Woodworking Equipment For Sale

Brandt Optimat KDF 230C Edgebander

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

Brandt KDF 650 Edgebander

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Min or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. -- Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT - KDF 660, ...Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

Brandt Ambition 1110 Edgebander

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT F-13 Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL and veneer edgings, up to 3 mm max. thickness. -- Manually operated, 1/2" - 2-1/4" panel thickness, 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each); -- Built-in air jet blowoff device, 31" x 48" table size, and dual foot pedal controlNOTE: Intermittent fault in the control panel, which will require replacement.

BRANDT KDN-530C Single-Sided Edgebander, with Corner RoundingNOTE: Seller purchased new in crate in 2010 & all workstations are adjusted by servo motors.Specifications: -- Edge thickness 0.4 - 6 mm (0.02" - 0.24"). -- Panel thickness 5/16" - 1-5/8", Min. panel length 160 mm (6.30"), Min. panel width 65 mm (2.56"). -- Feed speed 36 FPM.Equipped with: -- Line control (No limit switches) for workstation function. -- Automatic height adjustment, with Top pressure beam for all workstations & Digital height indicator for 8 mm - 40 mm (0.31" - 1.57") panel heights. -- "POWER CONTROL PC-20+" Control, with PLC (Programmable Logic Control), VGA Screen, Touchpad, & Internal modem for remote diagnostic link, Signal infeed light to insure proper spacing between panels. -- Quick heat-up glue system, Heat-up time approx. 12 Min., with Glue tank for maintenance & Glue color change, Glue temperature indicator for both glue pot & glue roller with LED thermostat, Automatic temperature setback if machine is idle for 15 Min., Glue applicator roller is reversible & retractable from fence line. -- Automatic magazine for strip & coil, 800mm Dia. (31.50") Coil table accommodates large coils of 3 mm (0.12") PVC stock, 3 mm (0.12") PVC Guillotine. -- (1) Drive plus (1) Split secondary roller pneumatically-controlled pressure sections. -- 3 HP Feed motor.Workstations: -- End trim unit, with 1/4 HP - 12,000 RPM High-frequency motors with Electronic brakes, Chamfers 0° - 15°. -- Top & bottom flush/radius trim unit, with 1/2 HP - 12,000 RPM High-frequency motors with Electronic brakes, Bevels 0° - 15°, with Insert knives for 3 mm (0.12") PVC radius & "Quickset" with Digital counters. -- Single-motor corner rounding unit, For "On-the-fly" corner rounding, with 1/2 HP - 12,000 RPM Motor. -- Top & bottom scraping unit, For 3 mm (0.12") Radius, with Pneumatically-controlled indexing system & Dust collection. -- Top & bottom buffing unit, with 1/4 HP - 2,800 RPM Motors.Complete with: -- Manual.NOTE: Seller estimates he has run 70,000 parts on machine.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: -- PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Minutes or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. --Complete with:Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT AMBITION 1650 FC HIGH FLEX EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): Specifications: -- Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units.Equipped with: -- 3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High-Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 KW, 3 KG (6.61 Lbs.) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- QA 45 Quick-change glue tank with electronic switchable/emptying mode for easy maintenance & glue color change.Melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Adjustable glue amount with servomotorPressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electropneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") ma

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

Brewer Step Planer 24in, BR425, S/N 12286, 50HP Electric Motor Up to 6" thick

Brewer BR-425 Step Planer

16” Width Capacity Approx 15 HP Top Head Approx 10 HP Bottom Head Feed 23-65 FPM 220 Volt 3 Phase

BRIDGEWOOD BW-511MS Sliding Table Shaper Single Phase 4 HP Motor with forward & reverse.Specifications: -- 3/4″ Spindle with 4-1/2″ under the nut, and 3-1/2" of Spindle travel. -- (5) Spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. -- 52" Table Length, and 35 Sliding Table Length1-used BRIDGEWOOD BW-511MS SLIDING TABLE SHAPER. Table Length: 35″, Sliding Table Length: 52″, 3/4″ spindle with 4-1/2″ under the nut, Also , Spindle Travel: 3-1/2″, Motor: 4 HP, single phase, (5) spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. For operation on 220V, 1PHNote- the feeder in the photo is not included

20" Width cap., 1/4" - 9" opening, 7.5 HP motor (3-phase) with 1.5 HP feed motor, both made in the USA, variable feed speed 20 - 32 FPM.Complete with: Segmented infeed roller, cast iron chipbreaker and adjustable bed feed rollers; 3-knife cutter with jack screw adjustment. - Includes (2) sets of knives.