Woodworking Equipment For Sale

Barr-Mullin Opti Rip Wondersaw, optimizer w/computerized laser controls, Compu-rip scans the boards for width to determine the optimal cutting solution, floor space: 21'x5' (315 sq. ft.) Good condition. $14,950 or BEST OFFER

The Compu-rip scans the board for width to determine the optimal cutting solution which is projected onto the board via overhead lazers. Specification: Material Thickness up to 3” Material Width up to 31” Maximum output no limit Minimum output 4” Feed Height 34.5” Floor Soace approx.21’ x 15’ Power supply 480 volt 3-phase

BECKER VTLF 2.250 VACUUM PUMP (OIL-FREE VANE): -- Specifications: QTY (2) 7.5 kW (10 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System; -- Pump has 169 CFM total 338 CFM max. 25"Hg; Heavy Duty construction, compact design, small footprint. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; -- 2-1/2" BSP x 2" NPT nipple coupled to a TFC; 1,150 RPM motor. -- Complete Becker Pump Stack, VTLF 2.250, 10HP x 2.

BECKER VTLF 2.250 VACUUM PUMP (OIL-FREE VANE):Specifications -- (1) 7.5 kW (10 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System. -- Pump has: 169 CFM Total; 338 CFM max.; 25"Hg; Heavy-Duty construction; compact design; small footprint. -- 100% Oil-less Vacuum Pump is virtually maintenance-free with: Built-in carbon vanes & built-in suction filters; vacuum regulating valve; secondary suction for additional cooling; blow off valve/silencer. -- 2-1/2" BSP x 2" NPT Nipple coupled to a TFC; 1,150 RPM motor.

BECKER VTLF 2.250 VACUUM PUMP (OIL-FREE VANE):Specifications -- (1) 6.4 kW (9 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System. -- Pump has: 169 CFM Total; 338 CFM max.; 25"Hg; Heavy-Duty construction; compact design; small footprint. -- 100% Oil-less Vacuum Pump is virtually maintenance-free with: Built-in carbon vanes & built-in suction filters; vacuum regulating valve; secondary suction for additional cooling; blow off valve/silencer. -- 2-1/2" BSP x 2" NPT Nipple coupled to a TFC; 1,150 RPM motor.

BECKER KVT 3.100 3.6 Kw (5 HP) Vacuum pump:Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 69 CFM and 100 cm/Hr with max. 27"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer. -- Complete WithInlet vacuum air filter system.

Becker VTLF 250 Vacuum Pump: 9.3 kW (12 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, 176 CFM, max. 25"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; 2-1/2" BSP x 2" NPT nipple coupled to a TEFC; 190-255/330/440V, 1,160 RPM motorNote (2) unit available and the price is for each

"BECKER" VTLF 2.250 Vacuum PumpSpecifications: -- (1) 6.4 kW (9 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System; -- Pump has 169 CFM total 338 CFM max. 25"Hg; Heavy Duty construction, compact design, small footprint. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blowoff valve/silencer; -- 2-1/2" BSP x 2" NPT nipple coupled to a TFC; 1,150 RPM motor.

84" maximum opening; 9" minimum opening on 90° trim; (2) 3 HP trim saw motors; 16" dia. saw blade capacity; 1" diameter saw arbor; (2) 3 HP boring units (boring heads not included); saws and boring units tilt 10° up, 23° down and swivel 90° for simple or complex miter work; .5 HP motorized open and close; (2) pneumatic holddown clamps; saw and boring units upgraded to hydraulic control; 5 HP hydraulic pump; retrofitted with electric brake system

BENCHMARK 205-HP3 Hot Melt Adhesive ApplicatorHot Melt Adhesive Applicator with: -- Bodine adjustable speed motor. -- Bead dispensing applicator. -- Also includes an extra Bodine adjustable speed motor regulator, for fine tuned glue application.

Bertheson Press Platform size 51 Wide X 102 Long with 2 16 ft shuttle driven aluminum runner platforms. Pressure 2500 psi and we ran a temperature of 350 degrees for Tego and 165 degrees for plywood. The Press can laminate Tego Film glue or pva c glue. This press is a double shuttle and can laminate up to 14 ft by double pressing on shuttle. We can get the press operational if you are interested. We only have to hook up the power. Very good condition!

--This machine is in an Auction on exfactoryauctions.com--NO RESERVE-- (2 Available) BIESSE SKIPPER 100 2-Head CNC Machining Center, with Infeed & Outfeed Tables – Seller states that machine was run (2) shifts from 2005 - 2021, then only a few hours per day since! Specifications: Flexible "Top & Bottom" Machining Center that uses an innovative panel handling system. Working Capacity: "X" Axis 3,000 mm (118.11"), "Y" Axis 1,000 mm (39.37"), Max. part thickness 60 mm (2.36"). Min. workable part size: "X" Axis 90 mm (3.54"), "Y" Axis 70 mm (2.76"), & "Z" Axis 8 mm (0.31"). Work Table: Left-hand infeed & Right-hand outfeed, Each with 20-1/2” x 66” x 35-1/2” H infeed & outfeed areas with Fixed caster-type conveyor rails. Positioning Speed: "X" Axis 120 MPM (393 FPM), "Y" Axis 90 MPM (295 FPM), "Z" Axis 30 MPM (98 FPM). Boring Units: (1) Top & (1) Bottom boring blocks, Each with: 3 kW (4 HP) Motor, Boring spindle speed 4,000 RPM, (29) Vertical spindles with (17) "X" Axis & (12) "Y" Axis, (10) Horizontal spindles with (4 + 4) "X" Axis & (1 + 1) "Y" Axis, & (1) "X" Axis Grooving saw with 3 kW (4 HP) Motor, Blade speed 5,000 RPM, & Blade diameter 150 mm (5.91"). Machining: (1) Top & (1) Bottom 3.5 kW (4-3/4 HP) Electrospindles, Each with: Variable spindle speeds 7,000 - 18,000 RPM, Right-hand/Left-hand rotation, HSK D-50 Adapters for Manual push-button quick tool change, ERC-32 Toolholders & RC-32 Collets. Operator & Machine Control: Mobile Control Console, with PC-Based Control, 18" LCD Monitor, BIESSE "WORKS" + "WINDOWS" Operating system. Pedestal & Pendant controls. Equipped with: Universal transformer, 200 - 600 V, 50/60 Cy, 3-Ph., Automatic lubrication system for guides & ways, Sound hood, 79" H Safety fence with Lock-out door, & TAPESWITCH "CONTROLMAT CKP" 24" x 72" Heavy-duty ribbed pressure-sensitive safety mat. Complete with: 7’ x 9’ x 35-1/2” H Infeed Table, with Rails & Pusher. 6-1/2’ x 8’ x 35-1/2” H Outfeed Table, with Transfer Belts. Handheld Bar Code Reader. Dust Manifold. Dimensions including Safety Fence: 307" x 184" x 98" H.

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).

BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback"; of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Work stations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).

BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm Material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback"; of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Workstations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).

Biesse Rover B Edge semi automatic pod setting 4 coil magazine vertical and horizontal drill bank main spindle with U axis Milling X1: 5055 mm Y1: 1600 mm Edgebanding X2: 4100 mm Y2: 1600 mm Milling Module H74 - Z1: 245 mm Module H29 - Z2: 290 mm

Biesse Levia 310-1350 Sander

Biesse Akron 245 Edgebander System is still under power until approx mid-October 2024. Touch PLC will need to be replaced. Everything else is working good on the machine. Owner has had it serviced by Biesse.

Manufacturer Specs premill hot glue end trim top/bottom trim corner rounding scraping buffing Computer interface