Northfield For Sale

Oliver 36" Band Resaw

OLIVER 6910 Oscillating Spindle SanderPedestal style Spindle Sander constructed for rugged use .Specifications: -- 2 HP Motor drives and is connected through a flexible coupling, and can be installed or removed without disturbing the drive mechanism. -- Spindle speed 1,725 RPM, Oscillation speed 75 Cy/Min with 1-1/2" stroke length. -- Spindle quill runs in precision ball bearings, oscillated by a heavy duty worm & gear mechanism running in a bath of oil. -- (10) Spindle sizes provided: 1/4 x 5", 3/8 x 6", 1/2 x 6", 5/8 x 6", 3/4 x 9", 1 x 9", 1 1/2 x 9", 2 x 9", 3 x 9" and 4 x 9"; 100 grit abrasive sanding sleeve with each spindle. -- Large 24" x 24" precision ground cast iron table mounted on large trunnions that can be tilted 45° down and 30° up by use of a convenient handwheel. -- Complete with: Pedestal style stand.

OLIVER 4045 12" PROFESSIONAL TABLE SAW, with 36" FenceHeavy-duty cast iron table precision ground for accuracy; rugged machine frame construction provides maximum stability and reduced vibration.Specifications: -- 12" Blade capacity and 0° - 45° tilting arbor with digital read-out. -- 7.5 HP Motor at 3,450 RPM. -- Complete with: 52" rip fence capacity that will handle most of your work. -- 48" x 52" Cast iron table. -- Blade guard, miter gauge, push-button controls. -- Parts list & operation manual.

OLIVER 4016 10" Table Saw, 5 HP, 3-Ph w/36" Rail Specifications: -- 5 HP motor; poly V-belt drive system with belts that run smoother and with less vibration, giving you the highest quality cut available. -- Top it all off with with OLIVER'S Optimus square tube fence and a digital blade angle readout system and you've got a saw that tears it up with accuracy and in style! -- Model 4016.004 5 HP, 220V. 3-Phase.

OLIVER 5385 Single Head Wide Belt SANDER (37") 1-Head and 37" belt width Combination Sanding Head with rubber covered contact roll and adjustable finishing platen, 1/8" - 5" Thickness capacity, 36" width capacity.Specifications: -- 20 HP Main drive motor. -- 1 HP Variable speed (15 to 45 FPM). -- 1/4 HP Power raising and lowering conveyor bed motor. -- 37" X 75"; Abrasive belts for longer life and less loading.Features; -- Central control panel features digital thickness set-up control for accurate stock height and removal. -- Four post lift design assures accurate consistent results. -- Oscillating belt is controlled by an air sensor to prevent sanding lines. -- Finishing Platen is fully adjustable and can be removed. -- Multiple dust ports for efficient dust management. -- Independent motors run the sanding belt, feed conveyor, and table elevation for maximum power to each operation.

OLIVER 4430 20" PLANER WITH HELICAL HEAD20" Maximum stock width cap., 1/4" to 8" max. stock thickness, 10" minimum stock length. Equipped with: -- 5 HP Main drive motor and mechanical raising and lowering of the cutter head. -- Fixed bed height of 29-7/8". Table dimensions 20"L X 21"W. Overall all table dimensions with infeed and outfeed bed extensions 51"L X 21"W. -- 3-1/4" Dia. Helical Cutter Head with 4-sided carbide inserts. -- Auto-Depth lock via nitrogen-charged cylinders eliminates snipping. -- 8" Max. thickness adjustment via handwheel includes LED Digital readout for head positioning. -- 4-Post support for proper head alignment.Complete with: -- 5" Dust outlet and built-in mobile base for ease of movement

OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)

OLIVER 4455 22" Straight Knife Planer, 5 HP single phase or 10 HP, 3-Ph.The OLIVER "4455" Planer has a super-wide capacity, it'll handle stock up to 22" wide, and takes up to 3/16" off in a single pass.Specifications: -- 4-Knife HSS straight knife cutter head. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on an uneven stock, coupled with a Driven Outfeed Roller to keep your stock moving smoothly. -- Add (2) feed speeds for extra quality, a Digital Thickness Guage for quick reference, and a powerful 10 HP motor. -- Max depth of cut 3/16" min part length 10"; Max work pc 22" w x 9" Thickness.

OLIVER 4470 25" Shelix Cutterhead Planer; 10 HP motor Single Phase, or 15 HP 3-Phase motor. Full 25" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through , Byrd Shelix Cutterhead this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor.

OLIVER 15" Planer with Helical Cutterhead - 10014, 3 HP (Single Phase)Unique design allows motor and cutter head to move in unison.Specifications: -- Auto-depth lock features twin nitrogen cylinders virtually eliminates snipping. -- Helical cutter head with premium carbide inserts. -- 4-Sided cutting inserts are indexed and easy to replace. -- Heavy cast iron construction including extension wings. -- Table and extensions wings are precision ground for smooth stock feeding. -- Table is fixed allowing easy use of auxiliary stock support. -- Wixey digital read-out allows precise thickness settings. -- Large handwheel and support struts allow easy height adjustment. -- Four-post design ensures head alignment regardless of stock thickness. -- Two-speed feed gearbox for better cuts, Oil bath gear lubrication for years of performance.Complete with: -- 4"; Port allows excellent dust management. -- Built-in mobile base allows easy movement in the shop. -- Magnetic switch for added protection and safety.

22"; Planer with Byrd Shelix Cutterhead - 4455B, 7.5 HP shingle phase or 10 HP, 3-phBYRD Shelix carbide inserts are indexed for quick changing.Specifications: -- Max depth of cut 3/16", min. part length 10"; max. work pc dims 22" w x 9" thickness. -- (2) Adjustable Bed Rollers, plus one infeed and one outfeed roller. -- Cutterhead speed 5,000 RPM and head is equipped with (110) Byrd knife inserts. -- 2-Speed gearbox provides the perfect feed rate of 20 and 30 FPM.Features: -- Massive cast iron construction throughout. -- Polished built-in table roller assists movement of rough stock. -- Segmented infeed roller and sectional chip breaker easily handles rough stock. -- Magnetic controls with emergency off switch for safer operation. -- Digital readout allows precise thickness settings. -- Hinged access to cutter head and feed rollers for quick set-up. -- 3 V-belt drive smoothly transfers power to drive train and cutter head. -- Easy access to the motor, drive train, and gearbox assists in maintenance and adjustment. -- 5"; Dust chute easily handles chip removal (requires approx. 900 CFM) -- Powerful EFC motor available in single or three-phase. -- Single phase motor 7.5 HP, 220V Only (38 Amp)

OLIVER 4705 SHAPER 5 HP, Sigle phase or 7.5 HP, 3-PhSpecifications and Features: -- Massive cast iron precision ground table provides a solid work surface. -- Cast iron base provides a steady platform. -- 3/4"; and 1-1/4"; interchangeable spindles are included for added versatility. -- Three spindle speeds allow more choices to produce a better finish. -- Reversing spindle gives more options for each set-up. -- Innovative dovetail design accurately raises and lowers the spindle. -- Fence is independent and features micro adjustments for quick set-up. -- Top mounted control panel includes a digital readout for spindle height. -- Large hand wheel for quick spindle height adjustment. -- Magnetic controls with emergency off switch for safer operation. -- Includes miter gauge. -- Spindle Speeds: 5,000, 7,000 and 10,000 RPM. -- Maximum Tool Diameter: 7"; Below Table, 8"; Above Table. -- Spindle Diameter: 1-1/4"; and 3/4"; Interchangeable. -- Vertical Spindle Travel: 4". -- Table Height: 36-1/2". T-Slot: 3/4" x 3/8". -- Dust Port Diameter: 4". -- 800 CFM min. -- Optional collet for router bits available special order --[1/2" Spindle for Models 4705 & 10047 Shaper]1/2" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[3/4" Spindle for Models 4705 & 10047 Shaper]3/4" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[1" Spindle for Model 4705 Shaper]1" Spindle for Model 4705 Shaper$99.99Model 4705[1/4" Collet for Models 4705 & 10047 Shaper]1/4" Collet for Models 4705 & 10047 Shaper$69.99Model 4705[1/2" Collet for Models 4705 & 10047 Shaper]1/2" Collet for Models 4705 & 10047 Shaper$59.99Model 4705[1-1/4" Spindle for Model 4705 Shaper]1-1/4" Spindle for Model 4705 Shaper$99.99Model 4705 prices may vary.

Front/rear trim Top/bottom trim Top/bottom bevel Moulding Edgesanding

OMAB GRU-100 (BACCI Style) 4-Spindle Copy Lathe/ShaperSpecifications: -- Capacity: (4) Spindle duplicating/carving/copy heads with (4) copy belt sanders for asymmetrical parts. Max. working height: 6.5" (165 mm), max length capacity 39.4" (1000 mm). -- Speeds: (3) Carriage speeds: 3 IPM (75 mm/Min)_up to 7.87 IPM (200 mm/Min). Spindle speeds: 25 minimum to 42 maximum RPM. Features: -- Carriage feed motor 1.8 HP. Cutter drive motor 2.2 KW (3.9 HP). Bell cutters 1.38" (35 mm), Minimum working radius 0.71" (18 mm). -- Comes with: Installed cup-style cutters. -- NOTE: Larger diameters are possible by using every second carriage position, i.e. (2) heads instead of four heads. -- Dimensions approx 94" long x 37" wide x 78" High . Weight about 2400 lbs NOTE: Specifications are from similar BACCI lathes and need to be verified prior to purchase.

Single horizontal drill and dowel; 1300 mm work table with four fields; sure shot revolver system to guarantee the fastest cycle time, average one second, and extreme reliability; simple user friendly touch screen; heavy duty steel frame for maximum rigidity; large phenolic table with robust clamps suitable also for delicate materials; barcoding and ethernet ready; laser for measuring the part and populate the program;

OMAL INSERT 900 CNC Bore, Glue & Dowel Inserter, Never UsedNOTE: Machine control is currently not operational; Seller believes it is its battery.Specifications: -- Capacities: X-Axis 900 mm (35.44"), Y-Axis 40 mm (1.57") Stroke, Z-Axis 10 - 40 mm (0.39" - 1.57") Thickness. -- Table size 15-5/8"; x 49"; x 35"; H, (4) Working zones: (2) 450 mm (17.72") W. -- Max. dowel size 8 mm Dia. x 30 mm L (0.31" dia. x 1.18" L). -- Max. dowel projection 15 mm (0.59"). -- Spindle speed 6,000 RPM. -- Cycle time 0.8 Sec.Equipped with: -- (4) 2-1/4" Dia. Pneumatic hold-downs. -- (1) Horizontal drilling unit, with: 3/4 HP - 3,380 RPM TEFC Motor, (1) Glue injection unit & (1) Dowel insertion unit. -- PC-Based controller, with 12" Display, (2) Foot pedal controls.Complete with: -- BROVIND VIBRATORI "OB 300 DC" 14" Dia. x 5-1/2"; D Vibratory Bowl Feeder, with "NC-02M-50 DC" Variable Speed Controller. -- (1) 8 L Cap. High Pressure Glue Tank, (1) 8 L Cap. Water Tank. -- METROLOGIC "VOYAGER CG MS9540" Handheld Bar Code Reader.

OMAL VELOX 1300 CNC BORE, GLUE & DOWEL INSERTER + Optional LASER MEASURING DEVICE SpecificationsPLC Controlled automatic step-by-step boring, glue injection, & dowel insertion into panel components, drawer parts, chair pieces, etc. at random spacing. Features"Optional" Auto Laser measuring device with: Parametric Control and Touchscreen PLC Control. Working Capacity51" (1,300 mm) In "X" Axis work area; 1.57" "Y" Axis stroke with manual depth setting; 1.57" "Z" Axis stroke with manual vertical settings. -- 10 mm to 30 mm (0.39" - 1.18") Material thickness capacity in the "Z" axis. -- Machine is currently set up for 8 mm dia. x 30 mm long max. dowel dimension.Work Areas(2) Loading zones with: Cycle time of (1) second for each bore, glue and dowel insertion when holes are on 32 mm intervals. -- Equipped with: Brushless motor; ball nut and ball screw for quick positioning.Dowel InserterOMAL "SURE SHOT" Revolver system guarantees a dowel is inserted every time. (1) Dowel insertion unit with: 8 mm Diameter dowel capacity -- Standard dowel dimension: 8 mm x 35 mm; Maximum dowel length: 40 mm; Maximum dowel projection: 14 mm.Operator InterfaceTouchscreen Control for writing and storing programs & is programmable in the "X" Axis. -- Graphics programming 2.5D with: Simultaneous working display; Automatic Mirror Image (left & right) programming; Parametric programming; Graphical aid.Internal self-diagnosis; Historical report of alarms, Complete with:(2) Working zones, (1) horizontal drilling unit, (1) gluing, (1) dowel insertion unit.(1) 8-Liter cap. high pressure Glue Tank, (1) 8-liter cap. Water Tank (for cleaning), (1) Vibratory Dowel Hopper, (4) pneumatic Holddown Clamps, Dual foot Pedal controls. -- Actual Model is: OMAL VELOX 1300

OMAL INSERT 900 CNC BORE, GLUE & DOWEL INSERTERSpecifications: -- Capacities: X-Axis 900 mm (35.44"); Y-Axis 40 mm (1.57") stroke; Z-Axis 10 - 40 mm (0.39" - 1.57") thickness. -- Table size; 15-5/8"; x 49"; x 35"; H; (4) working zones: (2) 450 mm (17.72") W. -- Max. dowel size: 8 mm Dia. x 30 mm L (0.31" dia. x 1.18" L). -- Max. dowel projection: 15 mm (0.59"). -- Spindle speed: 6,000 RPM. -- Cycle time: 0.8 Sec.Equipped with: -- (4) 2-1/4" Dia. pneumatic hold-downs. -- (1) Horizontal drilling unit with: 3/4 HP - 3,380 RPM TEFC Motor; (1) glue injection unit & (1) dowel insertion unit. -- PC-Based controller with: 12" Display; (2) foot pedal controls.Complete with: -- BROVIND VIBRATORI "OB 300 DC": 14" Dia. x 5-1/2"; D vibratory Bowl Feeder with: "NC-02M-50 DC" Variable Speed Controller. -- (1) 8 L Cap. High Pressure Glue Tank; (1) 8 L Cap. Water Tank.

OMAL HBD 2500 CNC BORE, GLUE & DOWEL INSERTER: Specifications: -- NC Controlled, automatic step-by-step boring, glue injection & dowel insertion into panel components: Drawer parts, chair pieces, etc. at random spacing or automatic hole-spacing with simple what-if statement: i.e. parametric programming.Working Capacity: -- 2,500 mm (98.4") In the X-axis; 30 mm (1-1/4") stroke in the Y-axis; 10 mm - 40 mm (0.39" - 1.57") thickness capacity in the Z-axis. (4) Working zones: Center fence and both side fences dropdown for 2- or large 1-zone operation.Tool Plate Configuration: -- X-Axis rack & pinion drive CNC Controlled; carriage speed of 90 MPM (295 FPM); Y- & Z-axis: Manual ball screw with digital indicators.Equipped with: -- (1) Horizontal drilling unit with: 3/4 HP - 6,000 RPM Motor; (1) gluing & (1) dowel insertion unit.Control System: -- PC Numerical Control operating system; Windows/XP, color video flat screen monitor; 40 GB hard drive; keyboard & mouse. -- Graphic operator inter-phase, parametric programming standard; OMAL patented "SURE SHOT" Revolver System with fiber optic sensor to guaranty reliable dowel presence & insertion.Complete with: -- (1) 18-Liter (4-3/4 Gallon) cap.; high pressure glue tank. -- (1) 18-Liter (4-3/4 Gallon) cap.; water tank (for cleaning). -- (1) Vibratory Dowel Hopper, (6) pneumatic hold-down clamps; machine is setup for 8 mm dowels.

OMGA Radial 1250-7 Radial Arm Saw -- Specifications: 7 HP Saw motor, 43.897" crosscut cap. at 90°; 6-7/8" thickness cap. at 90°, 4-7/8" at 45°; 59" rip cap.; 20" dia. blade with 1" bore; 1-3/4" max. dado cap.; 3,400 RPM Arbor Speed. -- Features: Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- 180° Swivel of entire saw carriage for mitered crosscuts. -- 45° Saw head tilt for compound miter cuts. -- Complete with: Spring loaded return for safe return of saw head after completion of the cut; 58" x 44" replaceable wooden tabletop with full length back fence; fabricated open steel base; electromagnetic brake to stop the blade within (2) Seconds. -- Includes: Magnetic controls, push button controls & thermal overload switch. -- OPTIONAL EQUIPMENT WHEN ORDERED WITH MACHINE: -- Automatic Air-Over-Oil Head Feed System, foot pedal activated, add $4,379.00 -- Vertical Pneumatic Clamp, add $ 675 -- Horizontal Pneumatic Clamp, add $929 -- RH or LH Roller Table, 6'-7" X 24", add $1,687 -- 3' Aluminum Fence Extension, add $410 -- 6' Aluminum Fence Extension, add $580