,300 mm (51"), max. part thickness 80 mm (3-1/16"), Pass through working height above floor 900 mm (35-1/2"); -- Exhaust air volume of 7,000 cbm/Hr. -- Compressed air consumption (with guns) 1,500 N1/Min. Approximatley.Utility Connections:Voltage: 480 V / 3Ph / 60 Hz + groundCompressed air: 6 bars (90 PSI)USED LAMINAR DRYER, is available with this sprayer at an additional cost (not included in this price)CEE standard execution. Conveyor executed according to the European norms, to be positioned in a safe environment (not classified as an area with risk of explosion).

SUPERFICI UV Dryer with Bar Conveyor (TU166/76):"Twin Angle Mounted" Ultraviolet 2UVM1 modules; (2) 77" 300 Watt, 2,000 mm 120 W/cm power individual lamps with variable power output control. -- (1,381) UV Hours on Lamp Module #1, (1,306) Hrs on Lamp Module #2; Bulb #1 with (126) Hrs, Bulb #2 with (68) Hrs. -- Inverter controlled variable speed from 20 - 60 FPM; (1) 2.2 kW exhaust fan per lamp; digital control interface with individual controls for each UV lamp. -- 60" L x 83" W x 75"; TU166/76 Conveyor, 236" L x 83" W x 8" H. -- Min./max. part dimensions: Min. length is 12", max. length is 138", min. width is 1", max, width is 63"; min. thickness if 0.118", max. thickness of 3.15"; max.. individual part weight of 175 Lbs; max. overall part dimension is 138" L x 63" W x 3.15" H.Excellent Physical & Mechanical Condition: All units of the Flat Line were made to order by SUPERFICI in 2012 and installed in the spring of 2012. --The UV Lamps have been recently replaced; Lamp #1 has (126) Hours of use, and Lamp #2 has (68) Hours of use.Includes complete original factory manuals and keys.NOTE: The line has been taken down and is in storage. It is very well-kept and ready to ship !!

Manufacturer’s Specification - Maximum Width: 24” - Brush: 9"-11" Typical Diameter - Speed: Ranged Variable, 400-1200 rpm Brush - Motor: 5 HP, 220 Volt, Single Phase - has (1) broken caster

TAKEKAWA - RG-30S, ...Straight Line Rip SawSpecifications: -- 15 HP - 5,000 RPM Belt driven arbor, overhead arbor design. -- 1-1/4" Dia. arbor. -- 12" Dia. max. blade cap., 2-3/4" max. depth of cu.t -- 12" Min. part length. -- Throat clearance to the right of blade 26". -- Table size: 74" Long x 38" wide; 2 HP step feed drive, 33 - 66 & 131 FPM.Equipped with and Features: -- Automatic chain lubrication. -- Top pressure system with spring loaded rollers. -- Adjustable rip fence. -- Antikickback fingers. -- Push buttons and magnetic starters.

16" Blade cap., 3-3/4" max. cutting height, 5 HP - 3,600 RPM direct drive motor, arbor tilts 45ø, 44" x 40" cast iron table size, table with miter gauge slot. -- Complete with: Rack & pinion fence and large hand wheels for easy adjustments.

TANNEWITZ - XJ, ...Table SawSpecifications: -- 5 HP - 3,600 RPM Fan cooled motor, 1" right tilting arbor Table Saw with a 1-piece main table; table size 42" wide x 44-1/2" deep. -- Base formed from hot rolled steel of 5/16" thickness & welded into (1) solid unit; 10" dia. handwheels for easy adjustment of tilting, raising & lowering of arbor. -- Complete with: Extended rack & pinion adjustable rip fence for greater ripping capacity; left- & right-hand T-slot miters. -- 16" Blade dia., 4" dado width cap.; 4" cut depth at 90°; 3" cut depth at 45°. -- Equipped with: Taper pin miter with micrometer adjustment on fence, magnetic controlled off switch, and 6" dust outlet with auxiliary rear opening for easy access. -- Power safety electrical breaker box included. Please NOTE: No blade guard.

Runs good and is still in operation Hooked up to 460 Table Extension has been repaired Main table has almost zero wear on it.

Capacities: 11” minimum length 98” maximum length 1” minimum width 32” maximum width 5/8” minimum thickness 3” maximum thickness with a conversed glue spreader(model 30J)

--In Auction: https://exfactoryauctions.com/Detail/CR-230068/event/A122024$1 --No Reserve!-- TAYLOR 800036 7' W 12-Section Semi-Automatic Pneumatic Clamp Carrier, with Flattener & Tightener Equipped with: (71) 32” Cap. Clamps, with 4-5/8” W x 3-1/2” H Jaws. Air motor drive. Dual foot pedal control. Complete with: Pneumatic Panel Flattener. Pneumatic Clamp Tightener.

TAYOR 16-Section Clamp Carrier 20.5' width cap., (7) clamps per section (128 clamps total). .48" max. clamp opening clamps with 4-1/2" X 3 1/4" jaw height (128) Rocker plates 4" X 6" @ 80-1706 (purchase in June 2024)Complete with: -- Semi-automatic clamp tightening, -- (2) Air drive carrier rotation. -- (2) Pneumatic panel flattener -- OAL approx. 24' X 14' X 12'Note: The buyer will be responsible for tear down and loadingMachine model CC 20,5-16-481

TAYLOR - 20-Section: Clamp Carrier Specifications -- 8-1/2' Width cap. -- 39" Max. clamp opening; 2-1/2" Jaw height. -- Approx. (4) clamps per section.Equipped with: -- (75) Clamps total. -- Pneumatic tightener. -- Pneumatic panel flattener.Complete with: -- Air drive carrier rotation. -- I-Beam chain assembly.NOTE: Already taken down.

TAYLOR 40 Section Clamp Carrier.Specifications: -- 40-Section, 8-1/2' width capacity -- Average 4/5 clamps per section (175 clamps total), all with 32" max. clamp opening. -- Equipped with (175) clamps plus a pallet of spares that require repair, 32" clamps with 2-1/2" high jaws .Complete with: -- Heavy Duty Drive for rotation,& clamp tightening. -- Foot pedal control. -- Includes a glue applicator.

JLT Clamp - 713A-8-LCS: (8) Section Large Capacity Door ProLarge capacity 8-section Rotary Door Clamp for the medium to large cabinet shop. Produce up to (400+) cabinet doors per day. -- Each section includes: 38" x 96" Max. clamping capacity with: 2-1/2" High jaws; (4) vertical clamps; (2) horizontal clamps. -- Clamp & square multiple cabinet doors with vertical center rail: (2) 38″ x 45″ Doors side by side Double Door Clamping. -- Includes: Heavy-Duty; pneumatic drive for rotation; pneumatic clamping; squaring assembly.Actual model: # 713A-8S-129W-68H-80D-NS-M-LC-L-M2

TAYLOR - 6-Section: Pneumatic Clamp Carrier6-Section x 10-1/2' width cap.; (36) total clamps; 30" opening on clamps; 3-1/2" high jaws; includes: Pneumatic rotation; tightening; panel flattening. -- Overall assembled dimensions: 9-1/2' Deep x 13-1/2' wide x 9' tall.NOTE: Teardown not included.

Tregarne Wood Welder New in Box

TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.

Thermwood C42 CNC Router (2) 5'x5' Tables It has 2 large routers, 4 smaller routers, and 2 aggregate heads in the turret Travainni Vacuum Pump Note from Seller: Includes two shaper heads that are not mounted into the turret and one pneumatic drill head that is not mounted into the turret. I also have one seat of Microvellum cabinetry program that I will transfer to you along with the purchase.

MLS Number 11772789 2015 Thermwood FB53-510 CNC Router Very good working condition Low hours. Used for only 1 year. Excellent condition Moving gantry, fixed table, roller hold down CNC router Designed to machine low profile sheet materials(MDF, plywood, particleboard) Uses Microsoft Windows 10 Professional operating system

Thermwood Model M90-510 5-Axis CNC Router Less then 20 hours on this system - only installed and training. Ready to be removed!

Table Size: 5' x 10' Spindle: 18 HP HSD Max. Spindle Speed: 18,000 RPM Number of Axis: 3 Gantry Clearance: 10.5? Z-Axis Stroke: 6? Power: 460 V, 3 Phase Approx. Shipping Weight: 12,000 Lbs. Approx. Shipping Dimensions: 7' W x 16' L x 8' H Equipped With: Roller hold down 5 position Typewriter Arm Style Tool Changer Daylight touch off sensors Equipped for Vacuum Hold Down Windows 2000 Operating System