|
STROB GRINDER FEED W-725
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
Capital Knife Grinder
Equipment Location:Forks, WA
LPS Equipment & Acquisition Co.
731-986-4351
|
|
GOECKEL G 65EL Automatic Straight Knife Grinder;Working length up to 5,080 mm (200") and 254 mm (10") for either planer or chipper knives. -- Construction: Welded in cell design. Guideways hardened and ground solid ways. Machine table electromagnetic with rotating chuck. -- Downfeed system: Servo variable speed down feed with impulse feed; end-end and rapid positioning. Feed rate 0.0002 ~ 0.02 mm/Min. -- Carriage/Head: Servo controlled variable speed carriage drive, 0.02 ~ 30 m/Min adjustable via potentiometer. Grinding motor 40 HP (30 kW) with high precision bearings, tiltable for cross and radial grinding with 14" tool diameter. -- Controls: Programmable digital display and electronic hand wheel. Counter for counting finish passes. Automatic grinding cycles and wheel advance. -- Equipped with: 14" Nut inserted ring wheel flange, motorized 10” wide x 200” long magnetic table with rotation of 180°. Magnetic segmented chuck performs a variety of grinding operations. Table has built-in hood; wheel dresser is accurate and accessible to the operator. -- Grinding tolerance 0.005" per meter over full set of knives. Grinding wheels are changed via a bolt flange.. Automatic sizing units with wheel wear compensation for wear. Retractable front stop bar system. Coolant filter tank with two pumps. -- Comes with: Service manual, operating manual and electrical diagrams.Owner states that the magnetic table is in good operational condition, machine will be available in August 2018.
Equipment Location:SOUTHWEST
Bob Dykstra
800-374-5009 ext:378
|
|
HANCHETT SIZE 48 TYPE DN KNIFE GRINDER S/N 8221
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
Hanchett 38" Knife Grinder S/N 315
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
56" GRINDER
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
Hanchett Size 110" VKF Table Knife Grinder S/N 65
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
MVM - GM 1000, ...Straight Knife Grinder.For straight knives up to a 39" in length: ideal for Planer and Chipper knives. Head speed: Automatic head travel with speed up to 33 FPM. Automatic wheel down feed can be set per pass and for total down feed.Grinding Motor: 2 HP Grinding motor with 16 mm spindle/shaft. Grinding chuck tiltable 0° to 90°, and grinding head tilts +5° to -30°. Chuck clearance to wheel is 1.2" and chuck width is 3-1/2".Coolant: Heavy Duty flood coolant system with static magnetic filter. Chuck: Newly Rebuilt Magnetic T-groove chuck to stack grinding of knives with step blocks. Head travels on hardened and ground replaceable wear strips and head travel guides.NOTE: Machine is in EX-FACTORY's "Zeeland, MI" Warehouse and Repair Facility. - Thoroughly checked out and ready to ship!
Equipment Location:MIDWEST
Bob Dykstra
800-374-5009 ext:378
|
|
MVM AF 2000 Automatic Grinder for straight knives up to a 80" (2000mm) in length for planer, veneer and paper knives. Stepless variable speed carriage with travel speed up to 60 FPM (20 meters/min). -- Automatic wheel down feed can be set for: per pass and total downfeed. -- Grinding motor 8.5 HP (6.3 kW) with 16 mm bore. Grinding chuck tiltable 0 to 90ø. Chuck clearence to wheel 4.3" (100 mm). Chuck width 4.7" (120 mm). -- Heavy duty coolant system with static magnetic filter. -- 200 mm (8") Segmented holder with 6 segments. Mechanical T-groove chuck for stack grinding of knives with step blocks. Head travel guides are covered. Head travels on hardened and ground replaceable wear strips.
Equipment Location:WEST COAST
Bob Dykstra
800-374-5009 ext:378
|
|
MVM BM 850 --Grinder for straight knives up to a 33" in length ideal for chipper, shaving and planer knives. Automatic head travel with travel speed of 33 FPM. -- Automatic wheel down feed can be set for per pass and total downfeed. -- 2 HP Grinding motor with 16 mm spindle/shaft. -- Grinding chuck tiltable 0°to 90°and grinding head tilts +5°to -30°. -- Chuck clearence to wheel 1.2"and chuck width is 3.5". -- Heavy duty coolant system with static magnetic filter. -- Mechanical T-groove chuck for stack grinding of knives with step blocks. -- Head travels on hardened and ground replaceable wear strips and head travel guides are covered. -- Includes: (1) 125 mm vitrified cup wheel, (1) set of blade clamps and (1) set of step blocks for stacking up to (4) planer knives, (1/8" x 40° back clearence). -- Additional grinding wheel grit available.
Equipment Location:NORTHEAST
Bob Dykstra
800-374-5009 ext:378
|
|
MVM with 40” mechanical chuck -- Grinder for straight knives up to a 39" in length ideal for shaving, chipper and planer knives. -- Automatic head travel with travel speed of 33 FPM. -- Automatic wheel down feed can be set for per pass and total downfeed. -- 2 HP Grinding motor with 16 mm spindle/shaft. -- Grinding chuck tiltable 0°to 90° and grinding head tilts +5°to -30°. -- Chuck clearence to wheel 1.2" and chuck width is 3.9". -- Heavy duty coolant system with static magnetic filter. -- Mechanical T-groove chuck for stack grinding of knives with step blocks. -- Head travels on hardened and ground replaceable wear strips and head travel guides are covered. -- Includes: (1) 125 mm vitrified cup wheel for grinding and (1) set of Step blocks for stacking up to four planer knives at one grind. -- Warranty included on parts.ZX1000 Optional Accessories40” Magnetic Chuck option on ZX1000 MVM-ZX-0000900 $ 2,500 48” Magnetic Chuck option on ZX1230 MVM-ZX-0000901 $ 3,000(With tilling lever) T-Slot Device Mounts onto Magnetic Chuck $ 990 (Allows clamping + stack grinding knives up to 34”) Upgrade to 3.5HP & 6” Wheel (20mm bore) MVM-ZX-0000501 $ 880 Variable Carriage Speed (1 to 11 m/min) MVM-ZX-0001001 $ 1,600(Includes upgrade to metal control box with potentiometer) 400mm Super Hi-Power Mag Plate MVM-A-MP400 $ 1,750 (For grinding carbide inserts) Stops with sensors to limit the carriage travel MVM-ZX-000500 $ 660 (Requires external coolant tank and pump option) Step Blocks for stacking up to 4 planer knives MVM-AF2500-210XX $ 43 ea (Must specify knife thickness and back angle) Knife Extension resting blocks MVM-ZX-2579231600 $ 165 (Allow knives that are wider than the chuck to be referenced from the back) Rotary cutting edge references MVM-ZX-2579243000 $ 140 (Available on magnetic chuck only) External Coolant Tank and Pump XXX-ZX-000200 $ 1,200 (Standard machine uses the carriage bed as a coolant tank) 220v, single phase, Rotary Phase Converter (no loss in HP) RPC-3 $ 875 480v, 3ph, factory configuration $ 875 (or any voltage over 400
Equipment Location:NORTHEAST
Bob Dykstra
800-374-5009 ext:378
|
|
Grinder for straight knives up to a 53-1/2" (1,360 mm) in length for planer, veneer, paper, and chipper knives; stepless variable speed carriage with travel speed up to 40 FPM -- Manual-Automatic wheel down feed can be set per pass and total down-feed. -- 6.5 HP Grinding motor with 16 mm bore; grinding wheel at 2,800 RPM. -- Grinding chuck tiltable from 0° to 100°; chuck clearence to wheel is 4.3" (100 mm) and chuck width is 4.7" (120 mm). -- Heavy Duty coolant system with static magnetic filter. -- Equipped with: 200 mm (8") Segmented holder with (6) segments; mechanical T-groove chuck for stack grinding of knives with step blocks; covered head travel guides; head travel on hardened & ground replaceable wear strips. -- Includes: (1) 125 mm Vitrified cup wheel, -- Additional longer units available with grinding lengths of : 80" (2,000 mm), 120" (3,000 mm) and 178" (4,500 mm) - please contact us for pricing!
Equipment Location:NORTHEAST
Bob Dykstra
800-374-5009 ext:378
|
|
Newman G-132 Knife Sharpener
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
New Still on Pallet 48" Newman Knife Sharpener
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
Newman G-200 Knife Grinder
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
WEINIG R 960 Profile Knife Grinder;Specifications: 9-3/8" Max. arbor length, tool dia. 11-3/4" max. to 4" minimum. -- Grinding wheel: speed inverter controlled; speeds from 1,500 to 3,000 RPM by 1.5 HP motor. -- Hydro-clamping of grinding wheel to arbor. -- Tool carriage movement with precision linear table bearings, setting gauges for axial constant, axial (side) clearance angle 0° - 20° -- Equipped with: Onboard diamond wheel dressing, 8-7/8" max. 6" min. grinding wheel dia.; 13-gal. coolant tank with 1.2 HP pump.Includes: Choice of arbor dia.
Equipment Location:NORTHEAST
Bob Dykstra
800-374-5009 ext:378
|
|
WEINIG R912 Automatic grinder for straight knives, mill to pattern and fingerjoint heads, ground in the cutterhead.Specifications: -- Solid spindle carrier with precise guides for the concentricity below 0.0002". -- Grinding wheel dia. 5" with bore dia. 20 mm. Grinding spindle 2 HP, with spindle speed of 4,600 RPM. Clearence angle at radial knife back of 15 - 35°. -- Coolant pump flood works for cooling of the grinding wheel at the cutterhead with 2 HP pump. -- Grinding table ball threaded spindle drive for table and variable depth og grinding. -- Cutting circle 4" to 12" with working lenght of 13". Indexing plates for 1-36 knives. -- Operating panel with key pad and digital readouts. Electronic control for programming.
Equipment Location:MIDWEST
Bob Dykstra
800-374-5009 ext:378
|
|
WEINIG RONDAMAT R960 Powerlock Profile Tool Grinder -- Working dimensions 9-3/8" max. cutterhead length, tool dia. 3-15/16" to 11-13/16". --Specifications -- Motor: Inverter controled grinding wheel speed of 1,500 - 3,000 RPM with 1.5 HP motor. -- Productivity package: Machine light, back clearance angle motorized; grinding wheel advance motorized; setting of side clearance angle pneumatically. -- Tool carriage movement with precision linear table bearings, setting gauges for axial constant. tilting head assembly with radial (back) clearance angle 10° - 30° --Axial (side) clearance angle 0° - 20°. --Onboard diamond wheel dressing, 8-7/8" max. 6" min. grinding wheel diameter. 13-gal. coolant tank with 1.2 HP pump. --Equipped with & Features Includes: --All manuals and setup tools; (1) HSK arbor for conventional heads. --Grinder has the Locking bracket & Jack springs for transport --Reconditioned: The carriage bearings have been replaced, The spindles bearing has not been replaced, not necessary as per the Weinig Tech
Equipment Location:MIDWEST
Bob Dykstra
800-374-5009 ext:378
|
|
WEINIG RONDAMAT R960 Profile Knife Grinder. Working Dimensions: 9-29/64" maximum tool width; 3-15/16" Minimum to 11-13/16" Maximum cutting circle. -- Grinding Wheel: Diameter 5-29/32" min to 8-7/8" max. grinding wheel bore - 60 mm. Onboard diamond wheel dressing tool. -- Drive: Variable Frequency Controlled Drive giving a spindle speed - 1,500 to 3000 RPM; 1.5 HP Motor. -- Template carrier: Arbor 40 mm diameter. Utilizes a template-stylus-copy system, whereby the tool head table copying-grinding is effortless (precision linear floating table movement feels smooth as if there is zero gravity). Resistance template cross support with setting gauges for axial constant system; axial (side) clearance angle 0° - 20°. Holder for fixed and revolving tracing pins; for easy follow of template to grinding aggregate. -- Hydro-clamping; of grinding wheel to grinding arbor. -- Coolant: 13 gallon coolant tank capacity with 1.2 HP coolant pump. -- Note: If Grinder is purchased with CANTEK LMC 623 PLATINUM Moulder (see MF-013248), will include 200+ profiled knives, as pictured on last set of photos. If purchased separately knives available at extra cost.
Equipment Location:WESTERN CDN
Bob Dykstra
800-374-5009 ext:378
|
|
WEINIG "RONDAMAT " 925 Grinder, : -- 9 -1/2" Arbor length, 4" - 9" max. tool dia., 6" - 8-7/8" max. wheel dia., 1.5 HP motor, (4) grinding wheel speeds of 1,700 - 2,000 - 2,250 & 2,800 RPM. -- Clearance angle for back relief from 15ø - 35ø, axial from 0ø - 10ø; axial constant system, water bath table, 24-gallon coolant tank system with 0.09 HP pump, and 1-1/2" grinding arbor. -- , Electric system approx.. 1.5 kW
Equipment Location:MIDWEST
Bob Dykstra
800-374-5009 ext:378
|