Edgebanders For Sale

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL/HIGH PRODUCTION) (aka "TAPE ROCKET"): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.012. - 0.125"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). Minimum Work piece length 610 mm(24").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt GA 65 / QA 65: QA 65 - EVA Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit PK 25:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Fine Trimming Unit PF20:(2) 0.54 HP ( 0.4 kW) - 12,000 RPM, fine trimming unit for edge overhangs at the work-piece upper & lower edge.Operator Interface: -- Power Touch Control Multi-Touch Screen Controller on separate console with 21.5" Full HD flat screen display, keyboard and mouse. Functions in Windows environment, includes fault diagnostic, OS9 real-time operating system."WoodScout", included graphic diagnostic tool designed to increase throughput and decrease down time. Graphical PLC diagnosis display of the error location in the machineCustomer-specific data base system that allows the operator to enter the reason for the error as well as the corrective measures to assist with future tro

Manufacturer’s Specifications - For banding edges of up to 3 mm and workpieces of up to 40 mm (60 mm - 1130 FC | 1130 AT) - Glue applied directly onto the workpiece to ensure constant application (i.a. for processing of PUR-glue). - Two-motor end-trimming unit for optimum cutting results - Contour trimming unit for rounding corners - Freely configurable post-processing for a high level of flexibility - Zero joints - airTec unit for a perfect zero joint finish - 400/220 V

HOMAG EDGETEQ S-200 B EDGEBANDER (COMPACT): -- Specifications:0.4 - 3 mm (0.016 - 0.125") edge coil/strips thickness; 8 - 40 mm (0,312 - 1.6") panel thickness; 140 mm (5.5") min. panel length and 70 mm (2.75") min. panel width.Equipped with: -- Automatic Edge Magazine, for strip & coil stock, up to 3 mm PVC. -- "Heavy Duty" guillotine. -- EVA "Quick-Change" glue pot and roller application unit. 12-15 min. heat up time, re-heat - 3min. -- Pressure Section, 1st. roller driven plus (2) idle rollers, timed pneumatic pressure controlled. -- Feed Speed, 8 MPM. (26 FPM). Operator Interface: -- HOMAG "easyTouch" Operator Interface with 7" graphic color touch display & soft keypad. Intuitive, user-oriented navigation.20 storable programs guarantee flexibility when processing a wide variety of edge materials and changing customer requirements.Clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain textWorkstations: -- End Trimming: - (2) Motor @ 0.18 kW (.24 HP) 12,000 RPM on linear guides. -- Fine Trimming Unit: - Top/bottom (2) motors, 0.27 kW (.36 HP) 12,000 RPM, with (3) working positioning: (1) flush trimming, (2) trimming with overhang, (3) radius/bevel trimming. -- Open Space: For the addition of a "Quick Change" Profile Scrapping Unit. -- Buffing Unit: - Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. Complete with:Manual adjusted top hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling and Original Factory machine documentation. -- Actual Model is HOMAG EDGETEQ S-200 B.

HOMAG EDGETEQ S-300 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + AirTec EVA/PUR Gluing Technology:Specifications:0.4 - 8 mm (0.016 - 5/16") edge; 8 - 60 mm (5/16 - 2-3/8") panel thickness; 160 mm (6-3/8") min. panel length and 70 mm (2-3/4") min. panel width.Equipped with: Pre-Milling Station, (2) motors @ 2.25 kW (3.0 HP), 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges.Equipped with diamond cutter heads. -- In-feed Fence, with servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine, for strip & coil stock, strips 0.4 mm - 8 mm (0.016 - 5/16"), coils up to 3 mm PVC and "HD" guillotine. -- "AirTec" EVA/PUR gluing Technology with "Quick Change" Glue Tank for maintenance & glue color change. -- Pressure Section, 1st. roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed, variable 8 - 14 MPM. (26 - 46 FPM), 11 MPM (36 FPM) when using contour trimming. -- HOMAG "Power Touch Control, Memory: 256 MB Ram, 1 GB Flash Card Drive.Operator control panel w/22" color HD wide screen, soft keypad & internal modem for remote diagnostic link.Workstations: End Trimming: - (2) Motor @ 0.35 kW (1/2 HP) 12,000 RPM, automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: - Top/bottom (2) motors, 0.55 kW (3/4 HP) 12,000 RPM, auto tilt positioning 0° - 25°, with combination flush/radius/chamfer cutter-heads.Horizontal and vertical tracing wheels, equipped with brushless multi-axis Servo motors for positioning of work-unit & horizontal copy wheels for quick changeover. Includes (3) positioning options, profile 1, profile 2, and flush trimming, and nested top copy system. -- Corner Rounding Unit: (1) Motor 0.35 kW (1/2 HP) 12,000 RPM, with manual adjustment for 1-mil, 2-mil & 3-mil thickness.For leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multi-Profile (PVC): Top/bottom with (2) profiles. 1 mm and 2 mm or 3 mm instead of 2 mm, servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Scraping Glue Unit: - Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: - Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. Complete with:Motorized, programmable hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling and Original Factory machine documentation. -- Actual Model is HOMAG EDGETEQ S-300 AirTec, OPTIMAT KDF 440C.

HOMAG EDGETEQ S-500 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.3 - 20 mm (0.011 - 7/8") Edge material thickness; 8 - 60 mm (0.3' - 2.375") panel thickness; 160 mm (6.375") min. panel length and 70 mm (2.75") min. panel width.High flexibility is achieved as all edge materials can be processed: 0.3 mm Melamine, up to 3 mm ABS, PP, PVC and wood as coil material.Solid wood strips and veneer strips up to 12 mm are fed in individually and up to 20 mm from the package. Even veneer strips of up to 1 mm can be fed from the package.For perfect high-gloss parts, important components such as the motor-driven top pressure and the automatic adjustment of the glue joint scrapers are used.Special tracing elements are ideal for processing of acute angled or obtuse angled parts or parts with hinge holes and transversal grooves.Variable Production Feed Speeds from 16 - 30 MPM (52 - 98 FPM). -- Equipped with: Separating agent spraying unit. -- Pre-milling Station: (2) Motors @ 2.25 kW (3.0 HP), 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Infeed fence with Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine for strip & coil stock, strips 0.4 mm - 12 mm (0.015 - 0.47"), coils up to 3 mm PVC with "HD" guillotine. -- "Quick Change" Glue Tank for maintenance, glue type & color change. -- Pressure Section: 1st. Roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- HOMAG "PowerTouch control, memory: 256 MB RAM, 1 GB Flash Card Drive. -- Workstations: End Trimming: (2) Motors @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Multistage MS40 Flush/Bevel-Fine/Radius Trimming Unit:Top/bottom: (2) Motors, 0.55 kW (3/4 HP) - 12,000 RPM, auto-tilt positioning 0° - 25°; with combination flush/radius/chamfer cutterheads. -- Multifunctional trimming unit MF60 Servo trim - Horizontal and vertical tracing wheels, equipped with brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes (3) positioning options: Profile 1, profile 2, and flush trimming; nested top copy system. -- Corner Rounding Unit: (1) 0.35 kW (1/2 HP) - 12,000 RPM Motor for leading & trailing edges, vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, multi-profile (PVC): Top/bottom with (2) profiles (1 mm and 2 mm or 3 mm instead of 2 mm), Servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Flat Glue Joint Scraping Unit: Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: Top & bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. -- Operator Control: HOMAG powerTouch2 control with clearer structure, 3

HOMAG EDGETEQ S-500 EDGEBANDER (W/PRE-MILL) (aka "TAPE ROCKET" 2.2 LH): -- Specifications:0.3 - 3 mm (0.012 - 0.125") Edge material thickness; 8 - 60 mm (0.3' - 2.375") panel thickness; 160 mm (6.375") min. panel length and 60 mm (2.36") min. panel width.High flexibility is achieved as all edge materials can be processed: 0.3 mm Melamine, up to 3 mm ABS, PP, PVC & wood as coil material.For perfect high-gloss parts, important components such as the motor-driven top pressure and the automatic adjustment of the glue joint scrapers are used.Special tracing elements are ideal for processing of acute angled or obtuse angled parts or parts with hinge holes and transversal grooves.Selectable Production Feed Speeds from 16 - 30 MPM (52 - 98 FPM). Minimum workpiece gap 500 mm @ 25 MPM. -- Equipped with: LPZ/II Release Agent spraying unit. -- Pre-milling Station: (2) Motors @ 3 kW (4.0 HP), 9.000 RPM; LH & RH rotation w/electro-pneumatic jump control for chip-free and clean panel edges. Equipped with diamond-insert cutter heads. -- Infeed fence with Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic 2-Coil Magazine for coil stock 0.3 mm - 3 mm (0.011 - 0.12"), "HD" guillotine. -- QA-65 P Gluing Unit with Quick Melt Pre-Melter & "Quick Change" Glue Tank for maintenance, glue type & color change. -- Pressure Section: 1st. Roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- HOMAG "PowerTouch control, memory: 256 MB RAM, 1 GB Flash Card Drive. -- Workstations: End Trimming unit PK 25 - (2) Motors @ 0.8 kW (1HP) - 12,000 RPM; Programmable electro-pneumatic reset from chamfer to straight trimming • Programmable electro-pneumatic adjustment of motors to positions: • Flush/Bevel trimming • Overhanging for Post Processing. -- PF 20 Fine Trimming Unit - (2) Motors @ 0.4 kW (0.5 HP) - 12,000 RPM. • Height adjustment synchronized with top pressure beam • Swiveling range: 0° – 25° is manually adjustable between different workpiece thicknesses. -- PN10 Profile Scraping Unit with • tracing from top, bottom, and side • pneumatically-controlled blow off nozzles • height adjustment synchronized with top pressure beam • suction collection box for edgebanding material scrapings • electro-pneumatic positioning in/out of the processing area, with (2) quick-change scraper heads. -- FA 20 Basic Glue Joint Scraping Unit to remove glue residue unit from the top and bottom, which eliminates additional hand scraping and cleaning. • Height adjustment is synchronized with the top pressure beam • Electro-pneumatic positioning in and out of the processing area. -- FA 06 Edge Buffing Unit to cleans and restores luster to plastic edges on the top & bottom. -- LP163/93 Cleaning Agent Spraying Unit before buffing helps clean the edges. • 2 spray nozzles for application • A 2-liter bottle of release agent is prov

HOMAG OPTIMAT KL-75 / A20 EDGEBANDER 0.4 - 20 mm (3/4") Thickness edgebanding cap., 70 mm min. panel thickness.Equipped with: Automatic edge feed magazine for coil, HPL & strip stock; "Hot Melt" glue system with QA34 Quickmelt unit, with reversible glue roll applicator; pneumatically controlled pressure roll section with 7 pressure rollers. -- Workstations: Double motor front & rear end trim, straight & chamfer trimming (0.5 HP - 10,400 RPM ea. motor). -- Top & Bottom rough trims (2 HP - 11,500 RPM ea. motor). -- Top & Bottom fine trims, tiltable 0° - 30° (0.5 HP - 10,980 RPM ea. motor); open space for workstation. -- Adjustable top and bottom glue scraper. -- Electronic Height adjustment for Top pressure beam with double V-belts, 80 mm wide Heavy Duty feed chain w/rubber pads. -- Feed speed variable up to 35 MPM. -- Complete with: SIKO Digital adjustments on T & B Flush and Fine Trim. -- Homatic NC21 Controller, Fixed position Outrigger panel support, insulated sound cabins w/interior and overhead lighting for all trim workstations. -- Includes Owners Manual and the Electrical Schematics.NOTE: Suggested replacement parts needed, as noted by our technician - all the track pads, the hold-down belt, the pressure roller, and likely a glue pot rebuild. Estimated cost for these parts, not including labor is $5600. The replacement of these parts is NOT included in the machine price.

HOMAG KL 78/A20/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: 0.4 - 20 mm ( 0.02" - 0.78") Edge thickness cap., min. panel width 55 mm (2.18") for panel thickness 12 - 22 mm (0.5" - 0.875") and under; 100 mm (3.9") for panel thickness over 22 - 60 mm (0.875" - 2.3"); for up to 3 mm Coil stock, HPL, and strip stock up to 20 mm (0.75").Feed & Infeed Section of Machine: -- Top pressure beam with: Double-wide compound V-belts; 80 mm wide feed track chain plates, vulcanized rubber insert pads, and Auto-Lube; variable feed speed from 18 - 24 MPM (59 - 79 FPM); 950 mm height/working level infeed. -- Pre-Milling Station with: (2) 3 kW - 150 Hz, 9,000 RPM Motors, panel blow-off device; 2-position infeed fence (on/off), SIKO digital manual fence control. -- Panel Pre-Heater with: Quartz lamp for heating substrate edge before glue application. -- Edge Feeding device equipped with: Automatic coil magazine for quick coil changeover; strip feeder for up to 20 mm (3/4") solid wood banding. -- "Quick Melt" Glue System with: Reversible glue roller applicator; pressure roll section with (1) large dia. driven and (6) idle rollers; manual adjustment of pressure zone through SIKO digital counters for different edge thicknesses.Edgebanding Workstations: -- Double motor front & rear end trim, straight & chamfer trimming (0.8 HP - 12,000 RPM ea. motor). -- Top & Bottom flush trim (2 HP - 12,000 RPM ea. motor). -- Corner rounding unit: Equipped with (4) motors, 2 HP - 12,000 RPM each motor. -- Universal Milling/Grooving Unit tiltable 90°. -- Edge Scrape Super-Finishing unit for thick PVC/ABS with chip collection box. -- Top & Bottom Flat Glue Scraper to remove potential glue squeeze-out. -- Top & Bottom oscillating buffing unit (two 0.33 HP - 1,650 RPM motors). -- "HOMATIC NC 21" controller features with Keypad & LCD display, stores working programs and controls functions of workstations, allows fault diagnostic and more, etc. -- Complete with: PLC controlled, motorized beam height adjustment; servo adjustments on Top & Bottom flush trim, and servo controlled Scraper Stations. -- Electronic DC brakes on all trim motors, sound cabins for all trim workstations, and adjustable outboard panel support. -- Actual Model is HOMAG KL 78/A20/S2.

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG KAL 310/3/A3 Edgebander ... High Production - aka Tape Rocket -- Working Capacity:0.4 - 3 mm Edge thickness cap., min. panel width 55 mm; max. panel thickness 55 mm; Feed speed variable up to 18 to 32 MPM (59' to 104' FPM).Equipped with: -- Vertical Coil Tape Magazine; (2) positions, SIKO digital adjustments. -- Glue System "A34", hot melt with reversible glue roller applicator; -- Side Pressure Section with (1) large dia. driven & (2) idle rollers; manual adjustment of pressure zone through SIKO digital counters for different edge thicknesses. -- HOMATIC "PC 21" Controller features, function in Windows environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem.Workstations: -- End Trimming (2 x 0.25 HP - 200 Hz, 12,000 RPM each) to cut excess edge on the front & back of the panel. -- Trimming Station, top & bottom 2 x 1.0 kW (1.35 HP - 12,000 RPM). --÷ Buffing Unit, top & bottom 2 x 0.25 kW - 2,850 RPM each motor.Complete with & Features: -- Electronic DC Brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- Feed Track Pads 80 mm wide; manually adjusted -- V-groove belt on top pressure beam and Sound/Safety enclosure over workstations.

HOMAG KAL 310/4/A3/S2 EDGEBANDER (W/PRE-MILLING): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

--at Auction, Seller Loading, Good Condition-- HOMAG KAL 310/4/A3/S2 Edgebander, with Pre-Mill Specifications: - Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed Equipped with: - Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. - Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; - Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. - Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges - HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. Workstations: - End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. - Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. - Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters - Profile Edge Scraping Unit: with electro-pneumatic adjustment - Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM Complete with & Features: - Electronic DC brakes on all trim motors; sound cabin for all workstations. - Adjustable outboard panel support with swing out arms for up to 800 mm. - 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. Note: This machine has a new display and a new back up one as well!

HOMAG KAR 310/6/A3/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Special "RIGHT-HAND" Feed HOMAG. -- Specifications:Working Capacity, 0.3 - 3 mm Edge thickness cap., min. panel width 55 mm; max. panel thickness 60 mm; feed speed variable from 18 - 25 MPM (59 - 82 FPM).Equipped with: -- Pre-Milling Unit: (2) Motors, 3 kW - 9,000 RPM each motor; pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator infeed fence. -- Hot Melt Glue System: Quick Melt Unit with reversible glue roller applicator. -- Edge Magazine: Automatic 1-Coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers. (1) Large dia. driven & (2) idle rollers; "NC" adjustment of pressure zone through the control for different edge thicknesses. -- Spraying Device: Top and Bottom spray nozzles for applying separating agent, for easier cleaning of any residual glue on panel.Workstations: -- End Trimming Unit: (2) Motors, 0.5 kW (0.7 HP) - 12,000 RPM each motor; cuts excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit - Top & bottom Trim Station, 1.5 kW (2.0 HP - 12,000 RPM) Motor; +/- 1° angle adjustment, manual positioning with digital counters. -- Profile Trimming/Corner Rounding Unit: (2) Multifunction motors to process the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear edge; (2) 0.55 kW (HP 0.73) each motor. -- Open Station: Open space of 23.6" (600 mm), for future installation of a working unit. -- Profile Edge Scraping Unit: Electro-pneumatic adjustment. -- Finish Process Unit with Glue Scraper + Buffing Unit: Flat top & bottom panel surface glue scraper & buffing, removes any potential squeezed-out glue residue.Operator & Machine Control: HOMAG "Power Control PC 22 + Windows "XP" operating System. Controller on separate console with 19" flat screen display, keyboard, and mouse. Includes fault diagnostic, OS9 real -time operating system. Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam, and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAR 310/6/A3/S2, Special "RIGHT-HAND" Feed Configuration HOMAG.

IMA NOVIMAT CONCEPT/I/G80/440/L20 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Edgebanding capacity, 0.4 - 3 mm; (0.016 - 0.118") and solid wood strips up to 20 mm (0.787) thickness; Panel thickness min/max 10 - 60 mm (0.394 - 2.362") (min 10 - 40 mm (1.575") with contour trimming, max. 60 mm without contour trimming); Min Panel width 65 mm (2.559"), min panel length 150 mm (5.906"), edge length min. 250 mm (9.843") with material up to 3 mm; Feed speed 8 - 40 MPM (26.4 - 132 FPM).Equipped With: -- Indeed fence. Panel pre-heater (2) x 1,500 Watts. -- Pre-Milling Unit 08.0555 with KW 4.5 x 2 (HP 6 x 2) 9,000 RPM, vertical joining spindles, N.C. controlled, both w/jump movement and reversible rotation, SIKO digital readouts, particle & debris air jet blower. -- Spraying Unit, anti-sticking solvent (release agent), top bottom application. Between Pre-Mill and glue station. -- Coil magazine with HD guillotine, automatic coil changeover. Lot of vertical coil magazines. -- Glue System: EVA Glue (Hot Melt) Glue pot and Pre-melter with large capacity 30 Kg floor mounted hopper. -- Side Pressure Section: (1) driven and (5) idle rollers. N.C. controlled w/individual pneumatic pressure control for each rollWorkstations: -- End Trimming Unit: 08.42/30/B High speed, double motor 2 x KW 0.66 (HP 0.88) - 12,000 RPM. Horizontal model suspended from the hold-down beam, automatic chamfer adjustment 0° - 25° for speeds up to 32 MPM (105 FPM). -- Rough Trim: Unit 08.055. 1 KW (1.34 HP) - 12,000 RPM motors), Overlapped motor mounts, -- Multi-Function Unit (MFA) Radius and Chamfer milling Corner Rounding station Unit 08.348.. Controlled by N.C. with double automatic copying devices with 4+4 positions (total 8) for multiple edge thickness control, 0.66 kW (0.88 HP)- 12,000 RPM motors. -- Profile Edge Scraping Unit 08.519: Top & bottom, multi profile (4) positions N.C. controlled scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing wheels, digital readouts for adjustments, chip extraction system for scraping unit. -- Glue Scraping Unit 08521: Flat, top & bottom self-tracing glue scraper, N.C. controlled. -- Spray Nozzle top/bottom fir cleaning agent. -- Buffing Unit 08.617-2.: Top/bottom KW 0.18 (HP 0.25 x 2) - 1400 RPM ea. for buffing & polishing.Operator Interface: -- ICOS compact with the following features: Display color screen, floppy disk reader, keyboard, adjustable hanging control board. -- Sound-proof enclosure cabinet over all the working units with interior lights.

IMA - HKA EXPERT CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. Designed for straight or curved (contour) edgebanding:0.5 - 3 mm Edgebanding thickness; 16 - 45 mm (0.63" - 1.77") panel & banding height; 23 - 45 mm (0.9" - 1.77") min. strip width; 100 mm (3.9") min. panel width; 250 mm (9.8") min. strip length. -- Equipped with: Versatile glue head that can be fixed to 1-side of the table to allow the operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine, via foot-pedal control. -- Work Table:32" (800 mm) Dia. coil dispensing table, large 813 x 914 mm (32" x 36") High-Flow Phenolic worktable surface;Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head (hot melt) glue pot" with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA 500L Edgebander Will need a new touch screen control and calibration.

IMA ADVANTAGE 500 L EDGEBANDER (w/PREMILL & CORNER ROUNDING): -- Specifications:Edgebanding capacity: Coiled material: 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped with:Pre-milling Unit: 4 kW x 2 (5.3 HP x 2) - 9,000 RPM Vertical joining spindles; SIKO digital readouts, and particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit: Dual motor, (2) 0.66 kW (0.88 HP) motors; suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit: Top & Bottom flush trimming, W 1.0 kW x 2 (1.34 HP x 2) - 12,000 RPM Ea. motor; against the feed (up milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit: Multiuse; Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W - 12,000 RPM. -- Profile Scraper Unit: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all holddown beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is I M A ADVANTAGE 500 L

--Auction Listing, Seller Loading, Cleaned and Checked-- IMA ADVANTAGE 500 L Production Edgebander, with Pre-Mill & Corner Rounding Basic Specifications: -Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362"). Equipped With: - Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. - Glue System - EVA (Hot Melt) with: "Quick-Lock" System. - Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations: - End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. - Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. - Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. - Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. - Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. - Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. - Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge. - Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations. Complete with: - Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). - Motorized central height adjustment of top pressure beam with double V-belt hold-down. - Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. - Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station.

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L