|
AMERICAN WOOD DRYER Direct-Fired Lumber Kiln - New, still at MFG' place:Now offered at 20% discount off the original cost and complete with the following main components and features: -- 20’ x 54’ in size, 39,000 Board Foot (92.03 Cu. Meters) capacity or 62,100 linear feet capacity, Package Type, Front Loading, Dry Kiln Building features: -- Gable Roof. -- R-20 Insulated ALCLAD Aluminum Panels, stainless-lined. -- Fan Deck Grating. -- Motor removal equipment. -- Drystar® Computer Control System, single head zone with (4) Rtds. -- 10 MM BTU/Hr. Natural Gas Fired Furnace. -- Kiln control and furnace Room approx. 20’ x 30’ x 11’ high on lowest side. -- (12) Steel lumber backstops. -- (7) 20 HP Air Circulation Fans. -- (7) SIEMENS Variable Frequency Fan Drives for 20 HP Fans. -- Accu Spray air atomized cold water Spray System with (7) Spray Nozzles. -- Insulated Door mounted on overhead track.The following $-figures show the distribution of funds applied to the original purchase price of nearly ...$466,000: ● Kiln with Gas Fired Furnace: ...$391,310 (The furnace itself is approx. ...$100,000.) ● Control System: ...$16,540 ● Furnace Room: ...$33,145 ● Backstops: . ... $ 5,400 ● VFD’s: ...$14,500 ● Water Spray: ...$ 5,100NOTES: ● The manufacturing of this equipment is nearly complete but halted pending the sale to allow for new Buyer to make any modifications desired. The price offered includes balance payment due upon completion unless modifications are requested by Buyer. ● The equipment is located at AMERICAN WOOD DRYER, LLC, Clackamas, Oregon. ● Installation by the manufacturer can be acquired directly from AMERICAN at Buyer’s option. ● Warranty offered by AMERICAN WOOD DRYER as part of the factory installation. ● Building shown in photo is representative only, not the one for sale here.
Equipment Location:PACIFIC NORTHWEST
Bill Christoffersen
800-374-5009 ext:365
|
|
Machine Number: 1750
Machine Type: Dry Kiln
Manufacturer: Kilntek
Model #: Dry Kiln
Location: South East
Kilntek Lumber Dry Kiln
Call For Details
Equipment Location:Blowing Rock, NC
Carolina Used Machinery
828-773-2204
|
|
Lumber Dry Kiln with a total capacity of 122,000 board feet and the following major components and features: -- (2) KATRES AFK 61,000 BD. Ft. aluminum link chambers, 45' wide X 80' long X 26' high. -- (8) 0.5 HP Bi-directional computer controlled circulation fans. -- (2) 10 HP BECKETT blowers. -- (2) NYLE HT 108 dehumidification drying systems with (2) 40 HP compressors each. -- (1) 40 BHP BOILERSMITH oil fired boiler and BOILERSMITH receiver pump. -- These are forklift loaded kilns and price includes loading for transport. Buyer responsible for freight.These units are dissassembled and in storage.
Equipment Location:EASTERN CDN
Bill Christoffersen
800-374-5009 ext:365
|
|
NYLE 30 (Similar to the newer HT42) Dehumidification Drying System:Complete packaged Dehumidification Drying System ready for installation into custom-built drying chamber. -- Designed to operate effectively at low humidity levels. -- The Model 30 has a load design capacity of 20,000 to 60,000 board feet (depending upon species and moisture content). -- Design temperature range of 80° to 160° F. Removes more than 2 tons (4,200 Lbs) of water per 24 hours.Complete with the following features: -- Nearly New CARLYLE 30 HP Compressor with latest Refrigerant specification. -- (5) 3 HP Circulation Fans. -- 7.5 HP Internal Blower. -- PARTLOW Chart Recorder, Model MRC 7000. -- Aluminum Cabinet. -- Copper Coils. -- Still in-place in good operating condition. --NOTE: Adjusted price now includes refrigerant pump-down, machinery removal, and loading onto Buyer's truck.This is a great unit with a huge capacity the same as the newer Model HT42.
Equipment Location:ATLANTIC CDN
Bill Christoffersen
800-374-5009 ext:365
|
|
NYLE L1200S Dry Kiln Heating unit -- Complete packaged dehumidification drying system ready for installation into custom-built drying chamber. -- Designed to operate effectively at low humidity levels; can bring moisture content to as low as 6%; patented "XDH" Control System is housed in a corrosion resistant, epoxy coated aluminum cabinet and operates over a wider range of temperatures with greater efficiency than any dryer available. -- The L1200S has a load capacity of (10,000 to 30,000) board feet (depending upon species and moisture content). Equipped with: -- 15 HP Compressor; a 3 HP internal blower; 48 kW of electric auxiliary heat. _ -- (4) 2 HP 30" dia. circulating fans; Fan reversing feature; (2) automatic over-temperature vents. -- Design temperature range of 70° to 160° F; removes 1250 lbs. of water per 24 hours. This unit is new and still in original crate!Now at a reduced price!
Equipment Location:EASTERN CDN
Bill Christoffersen
800-374-5009 ext:365
|
|
NYLE Model L300 Dehumidification Kiln. A packaged drying system ready for installation into a custom-built drying chamber complete with the following components and features: --(3) Reversing 0.5 HP Circulation Fans. --Electric Heater. --Wet Bulb, Dry Bulb. -- Over-temperature Exhaust. --3 HP Compressor. --1 HP Blower. --NYLE Design temperature range of 70° - 160° F; removes 420 Lbs of water/(24) hours. -- Designed to operate effectively at low humidity levels; can bring moisture content to as low as 6%; --The "L300" has a Load Capacity of 2,500 - 8,000 board feet and is equipped with: 3 HP Compressor, 1 HP internal blower and 8 kW electric auxiliary heat. --NOTE: No building provided. Chamber plans available.
Equipment Location:NORTHEAST
Bill Christoffersen
800-374-5009 ext:365
|
|
Brand NEW, Never Installed, NYLE Model L500 Dehumidification KilnComplete with the following standard components and features: -- (5) Reversing 5 HP Circulation Fans; -- Electric Heater; -- Wet Bulb, Dry Bulb; -- Total Amps: 72; -- 5 HP Compressor; -- 1.5 HP Blower; -- Design temperature range of 70° - 160° F; removes 720 Lbs of water/(24) hours; -- Load Capacity of 4,000 - 15,000 board feet. --This unit has been stored inside and has been checked. It is in untouched new condition.Note: -- No building provided. Chamber plans available.
Equipment Location:PACIFIC NORTHWEST
Bill Christoffersen
800-374-5009 ext:365
|
|
4' X 9' All Steel Kiln Carts Wheel Diameter- 8"
Wheel Width- 2 1/2"
72" Between Wheels. Quite a few have the Adjustable Wheels Just need to drill new holes
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
80+ Acres of land
Multiple buildings
Rolling stock: 10+ 3,000-6000 lbs forklifts, 8+ Taylor yard lifts
Dry Kilns: 23 Dry Kilns, each with a capacity of 100,000 BDFT
Multiple rough mill stations: Unscramblers, grading stations, stackers, trims saw
Flooring operation: Complete flooring operation includes: Two identical lines with rips saws, side matchers, end matchers, all conveyors, dust collection, optimizing line, sorting area
Finishing line: Complete stain line with lumber unstacker, sander, stain line, dryers, packaging area
Equipment Location:NC
Carolina Machinery Sales, Inc
704-288-1904
|