Woodworking Equipment For Sale

Gomad "DFDA-455" Sliding Table Single Spindle Shaper -- Specifications: 2-1/64" (55 mm) spindle currently, 7.5 HP belt drive motor, (4) speeds 4,000/6,000/8,000 & 10,000 RPM, 3-9/16" spindle travel, 3/4" up to 2-11/64" dia. interchangeable spindle, reversing spindle rotation; heavy duty 36" x 40" cast iron table, (3) pneumatic clamps, double end fence, 4.5" dia. dust chute. -- Complete with: 13" wide sliding table, (4) Hold down springs, mounting collars & bolts, miter gauge with stop rod, and foot brake, capable of doing arch molding work.NOTE: Don't go too much by the appearance. In running condition before disconnect in 2013, currently stored in the facility's basement.

GOODSPEED HF 412 AO Vertical Oscillating Chair Back Sander Specifications: Table size 30” x 30” x 34-1/4” H. Equipped with: 12" W x 25" L Horizontal abrasive belt, with 12” H x 4” Dia. Aluminum & Spiral rubber drums, 12” H x 3-1/2” Dia. Spiral rubber feed drum, with 2 HP Motor & Variable feed speed control. 60 W Feed & Oscillation motors.

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

GOODSPEED FH30 Semi-Automatic Copy Lathe. Specifications: --30" Cap. with a 3" max. dia., hopper feed for square or round stock, 15 HP main spindle motor for 2,250 - 3,200 - 3,825 & 4,625 RPM; reciprocating tail spindle. -- 2 HP Hydraulic feed on back knife; up to (900) pieces/Hr capacity. -- Complete with: Carriage slow down control system, pressure lubrication die system, 2-belt head spindle drive, and adjustable knife bar for cutting tapers. -- Includes: Pneumatic steady rest; Custom pressure reducer; used tooling and extras. -- Original manual included. -- Was used for making drumsticks.

INTOREX TXA-1200 Automatic Hydraulic Copy Lathe;Specifications: -- 1,200 mm (47-1/4") Max. turning length, 210 mm (8-1/4") max. turning diameter. -- Max. turning dia. with standard steady 90 mm (3.5"). -- (2) Hydraulic copiers. -- Max. size of square stock for turning with automatic feed 100 mm (3.9"). -- (3) Tool holder turrets. Hopper feed unit. -- (8) Head speeds in a range from 750 - 5,500 RPM. -- 6 HP or 7.5 HP Headstock spindle motor. -- 4 HP Hydraulic pump motor.

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally

Gorbel 500 Lbs Ceiling Hoist

GRASS - RAM, ...Drawer PressPneumatic Drawer Press used for pressing & inserting the GRASS SARGEN slide. -- Tabletop mount, foot pedal activation. -- NOTE: Machine is shown "as it is". Additional aluminum base frame was NOT shipped with this machine.

GRASS - ECOPRESS P: Boring Machine (Hinge) -- SpecificationsPneumatic tabletop unit mounted on welded frame base; hinge boring w/GRASS inserter block.(1) 3-Spindle boring head for hinges; 1 HP motor. -- Drill unit & insertion head and (2) spring loaded holddown cylinders operate pneumatically. Boring depth automatically sets to the material thickness being processed. -- Complete with: &#9679 450 x 730 mm Extruded aluminum framework table.&#9679 LH & RH material side stops. -- Actual Model: GRASS ECOPRESS P

Equipped with Glue Head

GRECON PJ 150/500 and PF 10-610 Finger Jointer and PressFinger jointer and Press systemSpecifications: -- Grecon Finger Joint System Including: Model PJ 150/500 Shaper -- Trim Saw 5 HP -- Shaper Head 30 HP -- Glue Application Head -- Timber Width 30 mm - 159 mm (1.2" - 6.25") -- Timber Thickness 12 mm - 80 mm (.5" - 3.15") -- Timber Length 250 mm - 1780 mm (9.84" - 70") -- Infeed Belt Conveyor 20" Wide X 34" LongAfter the Finger joint shaper: -- Manual Roll Conveyor with Rotation for Turning Workpieces 22" X 68" -- Outfeed Belt Conveyor 20" X 39" -- Driven Roll Conveyor 20" X 120" -- Powered Belt Conveyor Prior to Press 7" X 86"Model Press PJ 10/6100 Finger Joint Assembly Press: -- Maximum Pressing Length 240" -- Cut-Off Saw Motor 3HPNote: The machine will be reconditioned upon placement of order.

Greenfield Machinery Splitter Saw

6' x 14' capacity 4 HP motor 220 volt 3 phase stop system on base

Griggio C250 Rip Saw 250 mm Wide belt (10")

GRIGGIO G 1100 Wide belt Sander2-Head, 1,100 mm (43") width cap. -- 1st Head: Rubber covered steel contact roll, duro 85, 220 mm diameter . -- 2nd Head: Rubber covered contact roll duro 50 -- 25 HP motor to drive both head. -- 43" x 85" abrasive belts, electropneumatic abrasive belt tracking, -- Conveyor belt feed, two speed from control panel at 15 and 30 FPM, 0.4/0.7 HP feed drive, automatic conveyor belt tracking, -- 1/8" - 6-1/2" motorized thickness adjustment with LED readout & 0.75Hp gearmotor drive. --Automatic positioning of the working table, rubber covered spring loaded pressure rollers, double infeed and outfeed rubber covered rolls, infeed panel "over-thickness" sensor. --Two suction dust hoods dia. 6" (150mm),

GRIGGIO SC-1500 Table Saw Specifications: -- 60" Cut cap.; 5 HP main motor & scoring motor with 3/4" dia. arbor and 9,000 RPM blade speed; external scoring blade adjustment. -- Features: -- 0° - 45° Tilting 1" dia. main saw arbor, 16" max. blade size, 5.1" max. depth of cut, single blade speed. -- Rip-cut fence assembly adjustable to 60" max.NOTE: Dimensions and weight are approximate.

GRIZZLY H2934 2-HEAD WIDE BELT SANDER2-Head Wide Belt Sander, 36-1/2" width cap. -- Head configuration: - 1st Head: Rubber covered contact drum; 2nd Head: Combination head with rubber covered contact drum and adjustable platen; Abrasive belt size 37" x 60". -- 0" to 6" Thickness cap., LED digital depth encoder; 14" min. board length and 12" infeed conveyor. -- 1st Abrasive belt surface speed of 3,543 SFPM; 2nd abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP - 50/25 Amp Sanding motor; 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor. -- Complete with: Rubber covered holddown rolls, adjustable felt platen, Amp/load meter, and disc brake for emergency stop.

GRIZZLY - G1026, ...Single Speed Shaper w/Feeder & Mobile Base3 HP - 3,450 RPM Motor; 1/2", 3/4" & 1" dia. interchangeable spindles; 2-1/2" spindle cap. under the nut and with 3" spindle travel. -- (2) Spindle speeds of 7,000 or 10,000 RPM; reversing spindle switch. -- Features: 28-1/4" x 21-3/4" table; 34" table height.Complete with: Magnetic spindle brake, adjustable fence & 3" dia. dust extraction outlet.3-Roll 4-Speed Power Feeder & Mobile Base!

15" Width cap. with 1/4" - 8" thickness opening, 1/16" max. depth of cut; 3 HP single-phase motor belt drives 3-knife, 3-15/64" dia. cutter-head at 5,000 RPM; head with high-speed steel knives, max. thickness 8", min. 3/16"; dual feed speed of either 16 or 30 FPM; 16" x 42" cast iron table, table extensions on infeed/outfeed. Complete with: Magnetic controls, 2" dia. metal infeed & outfeed rollers, open fabricated steel base, and large hand wheel for cutter-head assembly adjustment.