Woods For Sale

84" maximum opening; 9" minimum opening on 90° trim; (2) 3 HP trim saw motors; 16" dia. saw blade capacity; 1" diameter saw arbor; (2) 3 HP boring units (boring heads not included); saws and boring units tilt 10° up, 23° down and swivel 90° for simple or complex miter work; .5 HP motorized open and close; (2) pneumatic holddown clamps; saw and boring units upgraded to hydraulic control; 5 HP hydraulic pump; retrofitted with electric brake system

BENCHMARK 205-HP3 Hot Melt Adhesive ApplicatorHot Melt Adhesive Applicator with: -- Bodine adjustable speed motor. -- Bead dispensing applicator. -- Also includes an extra Bodine adjustable speed motor regulator, for fine tuned glue application.

Bertheson Press Platform size 51 Wide X 102 Long with 2 16 ft shuttle driven aluminum runner platforms. Pressure 2500 psi and we ran a temperature of 350 degrees for Tego and 165 degrees for plywood. The Press can laminate Tego Film glue or pva c glue. This press is a double shuttle and can laminate up to 14 ft by double pressing on shuttle. We can get the press operational if you are interested. We only have to hook up the power. Very good condition!

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

BIESSE ROVER A FT 1536 G FT FLAT TABLE MACHINE (W/LOADING, UNLOADING): -- Specifications:5' x 12' "Matrix" grid phenolic surface for "Nested Base Manufacturing", Front loading flow from Left to Right configurationAutomatic Loading and Unloading System (Sweeping Arm + Loading Vacuum cups) . -- Working capacity:"X" Axis 148.2" (3,765 mm), "Y" axis 61.4" (1,560 mm), "Z" axis stroke is 12.7" (324 mm), max. material thickness 6.7" (170 mm). -- Positioning Speed:"X" Axis 279 FPM (85 MPM), "Y" axis 197 FPM (60 MPM), "Z" axis 65.6 FPM (20 MPM);"X" & "Y" Axes use a precision rack & pinion system, "Z" axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing",(14) External pneumatic pop-up stops for piece positioning at 4 corners of workstations; Automatic NC controlled (9) zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2.5 HP (1.7 kW) motor, variable speed up to 6,000 RPM: BH18 Boring unit with (11) independent vertical spindles, (6) in "X" axis & (5) in "Y" axis.(4) Horizontal spindles with (1+1) in "X" axis & (1+1) i "Y" axis; (1) "X" axis Grooving saw for max 120 mm dia blade. -- Machining:(1) 16.1 HP (12 kW) Air cooled "HSD" Electro-spindle with HSK F63 adaptor, RH & LH rotation; variable speed from 1,000 - 24,000 RPM.((1) 16-Position ride along tool changer for "on the fly" ATC. NC controlled tool presetting for the measurement of the tool length -- Operator & Machine Control:PC Front End with: Biesse "BH 660" + "bSOLID" + "bNEST" + WINDOWS "WRT" (Windows Real Time) operating system;19" LCD Flat screen monitor; server, full keyboard & mouse all mounted on a mobile cart;Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; Dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities."bSOLID" allows to design the final product, defines machining, defines working table set-up, simulates the part machining in 3D & generates the programs."bNEST" allows to create nesting projects with related quantities to be produced and the list of boards to minimize the material usage & machining times. The optimization process result is a list of bSolid programs "bNEST" includes the following features: Manual nesting project creation, Data import from ERP or external design application is used in order to keep easy the data exchange between software applications. The imported data will be used for production and labelling as well. The import rules are configurable thus they can easily adapt to customer needs Dedicated environments where the operator can edit, check and fix all the information of parts, boards

Biesse Rover B Edge semi automatic pod setting 4 coil magazine vertical and horizontal drill bank main spindle with U axis Milling X1: 5055 mm Y1: 1600 mm Edgebanding X2: 4100 mm Y2: 1600 mm Milling Module H74 - Z1: 245 mm Module H29 - Z2: 290 mm

BIESSE ROVER B 4.35 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working capacity: "X" Axis is 125.9" (3,200 mm) any unit; "Y" axis is 51.7" (1,315 mm); "Z" axis stroke 6.3" (160 mm) max. material thickness is 5.9" (150 mm). -- Positioning Speed:"X" & "Y" Axis is 262 FPM (80 MPM) & "Z" axis is 66 FPM (20 MPM). -- Worktable:(6) Panel support rails with: (3) Vacuum pods per panel support; (4) pneumatic lifting bars for heavy panels.(2) Independent working areas with: (6) Front & (1 + 1) side pneumatic pop-up locating pins for positioning of parts on the worktable.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; each work zone with: (1) "Quick Connect" vacuum outlet for custom vacuum fixtures. -- Boring Unit:(1) 2.3 HP (1.7 kW) - 4,000 RPM Motor: (12) Independent vertical boring spindles with (6) spindles in "X" axis & (6) spindles in "Y" axis.(6) Horizontal spindles with: (2 + 2) in "X" Axis & (1 + 1) in "Y" axis; (1) "X" axis grooving saw for max. 120 mm dia. blade. -- Machining Unit:(1) 10.2 HP (7.5 kW) Vertically mounted HSD "Electrospindle" Router with ISO 30adapter, inverter driven 1,000 - 20,000 RPM with max. torque from 12,000 - 20,000 RPM.(1) 10-Position ride-along ATC for "on the fly" tool change. -- Operator & Machine Control:PC Front-End with: BIESSE "XP 600" + "BiesseWORKS Advanced" + Windows "WRT" (Windows Real Time) operating system; INTEL "Celeron" 2.0 GHz processor; 4 GB Hard drive.15" Color monitor, international keyboard, soft touch keypad & industrial mouse, RS-232 serial port, USB ports, CD ROM & 1.44 MB disk drives.Separate Control Panel with: Built-in 1,500 W air conditioner for constant temperature & dust-free environment; 11 KVA Stabilized autotransformer for voltages between 200 - 600 Volts. -- Complete with:(1) 100 cbm/Hr Vacuum Pump; centralized manual lubrication system for guides & ball screw; emergency stop rope; safety light barrier & sound absorbing protective head enclosure with debris curtain around bottom edge; scrap belt conveyor. -- Actual model is: BIESSE - ROVER B 4.35.

BIESSE ROVER B 4.40 FT FLAT TABLE MACHINE (W/ATC/BORING) -- Specifications:4' x 10' Flat Table with "Matrix" grid phenolic surface for "Nested Base Manufacturing". -- Working cap:"X" Axis 126" (3,200 mm), "Y" axis 53.5" (1,360 mm), "Z" axis stroke is 6.3" (160 mm), max. material thickness 5.9" (150 mm). -- Positioning Speed:"X" & "Y" axis is 262 FPM (80 MPM), "Z" axis is 98 FPM (30 MPM); helical rack and pinion drive on "X" axis & ball screw on "Y" & "Z" axis. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing", (2) independent working areas; (4) external pop-up reference pins with (3) on the back of the table & (1) on the LH side.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; each work zone with (1) "quick connect" vacuum outlet for custom vacuum fixtures. -- Boring Unit: (1) 2.5 HP (1.7 kW) - 4,000 RPM motor: (12) independent vertical spindles, (6) in "X" axis & (6) in "Y" axis.(6) Horizontal spindles with (2+2) in "X" axis & (1+1) in "Y" axis; (1) 120 mm dia "X" axis grooving saw. -- Machining:(1) 10.2 HP (7.5 kW) Electro-spindle with ISO 30 adaptor, variable speed from 1,000 - 20,000 RPM;(1) 10-Position ride along tool changer for "on the fly" ATC. -- Operator Interface: PC Front End with Biesse "XP600 + WINDOWS "XP" operating system; 15" color CRT; 40 GB hard drive; full keyboard & mouse; Ethernet connection capabilities. -- Complete with: Universal Auto-Transformer for voltages between 200-600 V, 50/60 HZ; (2) 10 HP, (7.5 kW) BUSCH Vacuum Pumps; safety mats & fencing. -- Actual Model is BIESSE ROVER B 4.40 FT.

2007 Biesse Rover B 7.40 R FTK - 61.22" (routing) - 75" (drilling) - Working field of machine in Z-axis - 5.9" X-axis stroke - 157.87" Y- axis stroke - 77.16" Z-axis stroke - 6.23" 61.22" x 145"

BIESSE ROVER C 6.65 CONF 3 CNC MACHINING CENTER (5-AXIS PROCESSING): -- Specifications: Working Capacity: "X" Axis 253" (6,450 mm); "Y" axis 60.4" (1,535 mm); "Z" axis stroke 25-1/2" (650 mm); max. material thickness 10.8" (275 mm). -- Positioning Speed:"X" & "Y" Axes 328 FPM (100 MPM) each; "Z" axis 98 FPM (30 MPM). -- Worktable:(10) EPS (Electronic Positioning System) Panel supports with: (8) Lifting bars; (4) ATS vacuum pods with universal clamping systems per panel support.(2) Independent working areas with: (10) Pneumatic back stops, (2) pneumatic side stops & (2) pneumatic central stops. -- Boring Unit:4 HP (3 kW) Motor with variable speed from 1,500 - 7,500 RPM; (5) independent vertical spindles in "Y" axis.(4) Horizontal boring spindles with: (1 + 1) in "X" axis & (1 + 1) in "Y" axis. -- Machining:(1) 16 HP (12 kW) Liquid Cooled 5-AXIS electro spindle router with HSK F63 adaptor; variable speed from 3,000 - 24,000 RPM.(1) 33-Position ATC tool rack chain located at the back of the machine. -- Operator & Machine Control:PC Front-End with BIESSE "NC 1000" + "BiesseWORKS" + WINDOWS "XP" Operating System.15" Color CRT, full keyboard, mouse, 1.44 MB & CD ROM disk drives. RS 232 & USB ports.Ethernet connection, specific function controls, & and Internet trouble shooting capabilities.Air-conditioned control cabinet & dust free environment."BiesseWORKS" is a multitask Operating System with: Input/output modules, axes override, (4) axes interpolation, diagnostic graphics aid for programming, machine data & tool management. -- Complete with:(1) 250 m³/Hr Vacuum Pump; safety fences & mats; scrap conveyor; CE mark; original documentation; user & maintenance manuals, wiring diagrams & operation of Numerical Control. -- Actual Model is BIESSE - ROVER C 6.65 CONF 3.

Biesse Rover C 9.65 CNC Router Vacuum Pumps Still under power for inspection

BIESSE ROVER K 1532 CNC MACHINING CENTER (W/ATC & "C" AXIS): -- Specifications:"BRIDGE GANTRY" machine with a working field in "X" axis 126" (3,200 mm), "Y" axis 61" (1,560 mm), max. material thickness 6" (165 mm). -- Positioning speed:"X" Axis 279 FPM (85 MPM), "Y" Axis 196 FPM (60 MPM), "Z" axis 65 FPM (20 MPM). -- Work Table:(8) "ATS" Panels supports with lifting rails for heavy pieces; (4) "ATS" vacuum pods with universal clamping systems on each panel support.BIESSE "Set Up Assist" & digital readouts for pod & rail placement.(2) Independent working areas with (8) pneumatic back stops, (2) pneumatic side stops & (2) pneumatic central stops. -- Boring Unit:4 HP (3 kW) motor with variable speed from 1,500 - 7,500 RPM;"BL 30" Boring head with (20) "Quick Change" independent vertical spindles, (9) spindles in "X" axis & (11) spindles in "Y" axis;(8) Horizontal boring spindles with (2+2) in "X" axis & (2+2) in "Y" axis;(1) "X" axis grooving saw with 120 mm dia. blade. -- Machining:(1) 17 HP (12.6 kW) electro-spindle router with HSK F63 adaptor, variable speed from 3,000 - 24,000 RPM.Motorized dust deflector shield & 6-position adjustable dust suction hood,(1) NC controlled "C" axis for 360° horizontal processing.(1) 16-position ATC tool plate mounted on board the "X" axis at the rear of the machine. -- Operator & Machine Control:PC Front End with Biesse "BH 660" + Biesse "bSolid" + Windows "7 WRT" operating system,15" Flat screen monitor, full standard keyboard & mouse, 1.44MB & CD ROM disk drives for data entry,RS 232 & USB ports, Ethernet connection, specific function controls & internet trouble shooting capabilities.Electronics are mounted in an air conditioning & dust free environment control cabinet. -- Biesse "bSolid" is a 2D/3D Cad/Cam software program that supports the performance of any machining operation thanks to vertical modules designed for specific manufacturing processes.Planning with "bSolid" takes just a few clicks & has endless possibilities; "Real-Time" simulation allows the operator to visualize the piece prior to processing, it provides virtual prototyping of the piece to avoid collisions & ensures optimal machine performance. -- Complete with:(1) 250 m³/Hr Vacuum pump; Hand-held "Remote Control" pendant for immediate operator control; LED bar with (5) colors that show the machine's status in "Real-Time".Safety fences, safety bumpers, safety photocells & safety mats; scrap conveyor; original documentation + user & maintenance manuals, wiring diagrams and operation of Numerical Control. -- Actual Model is BIESSE ROVER K 1532 G VS2

BIESSE - ROVER K 1532: CNC Machining Center (ATC & Boring) -- Specifications:"BRIDGE GANTRY" Machine with: Working field in "X" axis 126" (3,200 mm); "Y" axis 61" (1,560 mm); max. material thickness 6" (165 mm). -- Positioning Speed:"X" Axis 279 FPM (85 MPM); "Y" Axis 196 FPM (60 MPM);"Z" axis 65 FPM (20 MPM). -- Worktable(6) "ATS" Panels supports with: (4) Lifting rails for heavy pieces; (4) "ATS" vacuum pods with universal clamping systems on each panel support.BIESSE "Set Up Assist" & digital readouts for pod & rail placement.(2) Independent working areas with: (6) Pneumatic back & center stops; (4) pneumatic side stops; (2) LH & (2) R. with (12) removable nylon clamping units for narrow pieces. -- Boring Unit:4 HP (3 kW) Motor with: Variable speed from: 2,800 - 6,000 RPM."BL 30" Boring head with: (20) "Quick Change" independent vertical spindles; (9) spindles in "X" axis; (11) spindles in "Y" axis.(8) Horizontal boring spindles with: (2 + 2) in "X"'; (2 + 2) in "Y" axis.(2) Grooving Saws: (1) In "X" axis; (1) in "Y" axis for max. 120 mm dia. blade. -- Machining(1) 17.7 HP (13.2 kW) Electrospindle router with: HSK F63 Adaptor; variable speed from 1,000 - 24,000 RPM.Motorized dust deflector shield with: 6-Position adjustable dust suction hood; blowing unit.NOTE: NC Controlled C-Axis for 360° horizontal processing is not installed but CAN BE ADDED. - Per spec sheet on Dropbox folder: "“Prearrangement for the assembly of a 360° operating unit (C axis). It includes all the harness for the electric cabinet. The slot is to be specified. It allows reducing machine downtime for the installation of this unit on an already delivered machine";. (1) 16-Position ATC tool plate mounted on board the "X" axis at the "X" axis carriage (rear of the machine base). -- Operator Interface:PC Front-End with: BIESSE "BH 660" + BIESSE "bSolid" + Windows "7 WRT" Operating System.21-1/2" Flat screen monitor; full standard keyboard & mouse; 8 GB RAM memory;128 SSD GB hard disk or superior; USB Ports for data entry. Dedicated graphics card; Ethernet connection to an office PC with specific function controls & internet trouble shooting capabilities.Electronics are mounted in an air conditioned & dust free environment control cabinet. -- BIESSE "bSolid" is a 2D/3D CAD/CAM software program that supports the performance of any machining operation thanks to vertical modules designed for specific manufacturing processes.Planning with "bSolid" takes just a few clicks & has endless possibilities; "Real-Time" simulation allows the Operator to visualize the piece prior to processing; it provides virtual prototyping of the piece to avoid collisions & ensures optimal machine performance. -- Complete with:(1) 100 cbm/Hr Vacuum Pump; handheld "Remote Control" pendant for immediate Operator control; LED bar with (5) colors that show the machine's status in "Real-Time".Centralized Automatic Lubrication System; Scrap Belt conveyor; Tool Per-setting device; Safety fences; s

BIESSE ROVER K 1531 FT FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications: 5' x 10' "Bridge Gantry" machine with "Phenolic Matrix Grid" table. -- Working Capacity: "X" Axis 122" (3,100 mm), "Y" axis 61.4" (1,560 mm), "Z" axis stroke is 12.5" (320 mm), max. material thickness 6.69" (170 mm). -- Positioning Speed:"X" & "Y" axis 196 FPM (60 MPM), "Z" axis 82 FPM (25 MPM); Vectorial High Speed 278.4 FPM (82 MPM).?"X" & "Y" axes use a precision rack & pinion system, "Z" axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital brushless AC Servo motors.All motion components are maintained by a lubrication system. -- Work Area:Flat table design with "Phenolic Matrix Grid" worktable that allows for automatic locking using T slots or possible vacuum locking (requires a vacuum pump). The machine has 1 working area with 2 left + 1 front & 1 rear origins, (2) reference pin stops for rear LH area, (3) reference pin stops for front LH area &(2) reference pin for side stops (LH side) -- Boring Unit:"BH 10" boring head, (1) 2.5 HP (1.7 kW) - 2,800 - 6,000 RPM variable speed motor; (5) independent vertical spindles in "X" axis & (5) independent Vertical spindles in "Y" axis. -- Machining:(1) 12 HP (9 kW) Air cooled "HSD" Electro-spindle with HSK F63 adaptor, variable speed from 1,000 - 24,000 RPM.(1) 10-Position ATC tool rack mounted on the end of the machine; NC controlled digital presetting device for the measurement of the tool length. -- Operator Interface:PC Front End with: Biesse "BH 660" + "BiesseWorks" + WINDOWS "WRT" (Windows Real Time) operating system;Intel Core I7 CPU, 8 GB RAM memory, 128 SSD GB hard disk, Dedicated graphic card, DVD burner, USB ports.21.5" LCD Flat screen monitor; full keyboard & mouse all mounted on a mobile cart; Ethernet connection capabilities.BiesseWorks graphic interface with assisted graphic editor used to program machining operations; parametric programming and guided creation of parametric macros Import of CAD and other external software files in DXF and CID3 format; 3D simulation of the tool path, calculation of machining time & the ability to create rotate virtual faces. -- Complete with:(2) "Becker H360/1428" 300 m³/Hr vacuum pumps, Automatic program update according to the tool length touch-off probe. Automatic Lubrication system for linear guides, pads and re-circulating ball screw. Universal Auto-Transformer for voltages between 200-600 V, 50/60 Hz. Hand-held control Pendent.NCE safety system for stand-alone machine with 3 sides access with 4 sides light barriers & Anti-climb over extension on the right side of the base-frame -- Actual Model is BIESSE ROVER K 1531 FT

BIESSE AKRON 435 EDGEBANDER WITH CORNER ROUNDING0.4 - 3 mm Banding capacity, 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5.5") minimum panel length, and 85 mm (3.3") minimum panel width.Equipped with: -- Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machined. -- Quick change glue pot system. -- (1) Large 150 mm dia. driven & (5) idle pressure rollers. Edge Feeding and Pressing Unit VC-511 - Automatic loading of tape in rolls and strips. -- Feed Speeds: 33 - 46 - 65 FPM.Workstations: -- Double Motor End Trim, tiltable from 0° - 15°, each motor 0.8 kW (1 HP) - 12,000 RPM. -- Top and Bottom Trimming Unit with (2) motors 0.65 KW (0.87 HP) each - "Pronesting" copiers - Cutters R-2 mm: -- Corner Rounding Unit with (2) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors. -- Top and bottom radius scraping. -- Top & Bottom Flat Glue Scrapper. -- Top & Bottom Oscillating Buffing Station, (2) motors, each 0.5 HP - 2,800 RPM.Operator & Machine Control: -- Operator control panel, High Definition touch screen control Windows XP based. User-friendly graphic user interface with diagnostic and assisted maintenance. -- USB end Ethernet port. Controller (max. of 320 programs), soft-touch keypad & 6" color LCD screen, displays in millimeter or inch units, automatic or manual startup.Complete with: -- All cutting & trimming workstations are HF (high-frequency motors 200 HZ) and enclosed by padded sound enclosure. -- Top pressure is provided by staggered double-row hold-down wheels mounted on ball bearings.NOTE: Return conveyor not included

Biesse Akron 440 Edgebander Premill Top & Bottom Trim Corner Round Edge Scrape Glue Scrape Buffing Unit 12-18 m/min Feed Speed All work units are servo controlled

BIESSE AKRON 440 AX EDGEBANDER (W/PRE-MILL & CORNER ROUNDING: -- Specifications: Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood. -- Edge & Workpiece Capacity: 0.4 - 3 mm (0.016 - 0.12") Edge; 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5-1/2") min. panel length, and 85 mm (3.3") min. width. -- Working Units:Pre-milling Station: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blow off device and SIKO digital counters for adjustments. -- EVA Gluing Unit: Edge Feeding & Pressing Unit; automatic loading of tape in rolls and strips; quick-change glue pot system. -- Pressure Section: (1) Large 150 mm dia. driven & (5) idle pressure rollers. -- Feed Speeds: Operating feed speeds 12 & 18 MPM (39 & 60 FPM). -- Workstations: Double Motor End Trim; tiltable from 0° - 15°; each motor 0.8 kW (1 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Trimming: (2) Motors 0.65 kW (0.87 HP) each; "Pro-Nesting" copiers; cutters R=2 mm. -- Fine Trim/Corner Rounding Unit: (2) Motors; each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material, and wood edge banding up to 3 mm max. edge thickness. -- Top & Bottom Flat Glue Scrapper: To remove potential glue squeeze out. -- Buffing Station: Top & Bottom, (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Operator Interface:Operator Control Panel, "HDI" High-Definition touchscreen control, Windows XP based. -- User-friendly graphic user interface with diagnostic and assisted maintenance. -- USB and Ethernet port; 1.44 MB floppy drive, automatic or manual startup. -- Complete with:High frequency motors (200 HZ): Padded sound enclosure. -- Top pressure beam with staggered double-row hold-down wheels mounted on ball bearings. -- Actual Model is: BIESSE AKRON 440 AX

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).

BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback"; of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Work stations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).

BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm Material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback"; of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Workstations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).