Woodworking Equipment For Sale

HOMAG KAL 210 AMBITION 2262 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.3 - 3 mm (0.012. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor.Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG KAL 310/4/A3/S2 Edgebander (w/Pre-Milling): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

HOMAG KAL 310/7/A3/S2 EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING)Working Capacity: -- Edgebanding thickness in rolls (min/max) 0.3 - 3 mm. -- Panels thickness (min/max) mm 12 - 60 (1/2" through 2-3/8"). -- Feed speed (adjustable) 18 - 25 MPM (59 to 82 FPM). Front-End Equipped: -- In-feed fence, manual digital positioning. -- Pre-Milling Unit (vertical joint trimmers) (2) x 3 Kw each. -- Lamps to pre-heat the work pieces edge. -- Edge Magazine, vertical coil cart with 2 positions. -- Gluing Unit QA 34, EVA (Hot Melt) -- Side Pressure Zone, (3) rollers, adjustable by N.C. servo motor. Working Units: -- End Trimming Unit HL 81 Motors, 2 x Kw 0.22 (0.50 HP) -- Pre-Rough Trimming Unit: Top/Bottom, 2 x 0.55 Kw. (0.75 HP) 12,000 RPM motors, none tilt with digital indicator positioning. -- Multi Function Unit FK 11: Profile Contour Trimming, 2 x 0.4 Kw, 12000 RPM motors, for linear top/bottom edge trimming and vertical front/back corner rounding. -- Profile Edge Scraping Unit:Pneumatic in/out and manual digital indicator positioning. -- Glue Scraper:Top/Bottom, flat panel surface glue scraper. -- Buffing Unit: Top/Bottom oscillating buffing motors 2 x 0.25 Kw (0.35 HP).Operator & Machine Control: -- HOMATIC NC 21 controller, flat color LCD screen with keyboard and mouse input. Complete With: -- Top pressure system with rubber belt. -- Panel Support Outrigger. -- Sound and safety hoods over all working stations. Actual Model is HOMAG KAL 310/7/A3/S2

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

Houfek Maxx 1100 2 Head Widebelt Sander43 width cap Drum, Combination headHead Configuration1st Head : Contact roll2nd Head : Combination contact roll and finishing platen.Specifications -- 1st Head: 6" Dia. rubber covered contact roll, 25 HP motor; -- 2nd Head: Combination head with rubber covered contact roll 6" Dia. and air cushioned finishing platen, timers control platen inflation and deflation, 20 HP motor. -- 43" x 75" Abrasive belts, -- TRU-TRAK solid state belt tracking, -- Variable feed speed with inverer control 15 - 45 FPM -- 1 HP motor, endless belt conveyor with automatic tracking. Equipped with & Features -- Motorized part thickness opening with LED 0" - 6" opening. -- Infeed and outfeed rubber covered holddown rolls, -- Infeed over thickness bar, -- Emergency stops at infeed & outfeed, -- Air operated disc brakes on sanding heads, -- Electrical interlocks on main access doors, and motor load meters.Note from Seller :This machine was damaged by the straps going over the machine during transport. The doors work fine, they just have dents on the top where the straps dented them. Price has been reduced to reflect this (cosmetic) damage.

Hunton Limited Punch Grinder

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

2004 Hymmen Proficoater 60" Roll Coat Line - Model ULX-S: Includes spare drum and lights SCMI Finish Sander

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA Combiform I/R75/1260/V

MA Hot Melt Glue Edgebander, Designed to allow operation by feeding parts past the glue head using the table and ball rollers, or the part can be vacuum mounted to the table (Vac Pump and Vac Pods included) with the head guided manually around the part with the weight of the applicator head counter-balanced from the boom. Specifications: Board Thickness 16mm to 45mm(0.630" - 1.77"), Strip Height 20mm-50mm (0.78"-1.97"), Strip Thickness 0.4mm to 3mm (0.016" - 0.118"), Glue Tank 0.8Liter (48 Cubic Inches, or 0.8 quart ), Processing Temperature 140 to 220 C Degrees ( 284F-428F). Current running 8 Amps, Glue Pot 1400 Watts, Max Overall Watts 2600. Weight of Movable head 20kg ( Note: this 45 lbs head weight is counter-balanced with spring.) Working height 960mm (37 3/4")

IMA 500L Edgebander Will need a new touch screen control and calibration.

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L

Specifications comming

IMA BIMA-610, 4' x 16’ CNC MACHINING CENTER , (1998), (460/60/3 electrics), S-4535 General Specifications: - 10 HP, 230/460/60/3 tool-changer type router spindle - (12) station traveling rotary tool changer - (1) 7-spindle & (1) 5-spindle point-to-point vertical drill blocks - X & Z axis ball-screw & Y-axis rack & pinion - Adjustable pod and rail system, (10-rails with pods) - Can include a 4’ x 8’ “universal” flow vacuum table for nested base processing - Integrated scrap conveyor under/through the working area - IMAWOP, (Windows workshop-oriented PC programming system) - Hand held start/stop spindle speed control - 3 HP Becker vacuum pump for the pod & rail side - Includes computer, an aggregate horizontal boring unit, and additional tooling - Note: the retrofitted nested base table is not included - 25' long x 9'8" wide x 8' tall

IMA Bima 810 V

INDUSTRIAL IWS 10 Finger Jointer:Shaper unit will handle material 2" to 8" wide, 5/8" to 2" thick and 5" minimum length and 30" maximum length.Equipped with: -- ( 2) Trim saws with 5 HP motors, (2) Scoring saws with 3 HP motors and (2) Shaper spindles with 15 HP motors - 1-13/16" dia.. -- Feed speeds from 0 to 150 FPM. Average speed of (100) lugs per minute; feed chain is equipped with lugs on 9" spacing. -- Glue applicator with improved glue spreading and simplified pump. -- Model 3502 90° brush transfer to the assembly and Flying Cut Off Saw. -- MOD - Assembly Press, 16' long, with (1) retrim saw, air over hydraulic clamp & squeezing including Complete with: -- Wertern/Nielson 800 FJ cutterhead grinder -- Set up stand -- (15) cutterhead -- Some spare parts