Murphy Rodgers For Sale

Homag Centateq N300 CNC Router 5 X 10 Infeed system Outfeed table Boring block (2) Vacuum Pumps Main Hours: 1,101 Secondary Hours: 370

Homag Centateq N300 CNC Router 5x10 Table Offload conveyor Schmaltz overhead gantry system

Homag D-200 Drill & Dowel Inserter

- Min. panel height 0.47 inch - Max. panel height 1.57 inch - Min. edge thickness 0.01 inch - Max. edge thickness 0.24 inch - Max. forward feed speed 82.02 ft/min - Top pressure with rubber belt - No. Panel Sizing / Milling units 2 Pre-milling unit - Lamps to preheat the side of the panel - Edge coil magazine - Gluing system - glue pot for EVA hot melt glue - premelter for EVA hot melt glue - QA65 - Roller set to press the edge - no. pressure roller 7 - with positioning by NC No. Edge Processing Units 6 First Processing Unit - End trimming Constructor model HL81 - no. motors 2 - with positioning by NC Second Processing Unit - top and bottom rough trimming - no. motors 2 - with positioning by NC Third Processing Unit - Multi Function trimming and corner rounding - Constructor model - FK11 - no. motors 2 - with positioning by NC Fourth Processing unit - edge scraping - with positioning by NC Fifth Processing Unit - glue scraping - with positioning by NC Sixth Processing Unit - buffing - no. motors 2 Spray unit Control system Power Touch

Weeke Model Optimal BHX050 Vertical CNC Machine 8 Vertical Drilling Spindels 2 Horizontal Spindle in X-Direction 1 Horizontal Spindle in Y-Direction Grooving Saw in X-Direction 1 Powerful 5kW ETP 25 Routing Spindle Vector Speed: X-30M/Min Y-30M/Min Z-15M/Min

HOMAG KAL 310/4/A3/S2 Edgebander (w/Pre-Milling): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

HOMAG DRILLTEQ V-200 CNC MACHINING CENTER (VERTICAL/W/BORING): -- Specifications: Flexible "Vertical" Machining Center with "BORING": Uses less than 5 sq. meter of valuable floor space in addition to an innovative panel handling system. -- Working Cap.Max. workable part size for "X" axis is 120" (3,050 mm); "Y" axis 33.4" (850 mm); max. part thickness 3.1" (80 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.75" (70 mm); min. part thickness of 0.31" (8 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning SpeedThe "V-200" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axis & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit(1) 3 HP (2.3 kW); Variable speed from 1,500 - 7,500 RPM motor; (13) independent spindles with: (8) spindles in "X" axis & (5) spindles in "Y" axis.(6) Horizontal spindles with (2+2) in "X" axis & (1+1) in "Y" axis; boring block has "QUICK CHANGE" spindle system. -- Operator Interface:HOMAG "POWERTOUCH" + Windows + WoodWOP Operating System; "IntelCore 2 DUO" Processor.21" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:(1) "X" Grooving Saw; 9,000 RPM, max. saw blade dia. 100 mm.(1) 12 HP (9 kW) Electro Spindle router with manual Quick-Change adaptor; variable speed from 6,000 - 24,000 RPM. -- Actual Model is: HOMAG DRILLTEQ V-200 OPTIMAT BHX 055.

Homag Optimat NBP084/ Vantech 480 4x8 Bed 12 HP Spindle (replaced in 2019) 7-Position Boring (3) Vacuum Pumps Clean Machine

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

Hunton Limited Punch Grinder

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

2004 Hymmen Proficoater 60" Roll Coat Line - Model ULX-S: Includes spare drum and lights SCMI Finish Sander

IMA Combiform I/R75/1260/V

IMA - HKA EXPERT CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. Designed for straight or curved (contour) edgebanding:0.5 - 3 mm Edgebanding thickness; 16 - 45 mm (0.63" - 1.77") panel & banding height; 23 - 45 mm (0.9" - 1.77") min. strip width; 100 mm (3.9") min. panel width; 250 mm (9.8") min. strip length. -- Equipped with: Versatile glue head that can be fixed to 1-side of the table to allow the operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine, via foot-pedal control. -- Work Table:32" (800 mm) Dia. coil dispensing table, large 813 x 914 mm (32" x 36") High-Flow Phenolic worktable surface;Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head (hot melt) glue pot" with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA 500L Edgebander Will need a new touch screen control and calibration.

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.