Woodworking Equipment For Sale

Unit has less than 20 hours. Has not been run in several years. Has slight shipping damage on the hood. [email protected]

Weinig Powermat 700 Eagle, 1-1/2” spindles. Measuring Stand, tooling and spare parts as pictured

Weinig Profimat 22 N Moulder Work ready

WEINIG PROFIMAT 23 Feed Through Moulder;(6)-Heads (B-R-L-T-T-B), working cap. 9-1/16" x 4-11/16".Specifications: -- Spindles 1-1/2" dia. with cutterhead speed of 6,000 RPM. -- Feed System & Features: variable feed speed from 20 - 78 FPM, powered by a 5.5 HP motor. -- Receding chip breaker at top spindles. Side pressure opposite right spindle; spring-loaded with (2) rollers; driven outfeed roller in bed. -- In-feed straightening table 2 M (78"), side pressure roller mounted to in-feed table. Note: Bare Machine: No dust manifold or tooling.

Weinig Unimat Gold - 6-Head Machine Weinig Rondamat R960 Grinder Includes: Tooling and approx (200) profiles from tool room

1978 Weinig 7 Head Moulder S/N 2816/2248

Weinig U22N Moulder 7 head Mid 80s Freshe rebuild

270 TON WEMHONER 110"; L TO R X 59"; F TO B DOWN-ACTING HYDRAULIC PRESS: MODEL KT-M-15/28-240. CLEARANCE BETWEEN FRAME IS 126"; L TO R X 37"; F TO B --. NOMINAL BED IS 110"; X 59";. -- FOUR CLAMP CYLINDERS THAT ARE SINGLE-ACTING; APPROX 8"; BORE; 6"; DIA RODS; APPROX 10"; MAX STROKE. -- ONE CENTER TRAVERSING CYLINDER THAT IS APPROX 3"; BORE WITH A 1.75"; DIAMETER ROD (APPROX 16"; MAX STROKE). -- MAX DAYLIGHT IS APPROX 16"; --. APPROX 28.5"; OPERATOR HEIGHT. -- GUIDED WITH ROLLERS AT EACH CORNER AND TWO GEAR & RACK GUIDES. -- SLIDE AND BED ARE 4"; THICK. SELF-CONTAINED HYDRAULIC SYSTEM: -- TWO RESERVOIRS THAT ARE APPROX 14 GALLONS EACH. -- 4 KW MOTOR (APPROX 5 HP; 1800 RPM; 440 VOLTS; 9.15 AMPS). -- HAWE PUMP (TYPE R60A; MAX 350 BAR); ETC -- APPROX SPEEDS: 99 IPM FAST DOWN; 2.0 IPM PRESSING ADJ; 99 IPM FAST UP. -- NO ELECTRICAL CONTROLS. -- APPROX OVERALL DIMENSIONS: 146"; X 65"; X 96"; TALL --. APPROX 30,000 POUNDS

Wemhoner Variopress

West Salem model 2420GR1-H wood grinder/hog 480 v Bottom discharge No screen - machine has breaking bars Disconnected and ready to ship

WESTERN PNEUMATICS HEAVY DUTY FINGER JOINTER WITH THE FOLLOWING EQUIPMENT & FEATURES: -- Right & Left Shaper Section: Thickness Capacity: 3/4" - 2" maximum; Width Capacity: 1-1/2" - 8" maximum; Length Capacity: 5" min. - 36" maximum; -- (2) Scoring Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Trim Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Shaper Spindles are hydraulically powered; direct driven @ 3,600 RPM by -- (1) 60 HP Hydraulic Power Unit with (1) cartridge unit per spindle. Hydraulic conversion was performed during the first year of operation. -- Western's 2-1/2" wide feed chain with lugs on 9" centers; 15 HP variable speed drive with up to 120-lug per min feed speeds; with angle transfer conveyor, air bag pressure head with quick-change feature & brush hold-downs -- APQUIP Extrusion Type Glue Applicator complete with mixing system. Currently arranged for 3/8 finger joints including (4) 3/8" glue combs -- Manual Corner Transfer to the assembly section. (allows for inspection and rejection of blocks for poor joint quality, missing proper glue spread, etc. prior to going into assembled boards) -- 12' Pre-Assembly Infeed Conveyor with feed speed ramp up/down; with side alignment rolls and dual top and bottom pre-assembly rolls -- Flying Cutoff Saw operating from below -- Assembly Press: 20' board capacity with hydraulically powered press -- Automatic Cycling Assembly Section: Feed speed varies automatically from 50 to 200 FPM, depending on incoming block lengths. Boards advance through the Cutoff Saw to a moveable limit switch where they are cut to length with a bottom-mounted 7-1/2 HP Flying Cutoff Saw arranged for continuous non-stop assembly. The cut to length board drops down into the squeeze chamber while the next board feeds out and above the preceding board where it is cut to length. Pressed lengths are pushed out onto material outfeed arms by the following board

WHIRLWIND 1000 R 14” Right-Hand Semi-Automatic Pneumatic Upcut Saw Specifications: Cutting cap. 2-3/16" x 8-1/4". Work area 12” x 22” x 36-1/2” H. Arbor dia. 1”. Blade speed 3,450 RPM. Cycle speeds 5 - 90 Cycles/Min. Equipped with: 5 HP - 1,740 RPM - 208 - 230/460 Dual voltage motor. 20-1/2” L x 1/2” H” Aluminum fence. Built-in foot pedal control. Complete with: TIGERSTOP “TS-10” 10' L Automated Material Pusher/Stop, S/N 1016705, with Overall length 12', 10” W x 12’ L x 36-1/2” H, Solid pusher/infeed table, 14-1/2” W x 10’ L x 36-3/4” H Solid outfeed table with 12’ L x 1-1/4” H Aluminum fence with scale, TIGERSTOP “CON5” Controller, with LCD Display, Touchpad, “VPK2” Software package (Optimization, Download, & Ethernet Connection), & TIGERSTOP “AMP5” Amplifier. Saw with Pusher/Stop Dimensions: 318” x 27” x 63” H. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Whirlwind Undercut Saw with Tiger Stop Fence

Whitney 105 Planer 24" Planer Used daily in current shop.

Whitney 105 Planer 24" Planer Used daily in current shop.

Williams 125 HP Hammermill 230/460 3-phase

Williams 125 CJS1 Hammermill

Manufacturer’s Soecification Feed Type:0-19 fpm, variable feed Motor:2 HP (3450 rpm) Voltage:240V Maximum Profile Depth ¾ inMinimum Stock Length 9 inMaximum Profile Width 6 ¾ inMinimum Stock Thickness ¼ in Maximum Height Above Final Cut 3/16 in Maximum Stock Thickness 8 in Planes 7 in WideOverall Machine Dimensions:28 inL x 22 inW x 50 inHWorking Height:35 in

William & Hussey "W-7S" Moulding Shaper -- Specifications: 17-1/4"x 14" Table size, 2 HP main motor, 2-knife cutter head, 3,450 RPM spindle speed, 7" max. cutting height, 1/4" min. thickness 3/4" deep max cut.. Max moulding cap. 7" wide, max. planning cap. 7" wide. -- Complete with: Dust hood outlet, electrical disconnect, and mounted on fabricated steel stand w/casters, Multi-pass