Woodworking Equipment For Sale

TIMESAVERS - 1311-13-1: Single-Head Wide Belt Sander1-Head; 37" cap.; 0 - 5" opening (33" - 38" pass line). -- Combination head with: 4-3/4" Contact roll & 2-1/2" finishing platen; 15 HP motor; 37" x 60" abrasive belt; disc brakes on main motor; centralized control panel. -- Features: Digital thickness readout; double infeed & outfeed holddown rollers; variable feed speed from 20 - 40 FPM; hour meter; main motor load meter/watt meter. -- Includes: Dial indicators on drums/platen; auto setup device; motorized lift; 13" infeed loading area; (4) bed jacks; quick release outboard support; through-beam abrasives belt tracking; infeed stop bar; UL listed controls.NOTE: Extra Sanding belts included.

Timesaver - Series 1300: Wide Belt Sander (3) Heads43" Width cap. drum; drum combination head.Specifications -- Dial indicators on drums/platens. -- 8" Drums. -- 5 1/2" Dia. on combination heads. -- 2-1/2" Width platen on combination head. -- 75" Abrasive belt length. -- 0 - 5" Opening (33 - 38" pass line).Equipped with & Features: -- Disc brakes on main motor. -- 20 - 45 FPM Feed speed A/C. --Auto set-up device. --Motorized lift. -- 14" Infeed loading area. -- Quick release outboard support. -- Through-beam abrasive belt tracking. -- 15" Minimum part length. -- Emergency stops at infeed and outfeed location.

TIMESAVERS - 2321-23-21: Planer Sander (2) Heads2-Head; 36" width cap.Specifications -- 1st Head. 6" Dia. Helical head with: (6) Spirals of 4-sided carbide inserts; 25 HP motor. -- 2nd Head. Combination head with: 5-1/2" Dia. contact roll and 2-1/2" wide finishing platen; 20 HP motor; sanding head with 37" x 75" Abrasive belt with "POSI-TRAK" electronic tracking. -- Dial indicators for height adjustments. -- Conveyor belt feed with Variable feed speed 20 - 45 FPM; automatic conveyor belt tracking. -- Anti-kickback fingers on infeed; planer head with sectional infeed shoe and double hold-down rolls on outfeed; double infeed and outfeed rubber-covered hold-down rolls on the sanding head. -- Motorized part thickness adjustment: 0" - 5" With mechanical digital readout. -- Minimum part length: 15"; Pass line height: 33" - 38". Complete with: -- Controls mounted on belt loading side; air activated caliper disc brakes on all heads; load meters for each head; 14" infeed loading area. -- Dust extraction: 3,500 CFM; compressed air usage: 3 CFM @ 90 PSI. -- Total load amps at 230 Volts: 145 Amps.

TIMESAVERS - 352 HDA, ...Abrasive Planer/Sander2-Head, 51" width cap. Heavy Duty Sander. -- 1st Head: Smooth steel contact roll, 11-1/2" dia., 75 HP motor. -- 2nd Head: Spiral Grooved hard rubber contact roll (11-1/2" dia.) , 75 HP motor; 52" x 103" abrasive belts (6,300 & 4,300 SFPM) with POSI-TRAK electronic tracking. Equipped with: -- Heavy-Duty solid rubber (no vacuum holddown) feed belt for Heavy-Duty operation. -- Motorized part thickness adjustment, 0" - 6" opening. -- 38" - 32" Conveyor height passline with MITUTOYO LED readout, conveyor belt feed. -- 5 HP Variable feed speed from 20 - 60 FPM, smooth rubber conveyor belt. -- Infeed & outfeed spring loaded holddown shoes, infeed emergency stop bar, anti-kickback fingers on infeed. -- Disc brakes on sanding head motors, 18" infeed load area, and motor load meters on sanding heads.

Dust Collection System

Reconditioned Torit 156RF10 baghouse

TORREDA HIDROPAL-1400 COPY LATHE

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Custom Ceiling / Flooring Table Table Size: 32' x 6'9" to 14'3" Table Operated by Both Push Button and Key Fob Controls Floor can be built manually on the table Clamping Stud Locators at 16" & 24"

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

40? deep X 87.5? wide capacity. The Maximum opening is 49.5? and the pods will extend 9.5? for a minimum opening of 40?. The press is rated to 100 PSI and has (1) pod short of 100% pod coverage. That being the center bags are staggered. There are spring loaded bed rollers to aid in loading and unloading. The top and bottom plates are dent free and no air leaks This fully functional machine has been fully cleaned and checked and is ready to work..

TYLER 703 Power Pod Cold PressTyler Air Pod Press with a Platen dimension of 40″ Wide X 87-1/2" Long. -- The Maximum Daylight Opening is 49.5″, and the pods will extend 9.5″ for a minimum opening of 40″. -- The top and bottom plates are dent free. -- The press is rated to 100 PSI and has (1) pod short of 100% pod coverage (being that the center bags are staggered). -- There are spring loaded bed rollers to aid in loading and unloading. .This machine has been cleaned and checked and there are no air leaks.

--In Auctions; https://exfactoryauctions.com/Detail/DL-230113/event/A122024$1 - NO RESERVE -- TYLER French-Type Dovetail Machine Equipped with: (2) 14-1/2” x 17” Tables. (2) 2 HP Routing heads for mounting of drawer sides. (1) 2 HP Grooving head for drawer bottom dado, (2) 2-Spindle Vertical boring heads for drawer hardware. (2) Pneumatic hold-down clamps

UHLING HP-3000 CASE CLAMP (SINGLE-BAY): --Specifications:Clamping Capacity: 55" L x 96" H x 24" D; large enough for multiple boxes. Offers versatility, quick 30-second setup or changeover. -- Pressure Elements:(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; position them effortlessly and let go. The counterweight keeps them in place; no need to secure them! -- Air Pod Stroke:3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical Beam:Moves easily on roller bearings with pneumatic carriage locks; (4) small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam, so it is always where it is needed; single-lever lock-or-unlock control & front/rear pressure selection. -- Counter Support by:Solid laminated panel opposite to pressure bars.

UHLING HP2000 Case Clamp (Pneumatic)Offers a compact, quick and easy-to-use Case Clamp.Specifications: -- 50" x 42" x 24" Clamping cap. that can handle 80% - 90% of your case good needs. -- (2) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks. -- Single lever lock or unlock control and front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access operator's control panel that is mounted on the vertical beam.

UHLING HP-4000 ... is a versatile, quick and easy-to-use Case Clamp.Specifications: -- 100" x 50" x 24" Clamping cap. that's UHLING's most versatile Clamp ever. -- (3) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars and (2) vertical, easy adjustable dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks (considered to be the fastest 2-axis Clamp on the market). -- Single lever lock-or-unlock control and front/rear pressure selection. -- Solid panel counter support that is opposite the pressure bars. -- Easy access operator's control panel that's mounted on the vertical beam. -- Approximately (30) Sec or less changeover time. -- Options: Additional dual pod pressure bar assembly for vertical or horizontal.

UHLING HP-3000 Case Clamp ... offers versatility, quick (30) second set-up or changeover. -- Clamping Capacity, 55"- L x 96"- H x 24"- D, that's large enough for multiple boxes. -- Pressure Elements, (4) horizontal @ with (3) individual air pods, counter-weight balanced, position them effortlessly and let go, the counter-weight will keep them in place, no need to secure them! -- Air Pod Stroke, 3-1/2" with individual controls for each air pod set. -- Vertical Beam, moves easily on roller bearings with pneumatic carriage locks. -- Operator Control Panel, mounted on vertical beam, so it is always where it is needed, single lever lock-or-unlock control & front/rear pressure selection. -- Counter Support, by solid laminated panel opposite to pressure bars. OPTIONAL: Top Clamping, removable top pressure element for applications such as a vertical center partition or similar needs, removes easily if not needed. Add $ 1,000.00 to standard machine price.CUSTOM:HP-3000 F, ... comes with a "Solid Floor" for easy clamping of upper cabinets, add $ 1,000.00 to standard machine price.HP-3000 M, ... clamping capacity, 60"- L x 96"- H x 36"- D, that's large enough for deep commercial Case Goods. Please call for pricing.