Woodworking Equipment For Sale

BALESTRINI C 70 Double Sided Feed Through Copy Shaper;Profiles various chair, table and casegood components from a prepared template. The feed through system allows curved or extremely long parts to be shaped with little or no limitation. Equipped with: -- (2) Vertical shaper spindles, 7.5 HP motor each; 30 mm dia. spindles, 8,000 RPM cutter rotation. -- Reversing rotation by switch for climb cut or conventional cut. Specifications: -- Max. working width 358 mm (14-1/8"), max. working height 118 mm (4-5/8"), min. working length 240 mm (9-1/2"); max. size of cutter blocks 90 mm x 120 mm and up to 3/8" vertical adjustment of heads. -- Part on template block is being shaped by running between spring loaded spindles with copy bearings following the template pattern. -- 1 HP variable feed motor 3 - 26 FPM, hand crank adjustable horizontal rubber infeed & outfeed holddown rollers. -- Machine has (2) 120 mm diameter dust outlets. -- Machine dimensions: 53" x 49" x 43" Machine weight: 2,310 lbs.

BALESTRINI MINI C 2500 DOUBLE SIDED TEMPLATE PROFILE SHAPERSpecifications: -- (2) Offset shaping heads with 10 HP (7.5 kW), 230/460 volt three phase drives. (1 each side) -- Maximum reciprocating length 98" (2500 mm). -- Maximum height 7" (180 mm). -- Maximum width between spindles 8", and shaping heads are staggered for full end rounding. -- 1¼” Diameter work arbors with 7″ under the nut capacity, and Spindle speed of 8400 RPM -- Hydraulic stroke of 9-3/4″ wide x 110″ long tee slotted work table, with feed speeds of 3 - 49 feet per minute (1-15 m/Min.) powered by 3 HP, 230/460 volt three phase hydraulic pump -- Overhead beam clamp bar with (4) adjustable clamps. -- Push button operator control station.

Barberan UV Oven

Barr Mullin Wondersaw Optimizer with Computerized Laser Controls Tichniess: Up to 3" Width: 31" Min cut: 4" Feed height: 34-1/2" Floor Space: Apprx 21' x 15' 480 volt

Baxter Whitney "No. 32A" Planer - 30" Machine is in full working order. We will provide services for power disconnect as well as loading onto any transport vehicle provided.

SALE PENDING Baxter Whitney "No. 32A" Planer - 30" Machine is in full working order. We will provide services for power disconnect as well as loading onto any transport vehicle provided.- Call 800-459-2148 for more info.

Baxter Whitney & Sons Planer model 32-A manufactured in mid 1940s. This planer was taken out of service in good working order about 8 years ago. I have not used it. There is one pulley that has a broken edge as seen in photo 9319. This was broken in transit and should not affect its function . This planer has a 15 hp, 3 ph main motor with a 3 hp feed motor. Dust hood included. It will need to be picked up with a roll body truck. It comes with the knife sharpener and the sharpener box. Call 800-459-2148 for more info.

BCAM 530E CNC Router with Infeed & Outfeed System

BECKER VTLF 2.400 Vacuum pump:Seller states the pump was only turned on a few times15 HP Oil-less (Dry) Rotary Vane vacuum pump system, rated @ 270 CFM open flow, max. 23.6" Hg; heavy duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance free with built-in carbon vanes and built-in suction filters. Complete with: Vacuum regulating valve, secondary suction for additional cooling, blow-off valve/silencer, 4" BSP x 4" NPT Nipple; coupled to a 886 RPM TEFC motor.

Becker VTLF 250 Vacuum Pump: 6.6 kW (8.8 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, 176 CFM, max. 25"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; 2-1/2" BSP x 2" NPT nipple coupled to a TFC; 1,150 RPM motor. -- Also available at extra cost! -- $2,800 for the ROW 25 HP phase converter -- $1,900 for the electrical control panels

Becker VTLF 250 Vacuum Pump: 7.5 kW (10 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, 176 CFM, max. 25"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; 2-1/2" BSP x 2" NPT nipple coupled to a TEFC; 400/480V, 1,160 RPM motor

BECKER KVT 3.100 3.6 Kw (5 HP) Vacuum pump:Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 69 CFM and 100 cm/Hr with max. 27"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blowoff valve/silencer. -- Complete WithInlet vacuum air filter system.

Bertheson Press Platform size 51 Wide X 102 Long with 2 16 ft shuttle driven aluminum runner platforms. Pressure 2500 psi and we ran a temperature of 350 degrees for Tego and 165 degrees for plywood. The Press can laminate Tego Film glue or pva c glue. This press is a double shuttle and can laminate up to 14 ft by double pressing on shuttle. We can get the press operational if you are interested. We only have to hook up the power. Very good condition!

Biesse Rover B Edge semi automatic pod setting 4 coil magazine vertical and horizontal drill bank main spindle with U axis Milling X1: 5055 mm Y1: 1600 mm Edgebanding X2: 4100 mm Y2: 1600 mm Milling Module H74 - Z1: 245 mm Module H29 - Z2: 290 mm

2007 Biesse Rover B 7.40 R FTK - 61.22" (routing) - 75" (drilling) - Working field of machine in Z-axis - 5.9" X-axis stroke - 157.87" Y- axis stroke - 77.16" Z-axis stroke - 6.23" 61.22" x 145"

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

Biesse Elix K3

Biesse Akron 1440 PUR Return conveyor available - demo unit!

Biesse Cosmo Case Clamp Bought new, never used

BIESSE - AKRON 855, ...Computer Controlled Production Edgebander.Features & Main Specifications: -- Computer-controlled interface for workstations with: Servos and pneumatic positioning devices. -- Programmable selections for "1-touch" changeover between edgebanding types and thicknesses. -- Edgebanding thickness: 0.4 - 19 mm Capacity. -- Min. panel: Width 85 mm & length 140 mm; thickness of 10 - 50 mm. -- Feed speed variable from 10 - 20 MPM, 3 HP feed drive.Frontend Equipped with: -- Premilling Unit with: (4) Positions for automatic changeover between premill settings, NC controlled. -- Strip & Coil Edge magazine: Automatic, "HD" shear-type guillotine. -- Top Pressure Beam: On-screen adjustable for height positioning. -- Hot-Melt Glue System: 12 Min heat up time, Teflon® coated gluepot; digital thermostats with automatic kick-down when machine is in idle mode. -- Side Pressure Section with: (1) Large dia. "non-stick" coated drive roller; (5) Teflon® plated idle rollers with Servo positioning, and NC controlled material thickness adjustment. Workstations: -- End Trimming Unit: Front & Rear (0.33 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 15° on horizontal. plane, NC controlled. -- Flush Trimming Unit: Top & Bottom with "Quick Change" motors, 1.0 HP - 12,000 RPM motors; digital readouts for easy setup. - 2-Position NC controlled. -- Flush/Bevel/Radius Trimming Unit: Multiuse top & bottom, 2-motor (0.3 HP - 12,000 RPM). Servo driven positioning of motors for different edge trimming setups. NC Controlled adjustment between profiles and positions. -- Corner Rounding Unit: 4-Motor (0.3 HP - 12,000 RPM motors) for trimming leading & trailing upper & lower edge/corners with "Fast Position"; can be used as a 2nd Top & Bottom fine trimmer, as well. -- Profile Scraping Unit: Top & Bottom for 2 mm or 3 mm thick PVC banding; digitals for horiz. adjustments. -- Flat Scraping Unit: Top & Bottom for glue and fine panel scraping. -- Buffing Unit: Top & Bottom (0.5 HP - 2,800 RPM motors), units tilt 0° - 30°. -- Hot Air Blower Unit: Top & Bottom edge reactivation station (2,000 Watt), hot air blowers with temperature adjustment. Complete with: -- Programmable processor for workstations & feed speed. -- Insulated sound enclosure over all trim stations with: Triple split dust & safety hood enclosure, industrial lights, and viewing windows. -- Extendable side panel support rail. -- 12 KVA - 240 Hz Digital frequency inverters.Includes: -- Used tooling on all workstations. -- Extra set of diamond tooling for premill unit. -- (1) Premill motor. -- NOTE: Chain pads have been replaced (2) years ago