Homag Edgebanders For Sale

As Taken From Service: Includes return conveyor

Homag KAL 310 NOT INCLUDING THE RETURN Year of MFG 2006 Control voltage 24 V total connected load 50A recommended fuse 28kW nominal current pprox.. 39A Dust extraction air velocity (min.) 28 m/sec (91.84 ft/sec) air volume 4090 m3/hr (2407 cfm) static pressure 250 mm/ws (9.84”/ws) CompressedAir connection size ¾” pressure required 7 bar (100 psi) consumption / volume 705 sl/min (24.89 cfm) Foundation requirements according to layout drawing # 5-236-01-0360 Electrical equipment installed according to UL regulations. Voltage supplied must not fluctuate in excess of+/- 5% of its stated value. Voltage must be balanced phase-to-phase and phase-to-ground. Note: The stated values are only applicable to the machine as specified. Adding or deleting optional equipment may change service connection requirements. In case ofvariations in technical specifications and capacities between the base machine and working units, the specifications and capacities given for the working units are to be considered correct. Conditions offloor at installation site must adhere to foundation plan. Adjustable lnfeed Fence Homag Unit #0005 • with digital mechanical counter Pre-Milling Unit Homag Unit #3481 HOMAG KAL 525 • with two (2) motors 3 kW, 150 cycle, 9000 rpm • for max. tool diameter of 125 mm (4-15/16") • equipped with trimming column • two (2) horizontal and cross slides with spindle adjustment • electro-pneumatic horizontal jump movement of first motor • two (2) dust extraction hoods • air jet for panel cleaning • with two (2) DIA jointing heads 125 x 35 x 30 mm(4-15/16" x 1-3/8" x 1-1/8"), DKN, z = 2 x 3 • max. workpiece thickness 30 mm (1-1/8") • electronic frequency inverter for control of motor speed and braking Noise Protection Stepped Homag Unit #0424 • for pre-trimming unit • allows for inlay of long strips • centralized dust extraction port Panel Pre-Heater Homag Unit #2325 • quartz lamp for heating substrate edge before glue application • for improved edge quality and optimum bonding QA 34 Quick Melt Gluing Unit Homag Unit #2123 • specially designed by Ho mag - the original innovator of the quick melt syste • lower reservoir unit is designed with only seven (7) wearing parts, which allows for ease of adjustment and reduces maintenance costs • ideally suited for quick heat-up time and color changes • one bolt secures lower unit to drive mechanism • special coupling eliminates alignment of universal drive joint • digitally displayed thermostat for both upper and lower unit, along with heated glue roller allow for excellent control of temperature for optimum bonding results • individual adjustment for front and rear glue gates • upper reservoir for glue granules • glue roller diameter 34 mm (1-11/32") • lower melting unit equipped with automatic control of glue level Glue Roller Drive Homag Unit #2141 • eliminates glue charring on glue roller • lengthens pot life of glue during idle running time o

Manufacturer’s Specifications - For banding edges of up to 3 mm and workpieces of up to 40 mm (60 mm - 1130 FC | 1130 AT) - Glue applied directly onto the workpiece to ensure constant application (i.a. for processing of PUR-glue). - Two-motor end-trimming unit for optimum cutting results - Contour trimming unit for rounding corners - Freely configurable post-processing for a high level of flexibility - Zero joints - airTec unit for a perfect zero joint finish

HOMAG KAR 310/6/A3/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Special "RIGHT-HAND" Feed HOMAG. -- Specifications:Working Capacity, 0.3 - 3 mm Edge thickness cap., min. panel width 55 mm; max. panel thickness 60 mm; feed speed variable from 18 - 25 MPM (59 - 82 FPM).Equipped with: -- Pre-Milling Unit: (2) Motors, 3 kW - 9,000 RPM each motor; pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator infeed fence. -- Hot Melt Glue System: Quick Melt Unit with reversible glue roller applicator. -- Edge Magazine: Automatic 1-Coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers. (1) Large dia. driven & (2) idle rollers; "NC" adjustment of pressure zone through the control for different edge thicknesses. -- Spraying Device: Top and Bottom spray nozzles for applying separating agent, for easier cleaning of any residual glue on panel.Workstations: -- End Trimming Unit: (2) Motors, 0.5 kW (0.7 HP) - 12,000 RPM each motor; cuts excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit - Top & bottom Trim Station, 1.5 kW (2.0 HP - 12,000 RPM) Motor; +/- 1° angle adjustment, manual positioning with digital counters. -- Profile Trimming/Corner Rounding Unit: (2) Multifunction motors to process the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear edge; (2) 0.55 kW (HP 0.73) each motor. -- Open Station: Open space of 23.6" (600 mm), for future installation of a working unit. -- Profile Edge Scraping Unit: Electro-pneumatic adjustment. -- Finish Process Unit with Glue Scraper + Buffing Unit: Flat top & bottom panel surface glue scraper & buffing, removes any potential squeezed-out glue residue.Operator & Machine Control: HOMAG "Power Control PC 22 + Windows "XP" operating System. Controller on separate console with 19" flat screen display, keyboard, and mouse. Includes fault diagnostic, OS9 real -time operating system. Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam, and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAR 310/6/A3/S2, Special "RIGHT-HAND" Feed Configuration HOMAG.

HOMAG AMBITION 2262 (KAL 210) PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"),Panel stock min/max thickness 12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence:Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station:Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment.Electro-pneumatic horizontal jump movement of the first motor; includes electronic frequency inverter for control of motor speed and braking.(2) Dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-HeaterPre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material, strips, and solid wood bands. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgeband. -- Pre-Melting System: Overhead Pre-Melting Unit -- Gluing System: (EVA - Hot Melt)QA 34 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allow for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/h (26 LBS/h) -- Pressure Section:Manual Adjustment with digital counter, (1) large 160 mm dia. driven & (6) 70 mm dia idle rollers, pneumatic pressure control depending on edgbanding material used.WORKSTATIONS: -- End Trimming Unit:0.8 kW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30 deg. to straight cut. -- Rough/Pre-Trimming Unit:Top & bottom, 0.55 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. Manually adjusted with digital counters. -- Multi-Function Profile/Bevel/Corner Rounding Unit:Multi function 0.4 kW (0.54 HP) x 2)- 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge; Servo controlled.Max. feed speed 20 MPM (65.6 FPM) when corner rounding. -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit:Top & bottom edge buffing/pol

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG KAL 310/3/A3 Edgebander ... High Production - aka Tape Rocket -- Working Capacity:0.4 - 3 mm Edge thickness cap., min. panel width 55 mm; max. panel thickness 55 mm; Feed speed variable up to 18 to 32 MPM (59' to 104' FPM).Equipped with: -- Vertical Coil Tape Magazine; (2) positions, SIKO digital adjustments. -- Glue System "A34", hot melt with reversible glue roller applicator; -- Side Pressure Section with (1) large dia. driven & (2) idle rollers; manual adjustment of pressure zone through SIKO digital counters for different edge thicknesses. -- HOMATIC "PC 21" Controller features, function in Windows environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem.Workstations: -- End Trimming (2 x 0.25 HP - 200 Hz, 12,000 RPM each) to cut excess edge on the front & back of the panel. -- Trimming Station, top & bottom 2 x 1.0 kW (1.35 HP - 12,000 RPM). --÷ Buffing Unit, top & bottom 2 x 0.25 kW - 2,850 RPM each motor.Complete with & Features: -- Electronic DC Brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- Feed Track Pads 80 mm wide; manually adjusted -- V-groove belt on top pressure beam and Sound/Safety enclosure over workstations.

HOMAG OPTIMAT KL-75 / A20 EDGEBANDER 0.4 - 20 mm (3/4") Thickness edgebanding cap., 70 mm min. panel thickness.Equipped with: Automatic edge feed magazine for coil, HPL & strip stock; "Hot Melt" glue system with QA34 Quickmelt unit, with reversible glue roll applicator; pneumatically controlled pressure roll section with 7 pressure rollers. -- Workstations: Double motor front & rear end trim, straight & chamfer trimming (0.5 HP - 10,400 RPM ea. motor). -- Top & Bottom rough trims (2 HP - 11,500 RPM ea. motor). -- Top & Bottom fine trims, tiltable 0° - 30° (0.5 HP - 10,980 RPM ea. motor); open space for workstation. -- Adjustable top and bottom glue scraper. -- Electronic Height adjustment for Top pressure beam with double V-belts, 80 mm wide Heavy Duty feed chain w/rubber pads. -- Feed speed variable up to 35 MPM. -- Complete with: SIKO Digital adjustments on T & B Flush and Fine Trim. -- Homatic NC21 Controller, Fixed position Outrigger panel support, insulated sound cabins w/interior and overhead lighting for all trim workstations. -- Includes Owners Manual and the Electrical Schematics.NOTE: Suggested replacement parts needed, as noted by our technician - all the track pads, the hold-down belt, the pressure roller, and likely a glue pot rebuild. Estimated cost for these parts, not including labor is $5600. The replacement of these parts is NOT included in the machine price.

HOMAG KL 78/A20/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: 0.4 - 20 mm ( 0.02" - 0.78") Edge thickness cap., min. panel width 55 mm (2.18") for panel thickness 12 - 22 mm (0.5" - 0.875") and under; 100 mm (3.9") for panel thickness over 22 - 60 mm (0.875" - 2.3"); for up to 3 mm Coil stock, HPL, and strip stock up to 20 mm (0.75").Feed & Infeed Section of Machine: -- Top pressure beam with: Double-wide compound V-belts; 80 mm wide feed track chain plates, vulcanized rubber insert pads, and Auto-Lube; variable feed speed from 18 - 24 MPM (59 - 79 FPM); 950 mm height/working level infeed. -- Pre-Milling Station with: (2) 3 kW - 150 Hz, 9,000 RPM Motors, panel blow-off device; 2-position infeed fence (on/off), SIKO digital manual fence control. -- Panel Pre-Heater with: Quartz lamp for heating substrate edge before glue application. -- Edge Feeding device equipped with: Automatic coil magazine for quick coil changeover; strip feeder for up to 20 mm (3/4") solid wood banding. -- "Quick Melt" Glue System with: Reversible glue roller applicator; pressure roll section with (1) large dia. driven and (6) idle rollers; manual adjustment of pressure zone through SIKO digital counters for different edge thicknesses.Edgebanding Workstations: -- Double motor front & rear end trim, straight & chamfer trimming (0.8 HP - 12,000 RPM ea. motor). -- Top & Bottom flush trim (2 HP - 12,000 RPM ea. motor). -- Corner rounding unit: Equipped with (4) motors, 2 HP - 12,000 RPM each motor. -- Universal Milling/Grooving Unit tiltable 90°. -- Edge Scrape Super-Finishing unit for thick PVC/ABS with chip collection box. -- Top & Bottom Flat Glue Scraper to remove potential glue squeeze-out. -- Top & Bottom oscillating buffing unit (two 0.33 HP - 1,650 RPM motors). -- "HOMATIC NC 21" controller features with Keypad & LCD display, stores working programs and controls functions of workstations, allows fault diagnostic and more, etc. -- Complete with: PLC controlled, motorized beam height adjustment; servo adjustments on Top & Bottom flush trim, and servo controlled Scraper Stations. -- Electronic DC brakes on all trim motors, sound cabins for all trim workstations, and adjustable outboard panel support. -- Actual Model is HOMAG KL 78/A20/S2.

- Min. panel height 0.47 inch - Max. panel height 1.57 inch - Min. edge thickness 0.01 inch - Max. edge thickness 0.24 inch - Max. forward feed speed 82.02 ft/min - Top pressure with rubber belt - No. Panel Sizing / Milling units 2 Pre-milling unit - Lamps to preheat the side of the panel - Edge coil magazine - Gluing system - glue pot for EVA hot melt glue - premelter for EVA hot melt glue - QA65 - Roller set to press the edge - no. pressure roller 7 - with positioning by NC No. Edge Processing Units 6 First Processing Unit - End trimming Constructor model HL81 - no. motors 2 - with positioning by NC Second Processing Unit - top and bottom rough trimming - no. motors 2 - with positioning by NC Third Processing Unit - Multi Function trimming and corner rounding - Constructor model - FK11 - no. motors 2 - with positioning by NC Fourth Processing unit - edge scraping - with positioning by NC Fifth Processing Unit - glue scraping - with positioning by NC Sixth Processing Unit - buffing - no. motors 2 Spray unit Control system Power Touch

HOMAG AMBITION 2270 (aka KAL 210) Edgebander with Pre-Milling & Corner Rounding:Specifications & Features: 0.4 - 3 mm Edge thickness cap., min. panel width 55 mm (2-1/8") for panel thickness 12 - 22 mm & under; 100 mm (4") for panel thickness over 22 - 60 mm.Variable feed speed from 8 - 25 MPM (59 - 79 FPM); 80 mm feed trackpads, and V-groove belt on top pressure beam which is motorized; motorized raising & lowering of top pressure beam through program selection.Pre-Milling Station with: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blowoff device and SIKO digital counters for adjustments. Edge Feeding Device with: 2-Coil vertical magazine for quick coil changeover.Gluing System suitable for PUR & reg; with: Pre-melt hopper feeder & roller applicator (reversible). Servo Controlled Pressure Roll Section with: (1) Large 150 mm dia. driven & (6) idle rollers; automatic Servo adjusting pressure zone through the program for varying edge thicknesses.Workstations:Double Motor End Trimming: 0.18 kW (0.24 HP) - 200 Hz, 12,000 RPM Motor ea.; to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip.Top & Bottom Flush Trim Unit with: Height adjustment with the top pressure and swiveling range +/- 1° (2 HP - 12,000 RPM ea. motor). Profile Trimming Unit with: (2) Motors to process the edge overhangs at the workpiece upper and lower edge, as well as trimming around the front & rear edge (0.75 HP motor ea.). (4) Motor Corner rounding station.Edge Scrape Super Finishing Unit for thick PVC/ABS. Top & Bottom Oscillating Buffing Station.

HOMAG EDGETEQ S-500 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.3 - 20 mm (0.011 - 7/8") Edge material thickness; 8 - 60 mm (0.3' - 2.375") panel thickness; 160 mm (6.375") min. panel length and 70 mm (2.75") min. panel width.High flexibility is achieved as all edge materials can be processed: 0.3 mm Melamine, up to 3 mm ABS, PP, PVC and wood as coil material.Solid wood strips and veneer strips up to 12 mm are fed in individually and up to 20 mm from the package. Even veneer strips of up to 1 mm can be fed from the package.For perfect high-gloss parts, important components such as the motor-driven top pressure and the automatic adjustment of the glue joint scrapers are used.Special tracing elements are ideal for processing of acute angled or obtuse angled parts or parts with hinge holes and transversal grooves.Variable Production Feed Speeds from 16 - 30 MPM (52 - 98 FPM). -- Equipped with: Separating agent spraying unit. -- Premilling Station: (2) Motors @ 2.25 kW (3.0 HP), 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Infeed fence with Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine for strip & coil stock, strips 0.4 mm - 12 mm (0.015 - 0.47"), coils up to 3 mm PVC with "HD" guillotine. -- "Quick Change" Glue Tank for maintenance, glue type & color change. -- Pressure Section: 1st. Roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- HOMAG "PowerTouch control, memory: 256 MB RAM, 1 GB Flash Card Drive. -- Workstations: End Trimming: (2) Motors @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Multistage MS40 Flush/Bevel-Fine/Radius Trimming Unit:Top/bottom: (2) Motors, 0.55 kW (3/4 HP) - 12,000 RPM, auto-tilt positioning 0° - 25°; with combination flush/radius/chamfer cutterheads. -- Multifunctional trimming unit MF60 Servo trim - Horizontal and vertical tracing wheels, equipped with brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes (3) positioning options: Profile 1, profile 2, and flush trimming; nested top copy system. -- Corner Rounding Unit: (1) 0.35 kW (1/2 HP) - 12,000 RPM Motor for leading & trailing edges, vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, multi-profile (PVC): Top/bottom with (2) profiles (1 mm and 2 mm or 3 mm instead of 2 mm), Servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Flat Glue Joint Scraping Unit: Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: Top & bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. -- Operator Control: HOMAG powerTouch2 control with clearer structure, 30