Cutler-Hammer For Sale

Weinig Unit 318 Moulder 9" Machine 6-Head Low hours! Also available: Weinig R960 Grinder and tool room

Weinig R950 Profile Grinder

Weinig R960 Profile Grinder Measuring Stand Complete tooling room included!

270 Ton WEMHONER - 110"; L to R x 59"; F to B Down-Acting Hydraulic Press: Model KT-M-15/28-240. Clearance between frame is: 126"; L to R x 37"; F to B. -- Nominal bed: 110"; x 59";. -- 4-Clamp Cylinders are single-acting: Approx. 8"; Bore; 6"; dia. rods; approx. 10"; max. stroke. -- (1) Center traversing cylinder: Approx. 3" bore with a 1-3/4" diameter rod (approx. 16 max. stroke). -- Max. daylight: Approx. 16";. -- Approx. 28-1/2"; Operator height. -- Guided with rollers at each corner and (2) gear & rack guides. -- Slide and bed: 4" Thick; self-contained Hydraulic System: -- (2) Reservoirs: Approx. (14) gallons each. -- 4 kW Motor: Approx. 5 HP; 1,800 RPM, 440 Volts, 9.15 Amps. -- Pump: Type "R60A; max. 350 Bar, etc. -- Speeds: Approx. 99 IPM fast down; 2.0 IPM Pressing adj; 99 IPM fast up. -- NO Electrical Controls. -- Overall Dimensions: Approx. 146"; x 65"; x 96"; high. -- Approx. 30,000 Lbs.

Wemhoner Variopress

West Salem model 2420GR1-H wood grinder/hog 480 v Bottom discharge No screen - machine has breaking bars Disconnected and ready to ship

WESTERN PNEUMATICS FJW2VS24 Heavy Duty Production Finger Jointer. Right & left shaper section. - Cap.: 5/8" - 2" Max. thickness, 1-1/2" - 8" max. width, 5" min. - 36" max. length.Equipped with for right and left side: -- (2) Scoring saws, 7-1/2 HP - 3,600 RPM motors, -- (2) trim saws, 7-1/2 HP - 3,600 RPM motors, --(2) shaper motors, 20 HP - direct drive 3,600 RPM motors. -- 6" Wide WESTERN feed chain, angle transfer conveyor and 15 HP variable speed drive with speeds up to (120) lugs per minute. -- Air Bag Pressure Head with quick change feature & brush holddowns -- APQUIP extrusion type glue applicator with meter mixing system -- Transfer to the assembly press via powered manual corner transfer -- 17' Extra length Assembly Infeed Conveyor with electronic ramp up/down infeed package, powered side alignment rolls and top and bottom pre-assembly rolls. -- Assembly Press: 24' (to be confirmed) finished board length, hydraulic squeeze board press and board ejection; with rapid stop-and-chop 7-1/2 HP heavy duty cutoff saw. With automatic cycling, -- Feed speed varies automatically depending on block and cutoff lengths, 50 - 200 FPM.Pieces advance through the cutoff saw to a moveable limit switch and are cut to length, arranged for continuous assembly, the cut to length piece drops down into a final squeeze chamber while the next piece is cut to length, finished lengths are pushed out hydraulically by the next piece onto material outfeed arms.Includes: -- Set of cutterheads and knivesNOTES: -- Machine for factory rebuilt in 2009 -- Machine will easily run 120 lugs per minute and 200 FPM at the Press -- Equipment has been maintained to factory standards since new -- Parts replacemnnt (feed chain, sproket, fences and more) in 2018 for a total of $28,500 -- Taken out of service in January 2025Riggers are required for loadingSome technical information needs to be confirmed by seller

WESTERN PNEUMATICS HEAVY DUTY FINGER JOINTER WITH THE FOLLOWING EQUIPMENT & FEATURES: -- Right & Left Shaper Section: Thickness Capacity: 3/4" - 2" maximum; Width Capacity: 1-1/2" - 8" maximum; Length Capacity: 5" min. - 36" maximum; -- (2) Scoring Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Trim Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Shaper Spindles are hydraulically powered; direct driven @ 3,600 RPM by -- (1) 60 HP Hydraulic Power Unit with (1) cartridge unit per spindle. Hydraulic conversion was performed during the first year of operation. -- Western's 2-1/2" wide feed chain with lugs on 9" centers; 15 HP variable speed drive with up to 120-lug per min feed speeds; with angle transfer conveyor, air bag pressure head with quick-change feature & brush hold-downs -- APQUIP Extrusion Type Glue Applicator complete with mixing system. Currently arranged for 3/8 finger joints including (4) 3/8" glue combs -- Manual Corner Transfer to the assembly section. (allows for inspection and rejection of blocks for poor joint quality, missing proper glue spread, etc. prior to going into assembled boards) -- 12' Pre-Assembly Infeed Conveyor with feed speed ramp up/down; with side alignment rolls and dual top and bottom pre-assembly rolls -- Flying Cutoff Saw operating from below -- Assembly Press: 20' board capacity with hydraulically powered press -- Automatic Cycling Assembly Section: Feed speed varies automatically from 50 to 200 FPM, depending on incoming block lengths. Boards advance through the Cutoff Saw to a moveable limit switch where they are cut to length with a bottom-mounted 7-1/2 HP Flying Cutoff Saw arranged for continuous non-stop assembly. The cut to length board drops down into the squeeze chamber while the next board feeds out and above the preceding board where it is cut to length. Pressed lengths are pushed out onto material outfeed arms by the following board

WHIRLWIND 1000 R 14” Right-Hand Semi-Automatic Pneumatic Upcut Saw Specifications: Cutting cap. 2-3/16" x 8-1/4". Work area 12” x 22” x 36-1/2” H. Arbor dia. 1”. Blade speed 3,450 RPM. Cycle speeds 5 - 90 Cycles/Min. Equipped with: 5 HP - 1,740 RPM - 208 - 230/460 Dual voltage motor. 20-1/2” L x 1/2” H” Aluminum fence. Built-in foot pedal control. Complete with: TIGERSTOP “TS-10” 10' L Automated Material Pusher/Stop, S/N 1016705, with Overall length 12', 10” W x 12’ L x 36-1/2” H, Solid pusher/infeed table, 14-1/2” W x 10’ L x 36-3/4” H Solid outfeed table with 12’ L x 1-1/4” H Aluminum fence with scale, TIGERSTOP “CON5” Controller, with LCD Display, Touchpad, “VPK2” Software package (Optimization, Download, & Ethernet Connection), & TIGERSTOP “AMP5” Amplifier. Saw with Pusher/Stop Dimensions: 318” x 27” x 63” H. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Whirlwind Undercut Saw with Tiger Stop Fence

Whitney 105 Planer 24" Planer Used daily in current shop.

Whitney 105 Planer 24" Planer Used daily in current shop.

Williams 125 CJS1 Hammermill

Williams 125 HP Hammermill 230/460 3-phase

Model 206 For smooth moulding and planing; (1) 2 HP Baldor motor, 7,000 RPM spindle speed, variable feed rate of 1 - 19 FPM includes "Deluxe" variable feed control with magnetic drop out switch and cords. Built in Multi-Pass system and Guide sytem -- Capacity: Max. material width 7", material thickness from 3/4" to 8" max., min. 9" stock length. Max. profile depth 3/4" and max. profile width 6-3/4", planes 7" wide and can do a 7" radius with optional jig; working height 31", overall height 45", overall width 20". -- Includes: Table guides, dust hood, belt, pulley, planing knives, welded steel stand, custom moulding catalog, oil, and operator's manual. -- With OPTIONAL accessories like the elliptical jig you can make arches and elliptical mouldings, please add...$ 700. Also available in 115/1/60 and 230/460V/3/60. Weight: Approx. 242 Lbs.

Manufacturer’s Soecification Feed Type:0-19 fpm, variable feed Motor:2 HP (3450 rpm) Voltage:240V Maximum Profile Depth ¾ inMinimum Stock Length 9 inMaximum Profile Width 6 ¾ inMinimum Stock Thickness ¼ in Maximum Height Above Final Cut 3/16 in Maximum Stock Thickness 8 in Planes 7 in WideOverall Machine Dimensions:28 inL x 22 inW x 50 inHWorking Height:35 in

William & Hussey "W-7S" Moulding Shaper -- Specifications: 17-1/4"x 14" Table size, 2 HP main motor, 2-knife cutter head, 3,450 RPM spindle speed, 7" max. cutting height, 1/4" min. thickness 3/4" deep max cut.. Max moulding cap. 7" wide, max. planning cap. 7" wide. -- Complete with: Dust hood outlet, electrical disconnect, and mounted on fabricated steel stand w/casters, Multi-pass

Williams and Hussey 2007 W7-S model 206 planer/molder good condition Ser# 00452 Weight 250 ish Max thick 7”, Max width 7” Multi pass Baldor motor Powered infeed and out feed New std knives available at W/H for app 100/set Custom knives available from W/H

100 HP 230/460 volt 20” x 19” inlet 9” x 28” outlet no hopper