Veneer Equipment For Sale
Category
Veneer Equipment
39 Results Found
ADOLF JOHN & COMPANY Model "FS IV" Automatic Guillotine;Specifications: -- 126" Max. length cap., 3-7/8" cutting height. -- 0.5 HP motorized parallel fence, adjustable from 1" - 64", push-button controlled travel with digital readout, micro-adjustment by hand wheel. -- 7" Wide hydraulic pressure beam with rack & pinion travel; 5.5 HP gear pump motor for pressure beam and knife cutting operation, approx. (2) Sec cycle time/cut; -- Complete with: (2) Palm buttons for safety.All Hydraulics were reconditioned in 2013, and Guillotine has been used very little since.
Call for Price
The seller has confirmed that these (2) Amitec VT veneer slicers are in good working/running condition. They are ready to load! - (2) Available - Slices log cants in the lengthwise direction - Compares to the Marunaka SL-250 - 9-7/8" (250mm) Max lumber slicing width: With up to 9-7/8" high cant, veneer thickness 1/25" to 3/8". 75° knife angle with 18 ° knife bevel - Knife length: 46-1/2" (1,180mm) - Motorized upper feed beam with Continuous belt feed - Variable speed: 120-180FPM (40-60 m/min) - 30HP feed motor - Head elevator: 1HP - Approximate weight: 16,000 lbs - 327"L x 62"W x 75"H
ANGELO CREMONA TZE 4000 4 m up-stroke Veneer Slicer with flitch pushers and MERRITT vacuum table. -- Now offered at a greatly reduced price!
Call for Price
$138,500
CAPITAL Half-Round Slicer with a 125 inch length capacity and the following additional features: -- 50 HP Drive. -- Removed from service and Checked. -- Includes loading onto Buyer's truck.
$193,500
CAPITAL Half-Round Slicer with a 150 inch length capacity and the following additional features: -- 50 HP Drive. -- Includes CAPITAL Knife Grinder at no additional charge. -- Fully Reconditioned to "like new"! -- This machine was reconditioned at the factory yielding a slicer value of around $300,000. Somebody went out of business and you get a real bargain price!
$149,500
CAPITAL Slicer with a 165 inch length capacity and the following additional features: -- 50 HP Main Drive. -- Still in-place connected to power for test operation but cannot be seen running a log. -- Includes loading onto Buyer's truck.
Call for Price
CAPITAL 36" Veneer Clipper. --36" Length of cut capacity, double-rod mechanical clutch driven by 3 HP motor, foot pedal actuation of cycle. -- Speed: About 90 cycles per minute max., shear cut angle with scissor-like angle mounted knife, motor mounted inside frame & V-belted to flywheel. --Includes: Re-sharpened knife, standard integral infeed support table and double rod guards.
Call for Price
CAPITAL 125" Veneer Clipper. --125" Cap., straight knife cut for end grain clipping; 3 HP motor. -- Two-hand safety controls; Max. (90) cycles/Min. -- Complete with safety guards. -- Completely reconditioned; with new knife and shear plate.
Call for Price
CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- 10' COE Knife Grinder. -- Steel Framework and 450 FPM plus uniwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was actually regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.
Call for Price
CASATI MACCHINER 3600 Double Knife Guillotine. -- Overall data: Cutting length 3,600 mm (141.7"), cutting width between knives from 18 mm (3/4") to 530 mm (20.8"), max. cutting thickness 100 mm (3.9"). -- Drives: Motorized rear fence width adjustment w/digital display; manual & automatic working cycle with electronic sensors that measure the veneer pack width; hydraulically powered & controlled speed, pressure & knife operation. 18 HP hydraulic pump motor -- Controls: Micro-processor for programming & storing up to (99) cutting sizes, 5" screen, alpha numeric keypad for dimensions input; complete with "optimization" software & electronic fault diagnostic system. -- Complete with: Thin green edge light beam for front knife cutting line and first knife set up for single cuts; automatic centralized lubrication, safety photocells and manual. -- Feature: When in single knife cutting mode the front blade cuts over 12' length. -- Includes: Extra blades - needs sharpening. -- Work required prior to shipping: Machine pictured from prior owners premises. It will be fully gone over, replace the cutting matts and knives sharpened. Painted if requested.
Call for Price
COE 249D Veneer Lathe with the following: -- 27" maximum log diameter, 110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling 35 cubic meters per hour. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in excellent condition.
Call for Price
COE 4 Ft. Veneer Peeling Line with the following major components and features: -- Log cut-off saw. -- Geometric lathe charger. -- Dual spindle 4' COE Model 263 Lathe: ● Diameter of outer spindle 7" ● Diameter of inner spindle 4" ● Max. swing 48" ● Knife length 56" ● Lloyd controls including motor starters ● Main drive DC-AC 165 HP/200 HP -- Veneer conveyor to clipper. -- Pneumatic Clipper.ALSO AVAILABLE: VENTEK Veneer Scanner (no computer included).NOTE: Veneer stackers not included.
Call for Price
COE Model M62, Veneer Roller Jet Dryer fully complete with the following major components and features: -- Veneer Feeder and Unloader, -- 4-Decks, -- 16-Sections, -- Steam heated, -- Half of the Jet Nozzle Boxes have been changed to the M72 style.
Call for Price
CREMONA TM 3600 Veneer Clipper. -- Capacity: 3,680 mm (145") Cutting length cap. and 3" max. cutting height, heavy duty welded steel construction, precision cutting clipper. Heavy duty knife beam with 5 HP self-braking, hydraulic drive for intermittent or continuous operation. Knife beam with vertical oscillation movement for a progressive scissor cutting action. 3-Position adjustable rear table. -- Includes: Foot pedal control, PLC electrical, and installed knife.
Call for Price
$21,480
DIEHL VS-81 Tapeless Veneer Splicer; -- Specifications: 1.5 HP TEFC variable speed feed motor, 15 - 85 FPM feed speed; handles stock from 1/64" thick and 6" min. length up to 42" wide. -- Equipped with: 4-Roll infeed matching roll assembly, thermostatic controls for upper-and-lower heater bars (200° - 500° F temperature range). -- Complete with: Automatic oil mist lubrication; outfeed with powered take away roll for veneer, start/stop push buttons for feed motor, and overload & under voltage protection. This machine has been fully rebuilt and comes with a full one (1) year warranty on all parts.
Call for Price
DIEHL VS 81 Tapeless Veneer Splicer for Regular and Thick Veneer; For stock material from 1/64" to 1/4" thick and 6" min. length - special upgrades to process "thin or thick" veneer with Thick Veneer Package.Specifications: -- 1.5 HP TEFC variable speed feed motor 15 - 85 FPM with digital feed speed indicator.Added Variable Speed Drive (VFD) -- Handles stock from 1/64" to 1/4" thick and 6" min. length, 42" max. width to the right. -- 4-Roll infeed matching roll assembly.Special Feature: With Thick Veneer Package with special internal parts in the head that include springs, shoe bolts, shoes, and fish-back parts (see photos). Plastic chain is better for thick veneer to reduce the highly increased friction that occurs when more downward pressure is needed (by operator via hand wheel) for the thick veneer. Package also includes VFD added to easily reduce speed on thick veneer.Features: -- Overhead holddowns to insure veneer flatness; digital thermostatic controls for upper & lower heater bars (200° - 500°F) total 9,000 watts; -- Lower driven brand new plastic chains to elliminate blue stain. -- Start/stop push buttons for feed motor, overload and under voltage protection. Reconditioning includes plastic top feed chains. Machine warranty for 1-year.
DIEHL VS 81 Tapeless Veneer Splicer; Handles stock from 1/64" thick & 6" min. length up to 42" wide, 14 - 75 stitches/Min.Specifications: -- 1.5 HP Variable speed feed motor, 15 - 85 FPM, 42" throat, 100" x 75" table. -- Manual raise and lower temperature controls (200 - 500°) for heater bars. -- This machine was overhauled in 2012, and is ready for your production needs.
There are (4) machines at this facility. Two are used in production and the other two are in storage. 87" Capacity