Hogs and Wood Grinders For Sale

OVERBUILT - 10 Portable, ...Car CrusherIncludes Remote, FULLY LOADED. Specifications: -- (2) 10" Cylinders. -- Height: 10 ft. (raised); 24" ( lowered). -- Width: 7-1/2'. -- Length: 20-1/4". -- Lid movement: 8 ft. (Travel) -- Hydraulic cylinder: 10" x 4" Rod x 96" travel. -- Pressure: 2,400 PSI. -- Crushing force: 159 Tons

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

2003 Peterson HC5400 Grinder -7700 hours -New set of bananas, grates, and teeth -Has a wireless remote -Rotor recently balanced and serviced -New tires ands wheel bearings on axle -Comes with 25K worth of parts MACHINE RUNS AND WORKS BUT NEEDS A FEW MINOR REPAIRS -Has a hole in the metal plate that covers the rotor -Has a small leak in the fuel tank we currently use an auxiliary tank -Intermittent issue of conveyor not feeding. Believe it is a broken wire

Progress Industries 24" x 48" DFBD Swing Hammer with 200HP Motor.

Progress waste grinder, swinging hammer style, 125 hp electric drive, 1185 rpm's, unit needs to have hammers installed, good overall condition

RAPTOR - MINI TG, ...Tire Grinder / ShredderRAPTOR Tire Grinders are the most durable and easy to use Shredders built. Specfications: -- Feed opening: 33" x 36". -- Main motor: 200 HP. -- Size material down to: 3/4". -- Screen size: 3/4". -- Separates steel from rubber: 75% to 80%. -- Capacity: 2 Tons per hour (approx.).Equipped with: -- Full hardened knives. -- Electric control panel. -- Stand and infeed hopper.NOTE: New beearings and seals, a rebuilt gearbox, rebuilt gear reducer, and rebuilt electric motors. New frame and screen, too!

Excellent condition Less than 6 hrs on machine

REM - CC10, ...Used Can FlattenerThe REM Can Crusher is a complete separating, crushing, and blowing unit for aluminum cans.Specifications: -- Efficiently processes: 1,800 - 2,000 Lbs per hour. -- Load cans in the hopper and the conveyor carries the cans across the magnetic head pulley separating the steel from aluminum. -- The aluminum cans are crushed between a steel pressure plate and the rotating crusher drum with hardened steel bars; the cans then drop into a high-velocity air stream and are blown into a trailer or storage container. -- Features: 16" Wide belt; Crusher with: 10 HP 240/480-Volt, 3-phase; Blower with: 7.5 HP 240/480-Volt, 3-phase.

2005 Rotochopper Cp118 -1600 hours -120 hp engine -Lights and tires -One belt needs a patch(will be repaired)

Manufacturer’s Specifications Dimensions - Length: 46' 4? – 52' 6? - Width: 8' 6? - Height: 13' 6? - Weight: 42,000 – 47,000 lbs. Power Supply - 535 HP diesel engine - 200-gallon fuel capacity - PT Tech hydraulic clutch - Reversible radiator

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- Mellott Vibrating Conveyor -- Main drive motor: 75 HP -- Hammer width approx. 1-1/4" wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The" HZF Series" Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as: Rippings, edging, and trim blocks. Available in (4) standard sizes from 10" to 36" wide.&#9679 Each model features a built-in fan driven off of the main mill shaft, saving energy and valuable floor space while also significantly increasing production.

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

Schutte Hammer Mill 40-HZF with 100HP Electric Motor. No. 172 Attached Blower.

SCHUTTE-BUFFALO 15 Series, Model 15300 Wood Grinder;Complete with the following components and features: --Carbon Steel Construction. --Rotor approximate 44" diameter x 72" wide. --Approximately 3" wide Swinging Hammers, tip speed 20,700. --Top feed, bottom discharge. --Bottom screen approximate 5040 square inch area. --Clam shell housing. --500 HP, TEFC, 3/60/460 volt, 1785 RPM drive Motor with coupling and shaft guard. --Mounted on a heavy-duty steel Factory Frame. --NOTES: Largest model of the 15 Series. &#9679 Machine weight 16,000 Lbs.

Grinder. This machine is a Shutte grinder. With Webster vibratory infeed. Item #C625

Schutte horizontal hog, replaced shaft w/ blower & motor, heavy duty design (ref #162) Call Amy for more information (928) 723-9449