Woodworking Equipment For Sale

BLACK BROTHERS - 22-D-1175-56, ...Glue Spreader or Roller CoaterNominal length: 56"; 11-3/4" dia. applicator, doctor & feed rolls, lower elevator. -- Setup to 0" - 4-1/2" thick. -- Neoprene applicator rolls: 16 TPI and Neoprene smooth doctor rolls. -- Single feed speed drive, passline height 30".Complete with: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout, and cleanup pan.Can convert to Upper Elevator for an additional price.Can Convert to Variable Speed for an additional price.(4 - 6) Weeks on complete rebuild.

Boarke 3-Head Wide Belt Sander 43" Capacity Model BKM-43103 RPKV

BOARKE 43 RK Wide Belt Sander, (2) Heads43" Width cap. Drum, Combination HeadHead Configuration1st Head: Contact Roll for Calibration 10"; Dia. Contact Roll, 85 Shore Hardness Dynamically balanced, 25 HP, 230/460 V, wired 230 V2nd Head: Combination Unit for Finish Sanding with ContactRoll, Pad or Both 5.5 “dia. Contact Roll 55 Shore Hardness, Dynamically balanced, 2.8"; wide Finishing Pad, 20 HP, 230 / 460 V, wired 230 V.Specifications: -- Sanding Units include: Photo electric belt tracking, Large diameter Tension, and Idle Rolls, Rigid Main beams for superior accuracy, 2.8"; Dia. spring loaded hold down rolls Quick release Tie Down Blocks, Y Delta Motor Starters -- Feed System: 4 ea. 5 ton capacity lifting screws, Heavy Duty 3-Ply conveyor belt, Heavy slider bed, machined for accuracy -- Variable conveyor speed from 7 – 45 FPM, Inverter Controlled Variable Speed, 2 HP drive motor, Conveyor belt centering device -- Infeed Roller, Guide Ways provide accurate vertical movement -- Control Panel (Located on Belt Loading Side for convenience) -- Digital Controller positions machine thickness -- Digital Readout in Inches or MM, And ν Buttons micro-adjust thickness in 0.001"; increments, Micro-Adjustment hand wheel for final thickness in 0.001"; increments -- Automatic Thickness Set Up, Motorized Thickness adjustment -- Amp Meter, and Volt MeterEquipped with & Features: -- Over Thickness Shut Off, Body activated safety switch at front of machine -- Door activated safety switches on ALL Doors, Emergency Stops front and rear -- UL / CE approved electrical components -- Disc Brakes on both motors -- Emergency Shut off activated when Air Pressure is too low, Overloads are tripped -- Emergency Stops are activated

37” Capacity single head 230 volt 3phase

Boarke 43" 2-Head Sander

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

50” width drum/drum/platen heads 480 volt 3-phase Bottom and top sanders can be sold separately Pictures coming for bottom sander

BOERE TPK-900 Planer Sander 2 Heads -- 2-Head, 900 mm (36") width cap. equipped with (1) Knife planer head and (1) Rubberized Drum. -- 1st Head: Helical knife planer head with (4) spirals of 4-sided carbide inserts each 14 mm x 14 mm, 20 HP motor. -- 2nd Head: Drum, approx 10" dia. rubber covered contact roll, 15 HP motor; all heads with air operated caliper type disc brakes. -- Variable feed speed 13 - 52 FPM, 2.5 HP motor, automatic conveyor belt tracking, anti-kick back fingers on infeed, infeed hold down shoes and double outfeed pinch rolls on outfeed. -- Motorized part thickness adjustment 0" - 6" with LED read out display . Complete with: -- Controls mounted on belt loading side, load meters for each head, conveyor infeed extension.

BOERE - TK 1300, ...Abrasive Planer -- (1) Head, 51" width cap. x 6" thickness cap.; 10" dia. spiral rubber-covered contact drum, 50 HP motor. -- Abrasive belt size 52" x 75", air tensioning, and BO-TRACK electronic abrasive belt tracking. -- 2 HP Variable feed speed motor for 16 - 82 FPM. -- Single infeed rubber-covered holddown roll, followed by floating shoe on the infeed, and single outfeed rubber covered holddown roller followed by rotating cleaning brush. Complete with: -- Motor load meter, (4) corner mounted screw jacks with powered bed raise & lower, and 9-3/4" dust port.

BRANDT KDN 650 C Edgebander; 6-Station Edgebander with 0.4 - 8 mm (5/16") Edge capacity. Specifications: -- Panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; -- Line control (NO limit switches) for workstation function. -- Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator. -- PC-16 Program Control with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; -- Signal infeed light to insure proper spacing between panels. Equipped with: -- Quick heat-up glue system (10 to 12 minutes). -- Automatic magazine for strip & coil stock (large coil table 800 mm diam. to accommodate large coils of 3 mm PVC), 3 mm PVC guillotine; -- (1) Drive plus (3) idle roll "pneumatically controlled" pressure sections. Workstations: -- End trim (1/3 HP - 12,000 RPM motors) chamfers 0° - 15°; -- Top & bottom flush trim, bevels 0° - 15°, (2) 1/2 HP - 12,000 RPM motors) with insert knives. -- 2-Motor (4-corners) contour trim for profile corner rounding (2) 1/2 HP - 12,000 RPM motors), with insert knives for 3 mm PVC radius. -- Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. -- Last Station: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Feed chain track speed 42 FPM, 2 HP feed drive. Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling.

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

Brandt KDF 650 Edgebander

Brandt Ambition 1110 Edgebander

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT "KDF-980 2C" EDGEBANDER WORTH PRE-MILLING & CORNER ROUNDING 0.4 - 20 mm (3/4") Edge thickness capability; Min. workpiece width 65 mm (2-1/2") and min. panel length 160 mm (6-1/3"), panel thickness 8 - 55 mm (5/16" - 2-3/16") .Working height 900 mm (35"); 80 mm wide Heavy Duty feed chain w/rubber pads, automatic chain track lubrication, 3 HP (2.2 kW) feed drive for variable feed speed 11 - 20 MPM (36 - 65 FPM) (max. using solid wood 52 FPM); motorized upper pressure beam.7.4" Matrix color LCD Screen "PC-16" Integrated Microprocessor Line control for programming the various working functions; features internal modem for remote diagnostic link.Pre-Milling Station, (2) 3 HP (2.2 KW) - 12,000 RPM Vertical milling/jointing heads, electro-pneumatic jump control, heads counter-rotate, SIKO digital units for vertical & horizontal adjustments.Quickmelt gluing system with large granulate hopper with automatic glue feed system (approx. 12 Min heatup time); pre-melting unit between hopper and reversible & retractable glue roller; infrared radiant glue heat zone between glue roller and pressure section for optimum gluing strength.Automatic magazine for strip and coil feeding with automatic coil feeding system; 2-coil table for one roll thick PVC and one for thin edgings; wide magazine with automatic feeding of wood strips; program controlled.Motorized pressure section with (1) large driven pressure roll and (4) secondary idle rollers with pneumatically controlled side pressure; solid wood infeed device.Workstations Edgebanding:End Trimming (1 HP / 0.75 kW) - 12,000 RPM motor, program controlled pneumatic indexing of straight or chamfer trimming, chamfers up to 15°.Top & bottom rough (flush) trimming (2 HP / 1.5 kW) - 12,000 RPM motor ea. w/vertical tracing.Top & bottom fine trim (0.75 HP /0.55 Kw) - 12,000 RPM motor ea., bevel 0° - 25° tilt angle, w/vertical & horizontal tracing, servo driven in/out adjustment controlled from control panel.Corner rounding unit with (2) motors ( 0.50 HP / 0.4 Kw) - 12,000 RPM motors ea, 16 MPM (52 FPM) operating feed speed, pneumatic (in/out position) control from control panel (all trim station motors are 200 Cy HF and equipped w/electronic brakes). Top & bottom scraper for finishing PVC edging.Hot air blower (post heating) for reactivating scraped, thick PVC edgebanding.Top & bottom "oscillating & jump" buffing unit (0.3 HP - 2,800 RPM motors), tilt vertically & horizontally.Complete with: All working units & fence adjustment throughout machine with SIKO digital readouts, operator controls on overhead swivel arm.Includes: Sound enclosures with 1" thick padding over all milling stations in edgebander section, and digital counter at infeed to measure footage of product edgebanded.A 20 year old machine with 3573 hours on it !only ran for 15 hours per month all parts and tech support available from Homag Brandt

BRANDT AMBITION 1650 FC High Flex EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications: Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Equipped with:3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 kW, 3 kG (6.61 Lbs) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- Quick-change glue tank for easy maintenance & glue color change, melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improve edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electro-pneumatic reset for straight or chamfer trimming. -- Top & Bottom Multistage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with a slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (2) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different radius profiles, pneumatic (2) position indexing for different edge thicknesses

BRANDT AMBITION 1680 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) -- Specifications: Edge thickness: 0.4 - 12 mm (0.02" - 1/2"); incl. 3 mm (0.12") PVC banding. -- Workpiece: Thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width: 70 mm (2.76"); min. workpiece length: 160 mm (6.37"). -- Working height: 950 mm (37.8"). Equipped with: -- 3 HP (2.2 kW) Feed motor; variable feed speeds from 26 - 59 FPM (8 - 18 MPM); applying solid or using corner rounding units. -- Heated Infeed Fence. -- Infeed panel support with: Roller guide extends out to 800 mm (31.4"). -- Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") Wide Heavy-Duty feed chain with: Rubber pads, automatic chain track lubrication. -- Top pressure section with: Double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency motors); line control (no limit switches) for workstation functions. -- Top & Bottom spraying device: Located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") height. -- Centralized Lubrication system.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads; electro pneumatic jump control on 1st motor; electronic frequency inverter for control of motor speed & braking; SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 kW, 3 kG (6.61 Lbs.) cap.; glue viscosities: 25,000 - 80,000 mPa; temperature range: 120° - 245° C (248° - 473° F); max. melting capacity 6 kG/Hr.EVA Hot Melt Glue Application System: -- Quick change glue tank with Premelter for easy maintenance & glue color change; melting capacity: Approx. 6 - 10 kG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electro-pneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different ra

BRANDT KDF 660 2C EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications:Work-Capacity 0.4 - 8 mm Edge cap; 8 - 55 mm Panel thickness; 160 mm (6-3/8") min. panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Feed-Speed 14 MPM (11 MPM automatically when corner rounding). Equipped With: -- Pre-Milling Station, for cleaning edges of panel. -- Quick Change Gluing System, for maintenance & glue color change. -- Automatic Magazine for strip & coil stock, 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" & Servo controlled pressure sections for quick edge thickness changeover. Workstations -- End Trimming: Double motor (2 x 0.5 HP - 12,000 RPM motors), automatic chamfer from control panel 0ø - 15ø. -- Pre-Flush Trimming: Top & bottom (2 x 0.5 kW approx. or 0.67 HP - 12,000 RPM motor) with (4) pre-set position index settings. -- Fine/Bevel/Radius Trimming Station: Top & Bottom (2 x 0.35 kW approx. or 0.50 HP - 12,000 RPM) bevels 0ø - 25ø, with combination flush/radius/chamfer cutter heads; horizontal & vertical tracing wheels, comes with optional brushless Servo motors for quick thickness changeover. -- Corner Rounding Station: (2 x 0.35 kW motors or 0.5 HP - 12,000 RPM motors) for leading & trailing edges of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Profile Scraping Unit: Top & bottom PVC radius scraping with pneumatic control, PVC Scrape collection box. -- Flat Glue Scraping Unit: Top & bottom glue-joint scrape station. -- Buffing Unit: Top & bottom (2 x 0.125 HP - 1,400 RPM motors).Complete With:&#9679 Operator Control Panel, Power Control PC 20+ with color LCD screen & soft keypad. &#9679 All trimming stations have HF motors w/electronic brakes. &#9679 Padded sound enclosure and used tooling. -- 220/480v, 3Ph, 60Hz transformer. -- Actual Model is BRANDT KDF 660 2C