Woodworking Equipment For Sale
1745 Results Found
Call for Price
Capacities: 11” minimum length 98” maximum length 1” minimum width 32” maximum width 5/8” minimum thickness 3” maximum thickness Includes glue conveyor Model 300194-300198
$ 12,500
TAYLOR - 20-Section, ...Manual Clamp Carrier• 8' Width cap., approx. (6) clamps per section (108 clamps total).• 32" Max. clamp opening, (120) clamps with 2-1/2" jaw height.Complete with:Pneumatic air drive carrier rotation. -- Manual tightening. -- No panel flattener.
$ 19,900
TAYLOR 20-Section Clamp Carrier Specifications: -- 10.5' Width cap. -- 40" Max. clamp opening, 2-1/2" Jaw height. -- (6) clamps per sectionEquipped with: -- (120) Clamps total. -- Pneumatic tigthener -- Pneumatic panel flattenerComplete with: -- Air drive carrier rotation, -- I-Beam chain assembly.
$ 23,500
TAYLOR 40 Section Clamp Carrier.Specifications: -- 40-Section, 8-1/2' width capacity -- Average 4/5 clamps per section (175 clamps total), all with 32" max. clamp opening. -- Equipped with (175) clamps plus a pallet of spares that require repair, 32" clamps with 2-1/2" high jaws .Complete with: -- Heavy Duty Drive for rotation,& clamp tightening. -- Foot pedal control. -- Includes a glue applicator.
$ 21,500
TAYLOR - 40-Section, ...Clamp Carrier -- 10-1/2' Width cap. -- (240) Clamps total -- 32" Max. clamp opening with 3-1/2" high jaws. Complete with: -- Pneumatic panel flattener -- Pneumatic rotation -- 48" Plate spreader New in 2016Note: Tear down not included.
$ 14,200
TECNOMA - XT10.3 RS, ...Single Sided Edgebander.5/16" (5 mm) Max. edge cap., 1-1/2" (40 mm) max. banding height, 2-3/8" (60 mm) min. panel width, and 5-1/2" (140 mm) min. length. Equipped with: -- Automatic coil feed magazine with semiautomatic feed for strips, -- Teflon® coated glue pot (Heat up time 8 Min), -- Heavy-Duty 3 mm PVC capacity guillotine, 2-roll pressure unit w/1st roller power driven via clutch with pneumatic in & out positioning; 2nd roller idler roller. Workstations: -- Double motor front & rear end trim (0.41 HP - 12,000 RPM motor ea.), tilts 0° - 15°; end trimmer mounted on 45° THK guides. -- Top & Bottom flush trims (0.46 HP - 12,000 RPM motor ea.), equipped with "Quick Release" electric connectors for easy swap out of trim motors/tooling. -- Last Station: Top & Bottom buffing unit (0.2 HP - 2,750 RPM motor ea.), both adjustable. -- Single 26 FPM fixed feed speed, 0.8 HP feed drive. Complete with: -- Sound-proof enclosure, "Special" 70 mm wide chain pads, (2) rows of upper pressure wheels (60 mm dia. ea.) with "ball bearings" (vs. bushings) for long production life.
TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.
$ 112,000
MLS Number 11772789 2015 Thermwood FB53-510 CNC Router Very good working condition Low hours. Used for only 1 year. Excellent condition Moving gantry, fixed table, roller hold down CNC router Designed to machine low profile sheet materials(MDF, plywood, particleboard) Uses Microsoft Windows 10 Professional operating system
Call for Price
Thermwood C42 CNC Router (2) 5'x5' Tables It has 2 large routers, 4 smaller routers, and 2 aggregate heads in the turret Travainni Vacuum Pump Note from Seller: Includes two shaper heads that are not mounted into the turret and one pneumatic drill head that is not mounted into the turret. I also have one seat of Microvellum cabinetry program that I will transfer to you along with the purchase.
Call for Price
Call for Price
Call for Price
Tidland 470 Sander This system was used in a particle board plant that has been closed around 10 years.
Call for Price
- Automated push feed saw system for fast and accurate cutting of wood and plastic - Adjustable cutting envelope so you can set the envelope to the needed width of the material you are cutting, whether single piece or pack - Tigersaw 1000's Dynamic Optimization software give you the best yield by determining the optimal cutting order from your parts list - Value based optimizing allows the operator to value items in a cut list individually - Accuracy: +/- .012" - Push capacity: 90 lbs.(on flat tables) - Cutting envelope with 450 mm blade: 1" x 16" up to 5" x 6" - Cutting envelope with 500 blade: 1" x 16" up to 6" x 6" - Maximum clearance length for loading: 12' - Material feeds right to left - 24" wide x 18' long flat infeed table - 24" wide x 12' long roller outfeed table - Complete guarding of the saw blade area, safety interlocked guard door and saw blade door (neither can be opened while running) - Saw motor: 10 hp - Dust collection requirements: 600 cfm (4" dust port) - Air requirements: 85 psi (water and oil free air) - Electrical: 15 full load amps on 460 volt
Call for Price
Automated push feed saw system for fast and accurate cutting of wood and plastic Adjustable cutting envelope so you can set the envelope to the needed width of the material you are cutting, whether single piece or pack Tigersaw 1000's Dynamic Optimization software give you the best yield by determining the optimal cutting order from your parts list (Will cut the mark) Value based optimizing allows the operator to value items in a cut list individually Download parts files to Tigersaw 1000, comes with TigerLink 6 (Tigerstop's cut list downloading software) Accuracy: +/- .012" Push capacity: 90 lbs.(on flat tables) Cutting envelope with 450 mm blade: 1" x 16" up to 5" x 6" Cutting envelope with 500 blade: 1" x 16" up to 6" x 6" Maximum clearance length for loading: 12' Material feeds right to left 24" wide x 18' long flat infeed table 24" wide x 12' long roller outfeed table Complete guarding of the saw blade area, safety interlocked guard door and saw blade door (neither can be opened while running) Saw motor: 10 hp Dust collection requirements: 600 cfm (4" dust port) Air requirements: 85 psi (water and oil free air) Electrical: 15 full load amps on 460 volt INCLUDES: Tablet package: TigerTouch software loaded onto a Surface Pro tablet. Includes downloading software (DNLD), Dynamic optimization software (OPT), and TigerSET software (SET). Label printer
TIGER-TEC Rotary Vane Vacuum Pump:7 HP Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 82 CFM with max. 23.6"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less Vacuum Pump is virtually maintenance-free with: Built-in carbon vanes & built-in suction filters; vacuum regulating valve with canister filter, motor speed of 1,440 RPM, 220V, 3phase, weight 133kg (293lbs)dimensions: 39"L x 18"W x 24"H
Call for Price
Call for Price
Call for Price
Only 697 hours, taken from service (2) top heads - one orbit, one brush (1) 3HP main orbit motor (1) 3HP feed motor (1) 1HP brush motor (1) 1HP oscillation motor 460V Max. stock width 36" Max. thickness 6" 32-38" variable passline height 2,000 CFM @ 5,000 FPM exhaust air requirements
Call for Price
Call for Price
TIMESAVERS 4331-45-001 Wide belt sander (3) heads 51" width cap. 1st Head 9-1/2" Dia. rubber covered (60-65 Duro) 40HP motor 2nd Head 9-1/2"Dia. rubber covered (60-65 Duro) 30HP motor 3rd Head Combination head with 6" dia rubber covered contact roll and a 2-1/2" finishing platen. 30HP motor. 52" x 103" abrasive belts with dual "posi-trac" electronic-solid state tracking Controls mounted on belt loading side Conveyor feed belt replaced (2) years ago.