Woodworking Equipment For Sale

Model P30N 600 V / 3 Ph / 60 Hz Includes Transformer

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

4 Head drill station 20' with powered roll case Hydraulic set stops

PHI IR-3 Preheater;Overall dimensions 5' wide x 4' long, consisting of: (3) IR Medium Wave heating banks, each 1" wide x 54" long, bank has gold foil quartz heating elements.This IR unit is designed to preheat the board to facilitate out gassing and help eliminate solvent pop and air bubbles in the coatings of deep pored materials such as oak. Also used to standardize board temps during colder months as well as decrease dry times of other substrates. These units are primarily (but not exclusively) designed for use before the application of stain and sealer coats. Features: Explosion proof electrics, electrical heat temperature adjustable from 100° - 150° F, variable feed speed from 8 - 30 FPM (2.5 - 9 MPM).

PILLAR - H49: CNC Bore, Glue & Dowel Inserter -- Specifications(2) Working zones and overall, 49" max. width capacity.(1) CNC Controlled head assembly with: Rapid (side-to-side) traverse; assembly with boring, gluing & insertion unit; 1 HP - 18,000 RPM drill motor.(4) Vertical pneumatic hold down clamps; function selector control for boring only or doweling, adjustable drilling speed.1-9/16" (40 mm) Max. dowel length; setup for 8 mm dowel dia.; height adjustment up to 1-1/8" material thickness with digital readout. -- Operator InterfaceCNC "Color Touchscreen" Controller for: Function & part programming and program storage. -- Complete with:(1) 12" Dia. vibratory feed hopper: Totally sealed electronically metered glue system with 1-button flushing.100 PSI High power glue pump; 2-1/2-gal. glue tank; anti-slip table surface; 49" X-axis cap.Rack & pinion drive; centralized dust collection manifold.

PILLAR MACHINE HPLD 96" CNC BORE & LOCK-DOWEL INSERTER: -- Specifications:(4) Working zones of 24" each and "OPTIONAL" working table length of 96"; CNC controlled head assembly with rapid (side-to-side) traverse.Head assembly with: (1) Horizontal boring & insertion unit with a 3 HP - 18,000 RPM Direct-Drive Spindle motor; "X" Axis is servo controlled for positioning; Digital Mechanical Readouts for Height and DepthHead is currently set up to bore/machine/insert 20 mm Lock-Dowel "Eclips", H-clips, Channel Locks & 8 mm Spring Pin Fasteners.Material thickness capacity 0.5" - 1" max. Material thickness with digital readout for height adjustment. -- Clamping System:(8) Pneumatic, quick side-to-side adjustable hold-down clamps for horizontal "Lock-Dowel" processing on the panel edge.(1) Pneumatic Clamping Bar for vertical boring into the panel face/back. -- Operator Interface:15" Color Touchscreen control + Windows 10 Operating System. Ethernet 1 x PCIE Broadcom GbE (or similar), USB: 2 x USB 2.0 (or similar), Serial Port: 1 x RS-232 (or similar)The on-screen graphics of the operator interface have been designed to allow for quick programming at the machine. Typically, programs can be written and recalled in less than one minute.The Interface is open architecture allowing it to integrate with design software that can give hole locations in the form of a .xml file or a bar code (with bar code reader purchase found in options).Standard Features in the software include: 1. Graphic interface to show where holes are to be drilled and if a dowel is to be inserted. 2. Pattern Drilling/Inserting.3. Password protection of certain features/functions. 4. Online diagnostic capability (if machine is connected to an internet connection). 5. Toggle between Metric or Imperial programing parameters. -- Features: This machine will insert H-clips, Channel Locks and Spring Pins with ease. Using CNC control, this machine positions the drilling spindle to bore holes and insert the Lock dowel hardware. -- Complete with:Anti slip table surface, rack & pinion drive, and centralized dust collection manifold. -- Actual model is: PILLAR MACHINE HPLD

PINHEIRO PMC 4-450 Four Sided PlanerSpecifications: -- 18" x 6" Max. cap. motorized opening, -- Top head 18 HP, -- Bottom head 12 HP motor, -- Both side head motors are 9 HP; -- All spindles 40 mm dia.; -- Digital readouts on top and outboard left spindles, 5" max. tool dia. -- Max. profile depth of side heads 1" max. -- 5 HP Feed motor, (6) feed speeds between 10 & 75 FPM, (To be confirmed) -- (4) powered feed rolls, sectional feed rolls, sectional chipbreaker, central lubrication system. Includes: -- Sound hood, Star Delta motor starters,

The seller has confirmed that this Pinheiro planer is in good working/running condition. - Double sided planer with side saw - Complete package - Manual - no year...Motor HP 20 bottom, 10 top

(2) 2-1/2 HP motors 5/8” arbors 12” blade capacity max width 3 - 5/16” nax depth 2-5/8”

12” blades 1-1/2 HP motors - 3 phase foot pedal control

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil 13.5 460-10 304 Stainless Steel Reverse Air Bag House, 5,922 SQ/FT Cloth Media, 47,000 CFM @ 8:1 Air/Cloth Ratio, Very Good Condition, $82,000.00

Porter Planer Model 700 S/N 5916, Straight Knifes 10HP Motor

POWERMATIC - WB-25, ...Wide Belt Sander1-Head; 25" width capacity; 1/8" to 6" thickness capacity.Combination sanding head with: 4" Dia. rubber-covered contact roll; 2" wide polishing platen; micro-adjust platen; steel abrasive belt tension roll; steel idler roll: 25" x 75" Abrasive belt capacity.Equipped with: -- 15 HP 3-Phase main motor; 1 HP variable feed motor, 15 - 49 FPM. -- 1/4 HP Table raising & lowering motor with: Auto adjust thickness assist; 1/8" to 6" opening with (4) screw jacks. -- Double infeed & outfeed rubber covered holddown rolls. -- Complete with: -- Digital readout; air eye belt sensing; limit switch overtravel protection; magnetic starter; overload protection; load meter; emergency brake.Includes: Owner's manual & parts list.

TABLE SAW TOP MEASURES 44" WIDE X 76 ½" LONG TABLE HEIGHT FROM FLOOR 34% " COMES WITH 5 - 12" DADO BLADES 1 HORSE POWER POWERMATIC MATERIAL FEEDER 5 HORSE POWER SAW ARBOR MOTOR 440 VOLT 3 PHASE

20" Dia. dynamically balanced aluminum disc, 3 HP - 1,740 RPM direct drive motor; 15" x 27-1/4" table w/miter gage slot, tilts 30° upward & lowers 45° downward, 90° positive table stop; rack mechanism for raising & lowering table by hand crank, heavy bolt-down steel base. Complete with reversing switch and miter gauge. Also available in Single-phase in 2 HP motor.

Powermatic PM-37 Wide Belt Sander Specifications: -- 1-Head, 37" width cap., combination sanding head with 4" dia. rubberized contact roll & 2" wide polishing platen; 20 HP motor. Power raise-and lower with 1/2" HP motor. -- Abrasive belt size 37" x 60", air tensioning, electronic abrasive belt tracking; 2 HP conveyor with variable speed feed - 18 - 72 FPM, 0" - 5" opening with (4) screw jacks, double infeed & outfeed rubber-covered hold-down rolls. Digital read-out displays thickness. Minimum board length 10-1/2". -- Complete with: Infeed conveyor extension, safety stop bar, 6" dust port, and load meter. - Includes owner's manual, tool kit and parts list.

POWERMATIC - WP 2510: PlanerThe POWERMATIC "WP 2510" Planer includes: 15 HP Motor, solid steel helical cutterhead with 4-sided carbide knife inserts that require no adjustments when changing. With a digital readout & simple PC controller, setting up table heights is quick and easy. -- Frame is: Machined from Heavy cast iron; extra wide side panels offer rigid bed support & accurate alignment. -- The WP 2510 has: Segmented, serrated infeed roll with segmented chipbreakers; independent yield of 1/4"; automatic adjusting; chain drive gear box; 3" dia. infeed rollers, solid pressure bar; dual outfeed rollers for precise feeding of stock. -- The 3-speed feed selector gives woodworkers flexibility by changing feed rates quickly and easily. -- Equipped with: Large 32-3/16" x 26" Precision-ground table with (2) adjustable table rollers for smooth feeding of uneven stock.Includes Quick-Set micro-adjustable lever: Easily raises & lowers the table rollers from: 0 to 0.05".Hood features: Built-in 5" diameter dust chute. -- SPECIFICATIONS -- Max. planing: 25"; max. planing thickness: 9"; max. full width depth of cut: 1/8"; max. depth of cut: 1/4". -- Min. Planing length: 10"; cutterhead dia.: 3-3/8"; cutterhead speed: 5,000 RPM; cuts per minute: 30,000; 15 HP motor. -- Feed Rate: 20, 25 & 30 FPM; Outfeed Roller Diameter: 3"; number of Knives: (174) 4-sided inserts. -- Table Size: 32 3/16" x 26"; dust port diameter: 5"; dust collection CFM required: 600 CFM. -- Bed Rollers: Adjustable from front: 0" - 0.05"; readout scale: Inch/ metric; table height adjustment: Manual with (1) Turn = 1/32"; 2-column bed support, 2-1/2" column dia.; (1) infeed & (2) outfeed rollers. - Includes Tool Kit.

Powermatic 225 Thickness Planer.Specifications: 24" x 8" Cap., 15 HP cutterhead motor, 1.5 HP drive motor, variable feed speed from 20 - 100 FPM with forward/reversing switch.Features: sectional serrated infeed roller and sectional chipbreaker, (2) adjustable powered bed rollers; table size 24" x 48", with manual height adjustment. Complete with: Magnetic motor controls & 8" dia. dust hood.NOTE: The above specifications are taken from the Seller and literature and are considered accurate. As always, please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.