Woodworking Equipment For Sale

BOERE - TK 1300, ...Abrasive Planer -- (1) Head, 51" width cap. x 6" thickness cap.; 10" dia. spiral rubber-covered contact drum, 50 HP motor. -- Abrasive belt size 52" x 75", air tensioning, and BO-TRACK electronic abrasive belt tracking. -- 2 HP Variable feed speed motor for 16 - 82 FPM. -- Single infeed rubber-covered holddown roll, followed by floating shoe on the infeed, and single outfeed rubber covered holddown roller followed by rotating cleaning brush. Complete with: -- Motor load meter, (4) corner mounted screw jacks with powered bed raise & lower, and 9-3/4" dust port.

50” width drum/drum/platen heads 480 volt 3-phase Bottom and top sanders can be sold separately Pictures coming for bottom sander

Brandt KDF 440C Edgebander

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

BRANDT AMBITION 1120 FC (aka KDF 120 C) (EDGEBANDER WPRE-MILL & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity, 0.4 - 3 mm Edge cap., min. panel thickness 8 mm (0.3"), max. panel thickness 40 mm (1.57"), min. panel width 70 mm (2.75"). Min panel length: 140 mm (5.5")Line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all workstations. Auto in-feed stop to insure proper spacing between panels. Equipped with: -- Pre-Milling Station:(2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Gluing Section:Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, Pressure Section with (1) large drive plus (2) idle rollers "pneumatically controlled." Hot Melt granulate quick heat-up glue system. Workstations: -- End Trimming: 2 x 0.18 kW (1/4 HP), 12,000 RPM motors, THK guided, chamfers 0° - 15°. -- Flush/Bevel/Radius Trimming:2 x 0.55 kW (0.75 HP),12,000 RPM motors with insert knives for 3 mm PVC radius. cutter-heads, bevels 0° - 15°. -- Corner Rounding Station:1-Motor (4-corners) contour trim for profile corner rounding, 1 x 0.35 kW (0.5 HP), 12,000 RPM motor, with insert knivesFor 3 mm PVC radius w/digital read-out set-up and pneumatic change-over from thin to thick PVC edge tape. -- "Quick-Change" Profile Scraping Unit:Top & bottom for 2 - 3 mm radius, pneumatically controlled blow-off nozzles. -- Flat Scraping Unit:Top & bottom flat scraping units with copy wheels to remove residual glue squeeze-out. -- Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Complete With: &#9679 Trim stations have HF motors w/electronic brakes &#9679 Fixed feed chain track speed of 8 MPM (26 FPM) &#9679 2 HP feed drive &#9679 208/230/440/480v, 3ph Transformer &#9679Sound/Safety Enclosure &#9679 Adjustable Out-Rigger Support &#9679 Used tooling. -- Actual Model is BRANDT AMBITION 1120 FC (aka KDF 120 C)

BRANDT AMBITION 1200 (aka KDN-200) EDGEBANDER (Compact): -- Specifications: 0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length. -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive rollWorkstations: -- Vertical travel double-motor front & rear end trim with tilting of 0° - 15° cap. (0.24 HP - 12,000 RPM motors); -- Top & Bottom Multifunctional Trimming Units (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors).Equipped with: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on hold-down beam. -- Electronic motor brakes on trimmers. -- Feed speed of 30 FPM.Includes: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual. -- Actual Model is BRANDT AMBITION 1200 (aka KDN 200).

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT AMBITION 1440 FC (KDF-440 FC) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Heated Adjustable Infeed Fence: Radiant Heated with Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for Top & Bottom, Leading & Trailing edges & Corner Rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 FC (KDF 440 FC).

BRANDT AMBITION 1650 FC HIGH FLEX EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): Specifications: -- Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units.Equipped with: -- 3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High-Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 KW, 3 KG (6.61 Lbs.) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- QA 45 Quick-change glue tank with electronic switchable/emptying mode for easy maintenance & glue color change.Melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Adjustable glue amount with servomotorPressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electropneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") ma

BRANDT AMBITION 1650 FC High Flex EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications: Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Equipped with:3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 KW, 3 KG (6.61 Lbs.) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- Quick-change glue tank for easy maintenance & glue color change, melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electropneumatic reset for straight or chamfer trimming. -- Top & Bottom Multistage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (2) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different radius profiles, pneumatic (2) position indexing for different edge thickness.

BRANDT KDF 110 (AMBITION 1110) Edgebander with Pre-Mill0.4 - 3 mm (1/8") Edge thickness cap., 8 - 40 mm (0.3" - 1.57") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- In-Feed Fence, adjustable, manual with digital indicator. -- Pre-Milling Unit, (2) motor, (1) jump, counter-rotating for the best possible glue joint. -- Gluing System, hot-melt, quick heat-up time and easy maintenance. -- Edge Magazine, automatic for strip & coil stock, 3 mm PVC guillotine, -- Side Pressure Section, (1) driven plus 2-idle roller w/digital readout setting.Workstations: -- End Trimming Unit, double motor end trim (2 x 0.5 HP - 12,000 RPM motors), chamfers 0° - 15°. -- Multi Trimming Unit, top/bottom for flush/bevel/radius trimming with (3) quick setting positions. Motors (2 x 0.5 HP - 12,000 RPM) with insert knives. -- Buffing Unit, top/bottom (2 x 0.5 HP) motors. -- NOTE: Open station at end; scraping unit could be addedControls:LCD Display, approx. 2 x 6" with soft-keys for fast navigation and operator comfort. Complete With: -- Feed Speed, fixed 8 m/Min (26 FPM), 3 HP feed drive. Sound enclosure and Scraper collection box.Actual Model: AMBITION 1110

Brandt Ambition 1110 Edgebander

BRANDT AMBITION 1680 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) -- Specifications: Edge thickness: 0.4 - 12 mm (0.02" - 1/2"); incl. 3 mm (0.12") PVC banding. -- Workpiece: Thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width: 70 mm (2.76"); min. workpiece length: 160 mm (6.37"). -- Working height: 950 mm (37.8"). Equipped with: -- 3 HP (2.2 kW) Feed motor; variable feed speeds from 26 - 59 FPM (8 - 18 MPM); applying solid or using corner rounding units. -- Heated Infeed Fence. -- Infeed panel support with: Roller guide extends out to 800 mm (31.4"). -- Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") Wide Heavy-Duty feed chain with: Rubber pads, automatic chain track lubrication. -- Top pressure section with: Double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency motors); line control (no limit switches) for workstation functions. -- Top & Bottom spraying device: Located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") height. -- Centralized Lubrication system.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads; electro pneumatic jump control on 1st motor; electronic frequency inverter for control of motor speed & braking; SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 kW, 3 kG (6.61 Lbs.) cap.; glue viscosities: 25,000 - 80,000 mPa; temperature range: 120° - 245° C (248° - 473° F); max. melting capacity 6 kG/Hr.EVA Hot Melt Glue Application System: -- Quick change glue tank with Premelter for easy maintenance & glue color change; melting capacity: Approx. 6 - 10 kG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electro-pneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different ra

BRANDT AMBITION 1870 (aka KDF 870) EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING); -- Specifications: Edge & Workpiece Capacity, 0.4 - 20 mm Edge thickness cap., incl. 3 mm PVC banding, min. workpiece width 65 mm (2.5") and min. length 160 mm (6.375"), panel thickness 8 - 60 mm (0.314" - 2.187".3 HP (2.2 KW) feed drive for variable feed speed 36 - 65 FPM (11 - 20 MPM), with CR engaged or applying solid wood up to 52 FPM (16 MPM) max feed speed.infeed panel support w/roller guide extends out to 1,000 mm (39").Working height 900 mm (35"); 80 mm wide Heavy Duty feed chain w/rubber pads, motorized raise/lower upper pressure beam.Automatic chain track lubrication; top pressure section with non-marking neoprene pressure wheelsAll cutting & trimming workstations are HF (High Frequency Motors); Line control (no limit switches) for workstation functions. Equipped with: -- Pre-Milling Station: (2) 3 HP (2.2 kW) - 12,000 RPM "HOMAG" Vertical milling/jointing heads, electro-pneumatic jump control, heads counter-rotate, SIKO digital units for vertical & horizontal adjustments. -- "Quick-Melt" Hot Melt glue system w/pre-melting hopper feed, "quick change" hopper & tank for color changes, reversible glue applicator roller rotation; approx. (12) Min heat-up time. -- Extended Magazine for application of solid edges from 0.4 - 20 mm (3/4") thickness and coil material from 0.4 - 3 mm thickness; Infrared heating unit positioned between glue roller and pressure zone to improved edge quality. -- Program controlled motorized pressure zone: Pressure section with (1) large driven and (4) pneumatically controlled idle rollers, SIKO digitals for setting. Reinforced guillotine for coiled edgebanding material 0.4 - 3.5 mm thickness and 8 - 55 mm height; -- Brandt "Power Control PC 20+" with 12' TFT flat screen monitor; front side USB port, 1 GB Flash Card, 600 MHZ Hard Drive, 256 MB RAM; Internal modem for remote diagnostic link.Edgebander Workstations: -- Front & Rear End Trim: (high speed version, 1 HP - 12,000 RPM ea.), pneumatic control for straight or chamfer-trimming. -- Servo controlled Top & Bottom Rough Trims: (2 HP - 12,000 RPM motor ea.) w/vertical & horizontal tracing, pneumatic (in/out position) control from control panel, tilts 0 - 25°. -- Top & Bottom Fine Trimmers: (1 HP - 12,000 RPM motor ea.), Servo control bevel 0° - 25° tilt angle, w/vertical & horizontal tracing, Servo Control (in/out position) from control panel; contour profile trimming units (two 0.5 HP - 12,000 RPM motors), Servo Control (in/out position) from control panel (all trim station motors are 200 Cy HF and equipped w/electronic brakes). -- Corner Rounding Unit: (2) Motors (0.5 HP / 0.4 kW) - 12,000 RPM motors ea, 16 MPM (52 FPM) operating feed speed. -- Quick Change Top & Bottom Profile Scraping Unit: With digital "quick-set" system for 2 - 6 mm radius (0.078" to 0.47"), Servo Control in/out from operator panel and pneumatically controlled blow-off nozzles. -- Top & Bottom Buffing u

BRANDT - KDF 660, ...Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

BRANDT KDF 660 2C EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications:Work-Capacity 0.4 - 8 mm Edge cap; 8 - 55 mm Panel thickness; 160 mm (6-3/8") min. panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Feed-Speed 14 MPM (11 MPM automatically when corner rounding). Equipped With: -- Pre-Milling Station, for cleaning edges of panel. -- Quick Change Gluing System, for maintenance & glue color change. -- Automatic Magazine for strip & coil stock, 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" & Servo controlled pressure sections for quick edge thickness changeover. Workstations -- End Trimming: Double motor (2 x 0.5 HP - 12,000 RPM motors), automatic chamfer from control panel 0ø - 15ø. -- Pre-Flush Trimming: Top & bottom (2 x 0.5 kW approx. or 0.67 HP - 12,000 RPM motor) with (4) pre-set position index settings. -- Fine/Bevel/Radius Trimming Station: Top & Bottom (2 x 0.35 kW approx. or 0.50 HP - 12,000 RPM) bevels 0ø - 25ø, with combination flush/radius/chamfer cutter heads; horizontal & vertical tracing wheels, comes with optional brushless Servo motors for quick thickness changeover. -- Corner Rounding Station: (2 x 0.35 kW motors or 0.5 HP - 12,000 RPM motors) for leading & trailing edges of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Profile Scraping Unit: Top & bottom PVC radius scraping with pneumatic control, PVC Scrape collection box. -- Flat Glue Scraping Unit: Top & bottom glue-joint scrape station. -- Buffing Unit: Top & bottom (2 x 0.125 HP - 1,400 RPM motors).Complete With:&#9679 Operator Control Panel, Power Control PC 20+ with color LCD screen & soft keypad. &#9679 All trimming stations have HF motors w/electronic brakes. &#9679 Padded sound enclosure and used tooling. -- 220/480v, 3Ph, 60Hz transformer. -- Actual Model is BRANDT KDF 660 2C

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.