Woodworking Equipment For Sale

CANTEK - MX340, ...Edgebander (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MX340 EDGEBANDER (COMPACT): (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications: -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations: -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MX340M Edgebander (Single Phase):The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thiknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Also available in 220V/3PH/ 60 Hz

CANTEK MX340M Edgebander (Single Phase) --The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thickness of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed). --Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon-coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double-pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK MX340M EDGEBANDERThe MX340 from CANTEK is designed to be a compact, and durable edgebander.Specifications: -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad. -- The MX340 handles panel thickness of 0.315" up to 1.77" (8 mm to 45 mm), -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed). --Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon-coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring-loaded double-pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK MX350 EDGEBANDER (W/ PRE-MILLING): -- Specifications:0.4-3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWorkstations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK MT-610 24"; Rotary Milling PlanerSpecifications -- Heavy duty welded steel construction. --Moving table type -- Display position number. -- Alarm bell and flash light. -- Speed change for feeding, controlled by Inverter (VFD) -- Rubber Endless Belt. -- Automatic device for feed belt tracking. -- Air jet cleaner for cutter -- Working width 610mm -- Workpiece thickness 3-125mm Equipped with & Features -- Number of cutters 2 units -- Spindle motor power 20 HP -- Brush motor power 1 HP (150 mm dia) -- Vacuum motor power 1 HP (suction for conveyor belt) -- Feed motor power 1 HP -- Lifting motor power 0.5 HP

CANTEK LBS300-5S 3-Sided Moulding Sander5-Head Brush Sander, 11" width and 4" height cap., for 3-sided sanding of linear profiled material. Head Configuration: -- (2) Sets of Top abrasive brushing heads with variable speed adjustment by inverter, 0.75 HP (0.55 kW) motor each. -- (1) Left side head, adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- (1) Right side sanding head which can be adjusted up/down and in/out, 0.5 HP (0.37 kW) motor. -- (1) Left side sanding head is adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- Brush head spindle speed adjustable from 200 - 1,200 RPM. -- Variable feed speed of 6.5 - 27 FPM, adjustment by frequency inverter.Features & Specifications: -- Min. workpiece length 26", min. workpiece thickness 3/8". -- 0.25 HP (0.18 kW) Conveyor motor, 0.33 HP (0.25 kW) moving brush head motor. -- Depending on the application, brushing heads can be cleaning brushes or abrasive cloth brushes. The dovetail pocket design allows for easy abrasive/brush replacement. -- Centralized control panel for operator convenience integrated into machine base.Also available in 460V, 3-Ph, 60 Cy (factory order only – app 10-12 weeks)

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300mm) for both straight and profile grind; dia. of knife swing 12" (300mm). Grinding arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1500 to 4200 RPM. Quick change removable (140mm) wheel adapter. Machine set for axial constant grinding and template set up on right hand side. Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10°/15°. Quick change stylus turret for applications. (6) included with machine. Carriage: SCHNEEBERGER lineal bearing table movement. Table movement 12" x 6". Coolant system: 1/8 HP motor from coolant pump located in tank below. (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout!Option included: Motorized Side Clearance – including set left and set right Motorized Wheel Back Clearance Angle Motorized Grinding Wheel In/Out

CANTEK RAPIDEDGE PRO EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Pre-mill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counter rotating cutter-heads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutter head that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. -- Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Pre-milling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface

CANTEK R-18 Heavy Duty Straight Line Rip Saw "Cuts From The Bottom"Equipped with & Features: -- Extra Heavy Main Frame Throughout with large support table. -- 6"; Minimum length with this type of saw the blade is cutting downwards, forcing the Blade onto the chain – hence max. stability and safety are realized. -- Better chip clearance for shavings on deep cutting. -- Glue Joint Range – 12"; to 10 Ft.Specifications: -- Depth of Cut 4.7"; (120 mm) max. -- Split chain – double track with HRC60 Rockwell Hardened Guideways. -- 26"; (660 mm) Saw to Column. -- (8) Press Rolls hold material firmly on the track. -- 20 HP Main Motor. -- 3 HP Feed Motor. -- Feed Speed 42 to 164 FPM variable. -- Automatic chain and track Oiler -- 41"; Length of chain above table -- Saw Arbor Height adjustable -- Max. 18"; Blade Diameter x 2"; Bore Dia. saw Arbor with 14 mm pin at 6 5mm centers.Complete with: -- Saw Arbor Brake Included -- Anti-kickback fingers top and bottom -- Dust collection outlets: Top 4" (100 mm), Bottom 6"; -(150 mmm). CFM Required: 1,400 CFM. -- Table Dimensions: 78-3/4"; x 40"; x 33.5"; high (Can be added to optional) -- Net weight - 4400 Lbs. -- Stock Machine Electrics 460/3/60 to UL/CSA Standards (Other voltages available on request)Note: The advantage of cutting from below on thick material, the gullet of the sawblade projects above the stock to clear the shavings halfway through the cut

CANTEK SRS330 Straight Line Rip Saw;Features: -- Very Rigid machine body with a welded steel frame with an integral cast & machined table, which is fitted with a sturdy cast column & saw unit. -- Excellent precision work accuracy and durability. -- Absolute straight line feeding up to 13 ft. of ripping. -- Precision caterpillar chain and double "VEE" extra long (47.2";) guide rails are made of special cast iron the chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Holddown rolls (6 rows).Specifications: -- Max. work piece thickness 4.33". -- Min.work piece length 8". -- Distance between saw and column 18.1". -- Saw arbor dia. 1" and Saw blade dia. 10"; - 14". -- Saw arbor speed 4,300 RPM. -- Useable Chain Length 47";. -- Glue line guarantee 13’ (+/- 0.0098"; or 0.25 mm). -- Feed speeds variable 30 to 130 FPM. -- Arbor motor 20 HP -- Feed motor 2 HP -- Table size 36.6" x 64.6, Table height 31-7/8". Utilities: -- 230 V = 60.8 Full Load Amps. -- Electrics 460/3/60 = 30.4 Full Load Amps. -- Dust Collection Outlet 4"; -- Net weight 3,190 Lbs.Available Options: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03) -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)

CANTEK SS512CSB Heavy Duty Production Shaper with Sliding Table & Spindle Brake7.5 HP Features: -- Cast iron sliding table runs on ball bearing for smooth table transition. -- Cast iron ground & polished table with insert rings; table size: 31- ½"; x 39.4″. -- Precision ground and electronically balanced spindle. -- V-belt drive with (5) feed speeds is easily accessed from the front of the machine. -- Electric spindle brake for added safety. -- Spindle lock - with limit switch safety, machine will not start with lock engage. -- Micro spindle height adjustment with dial indicator. -- Interchangeable cutter spindle. -- Forward/reverse spindle rotation. -- Adjustable "finger" type fence Independent micro-fence adjustment on both sides. -- Includes the following standard equipment: 1- 1/4" Spindle, (1) 5"; dust chute on guard & (1) 4"; dust chute in the table, safety guard, Miter tenon jig, and Telemecanique magnetic controls.Net weight 1034 Lbs. Machine dimensions 48.4"; x 39.4"; x 52 ¾";. Shipping weight 1166 Lbs.Shipping dimensions 45 ¼"; x 37"; x 41";

CANTEK - SS512TB Tilting Spindle ShaperSpecifications: --Tilting spindle from -5° to +45° and 6" x 43" fence. --1-1/4" interchangeable spindle is standard (other sizes available). -- Large cast-iron table is ground and polished for maximum stability and durability. -- Powerful 7.5 HP motor for even the most demanding profiling work. -- Five spindle speeds can be easily adjusted to suit your tool diameter. -- 5-1/2" Useable spindle length, above table 13-¼"; below table 8-¼". -- Electronic spindle brake for added safety and facilitates fast changeover. -- Precision fence assembly with micro-infeed and outfeed fence adjustment. -- The finger-style fence allows the fence to be adjusted around the cutter for added safety and workpiece stability. -- Table size 31 ½"; x 39.4″. -- Dust port (1) 5″ on guard, (1) 4" into the table.

CANTEK 1214 TABLE SAWHeavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 10 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK TA-14 Tilting Arbor Table Saw. -- Heavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 7.5 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK SS-512TSB Tilting Spindle and Sliding Table Shaper:7.5 HP - 3-Phase motor, overall table dimensions 31.50" x 39.40", sliding table 10.25" x 39.40". -- Spindle stroke 7"; 1-1/4" dia. spindle with 5 MT receiver and 4-3/4" cap. under the nut. Spindle tilts -5° & +45°. -- (5) Spindle speeds: 3,000, 4,000, 6,000, 8,000 & 10,000 RPM.Complete with: Spindle reversing switch, micro-adjustable fence 6" x 43", thermal overload protection and dust hood.16 weeks delivery.

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large-diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents the backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self-centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus unwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

CARLSON CD PINNER PLUS Cabinet Door Clamp & Pinner; 30" Wide x 48" High max. Capability. The ProMax Cabinet Door Pinner is an affordable system that squares, clamps and fastens a variety of cabinet door styles and sizes. This machine is designed to handle stile widths between 1-1/4" and 3-1/2" in 1/8" increments and any rail widths. Standard product minimum: approximately 7" wide X 6" tall for 2" stile and rail cabinet doors. Standard product maximum: approximately 30" wide X 60" tall for 2" stile and rail cabinet doors.General Specifications: -- Standard joy stick operation allows quick and accurate size adjustments. -- The frame is ergonomically designed at an angle for easy placement of sub-assembled door parts and fast removal of the finished product. -- Operating controls are simple and convenient to minimize training time. -- Machine functions are air powered with programmable electrical controls for accurate and reliable operation.Includes: -- Air motor drive system. -- Standard clamp pads. -- Cope & Stick door fastening. -- Spare tool assembly. -- Size upgrade - Height 60". -- Miter capability. -- Safety light curtain. Features: -- Heavy duty frame, low maintenance, powered size adjustments, precision linear bearings, overhead mar-proof clamping, programmable controller.