Woodworking Equipment For Sale

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0° - 15°, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. -- Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17” flat screen (TFT) with high resolutio

BIESSE ROXYL 6.0 ... Feature Loaded Edgebander with "AIR FORCE" & EVA (Hot Melt) Gluing Systems.Features: -- Latest Technology combines productivity, efficiency, and flexibility for all types of edgebanding material."AirForce" emits high temperature compressed air through a slot nozzle directly onto the reactive layer of laser banding. That layer is activated and bonds the banding to the panel fibers.This technology allows changes based on banding colors without any setup. Environmentally friendly providing a “clean - green” technology that eliminates glue and fumes, which becomes timely & important. -- In addition, it features a conventional EVA (Hot Melt) Gluing System to cover the full range of edgebanding processes in use today!Specifications: -- Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). -- Machine Controls: "Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy; icons of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without the necessity to write a program.Machine In-Feed Configuration: -- Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material + a (2) position vertical Coil Magazine Cart. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System: -- EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special precoated edge material (commonly referred to as laser edge).Workstations: -- End Trimming Unit "IT90-S": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-100": Top/Bottom pre- or flush trimming motors -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (4) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-positioning of motors by pneumatic air cylinders. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to workpiece's surfaces. -- Corner Rounding Unit "CR-202": (2) Motors for front/back corner

Biesse Elix B Boring Machine

BIESSE - Stream A 6.0. ... Edgebander (w/Premill & Corner Ronding), High Production w/NC Axis PackageFeatures: -- "NC Axis Package": The machine adapts to the process being executed based on the edge's thickness and material.Machine management ...100% touch with no need for external devices. - Intelligent language management.Easy program management and usability with rapid transition from one machining operation to the next. Specifications: -- Edgebanding Capacity: Edge thickness for strips: Min./max. 0.4 - 22 mm (0.02" - 0.87"); coiled material from 0.4 - 3 mm (0.02 - 0.12").Panel thickness from: 10 - 60 mm (0.39 - 2.36"); workpiece width: Min. of 85 mm (3.34"); workpiece length: min. 140 mm (5.51").Feed speeds of: 12 - 18 - 20 - 25 MPM (39 - 59 - 65 - 82 FPM).Machine Infeed Configuration: -- Premilling Station:(2) 1.8 kW (2.4 HP) - 12,000 RPM Motors; LH & RH Counter Rotating Spindles; NC (Servo) controlled with automatic intervention that guarantees a perfect base for gluing. -- Anti-Adhesive:Automatic Spray Unit with: Glue release agent preventing glue to adhere to workpiece's surfaces. -- Infrared Heating Lamp:Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic 2-coil/position magazine for processing coiled & strip edgebanding material in real time. -- Pressure Section:Servo Controlled programmable pressure section with: (1) Large driven roller and (4) idle rollers.Gluing System w/Premelter: -- EVA (Hot Melt), quick premelting granulate with: Glue roller applicator to cover conventional edgebanding material. Workstations: -- End Trimming: Front & Rear Linear end trimmer with: Tilt Function for high speeds with (2) 0.8 kW (1.0 HP) - 12,000 RPM motors. The machine axis movement on linear tracks allows the achievement of very high processing speeds.The copying & tracing system guarantees optimal finish quality; also on high gloss edges with film. -- Flush/Bevel Trimming Unit:Top & Bottom flush or bevel trims with: (2) "Quick Change" 0.65 kW (0.8 HP) - 12,000 RPM motors. -- Fine Trimming Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors; (2) Servo motors for tool positioning (one for horizontal tool position, one for up/down tool position).Prepositioning of motors by pneumatic air cylinders while using a combination bevel/radius/flush insert knives.Absolute machining flexibility thanks to the full adjustment of the machine according to the required edge thickness. -- Corner Rounding Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors for front/back corner and upper & lower edge profiling.The controlled axis on the Corner Rounding unit supports the management of infinite machining settings. -- Profile Scraping Unit:Top/Bottom 2-axis NC programmable knife positioning (i.e. 2 - 3 mm radius) for PVC edges. -- Glue Scraping Unit: Flat, top/bottom, digital positioning indicators, pneumatic controlled for in/out position. -- Buffing Station: Top & Bottom buffing motors:

Biesse Akron 1440 PUR Return conveyor available - demo unit!

Min. Panel Thickness: 0.39? Max Panel Thickness: 2.36? Height of Edge-Band Material: 0.55-2.51? Min. Banding Thickness: 0.01? Max Banding Thickness: 0.39? Min. Panel Length: 5.51? Min. Panel Width: 1.96? 2 Feed Speeds: 39ft/min & 59ft/min Electrical: 230V, 60Hz, 3Phase Equipped With Siemens TD200

--at Auction, Seller Loading, Powered Inspection Available-- BIESSE AKRON 440 AX Edgebander, with Pre-Mill & Corner Rounding Specifications: - Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood. - Edge & Workpiece Capacity: 0.4 - 3 mm (0.016 - 0.12") Edge; 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5.5") min. panel length, and 85 mm (3.3") min. width. Working Units: - Pre-Milling Station: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blow-off device and SIKO digital counters for adjustments. - EVA Gluing Unit: Edge Feeding and Pressing Unit; Automatic loading of tape in rolls and strips; Quick change glue pot system. - Pressure Section: (1) Large 150 mm dia. driven & (5) idle pressure rollers. - Feed Speeds: Operating feed speeds 12 & 18 MPM (39 & 60 FPM). Workstations: - Double Motor End Trim; Tiltable from 0° - 15°, each motor 0.8 kW (1 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. - Top and Bottom Trimming; (2) Motors 0.65 KW (0.87 HP) each - "Pro-Nesting" copiers - Cutters R=2 mm. - Fine Trim/Corner Rounding Unit: (2) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edge banding up to 3 mm max. edge thickness. - Top & Bottom Flat Glue Scrapper, to remove potential glue squeeze-out. - Buffing Station: Top & Bottom, (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. Operator & Machine Control: - Operator control panel, "HDI" High-Definition touch screen control Windows XP based. - User-friendly graphic user interface with diagnostic and assisted maintenance. - USB and Ethernet port. 1.44 MB floppy drive, automatic or manual startup. Complete with: - High-frequency motors (200 HZ): Padded sound enclosure: - Top pressure beam with staggered double-row hold-down wheels mounted on ball bearings. NOTE: Includes new Glue Pot, extra knives & misc. parts.

Biesse Levia 310-1350 Sander

BIESSE ROVER B 4.35 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working capacity: "X" Axis is 125.9" (3,200 mm) any unit; "Y" axis is 51.7" (1,315 mm); "Z" axis stroke 6.3" (160 mm) max. material thickness is 5.9" (150 mm). -- Positioning Speed:"X" & "Y" Axis is 262 FPM (80 MPM) & "Z" axis is 66 FPM (20 MPM). -- Worktable:(6) Panel support rails with: (3) Vacuum pods per panel support; (4) pneumatic lifting bars for heavy panels.(2) Independent working areas with: (6) Front & (1 + 1) side pneumatic pop-up locating pins for positioning of parts on the worktable.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; each work zone with: (1) "Quick Connect" vacuum outlet for custom vacuum fixtures. -- Boring Unit:(1) 2.3 HP (1.7 kW) - 4,000 RPM Motor: (12) Independent vertical boring spindles with (6) spindles in "X" axis & (6) spindles in "Y" axis.(6) Horizontal spindles with: (2 + 2) in "X" Axis & (1 + 1) in "Y" axis; (1) "X" axis grooving saw for max. 120 mm dia. blade. -- Machining Unit:(1) 10.2 HP (7.5 kW) Vertically mounted HSD "Electrospindle" Router with ISO 30adapter, inverter driven 1,000 - 20,000 RPM with max. torque from 12,000 - 20,000 RPM.(1) 10-Position ride-along ATC for "on the fly" tool change. -- Operator & Machine Control:PC Front-End with: BIESSE "XP 600" + "BiesseWORKS Advanced" + Windows "WRT" (Windows Real Time) operating system; INTEL "Celeron" 2.0 GHz processor; 4 GB Hard drive.15" Color monitor, international keyboard, soft touch keypad & industrial mouse, RS-232 serial port, USB ports, CD ROM & 1.44 MB disk drives.Separate Control Panel with: Built-in 1,500 W air conditioner for constant temperature & dust-free environment; 11 KVA Stabilized autotransformer for voltages between 200 - 600 Volts. -- Complete with:(1) 100 cbm/Hr Vacuum Pump; centralized manual lubrication system for guides & ball screw; emergency stop rope; safety light barrier & sound absorbing protective head enclosure with debris curtain around bottom edge; scrap belt conveyor. -- Actual model is: BIESSE - ROVER B 4.35.

BIESSE ROVER 20 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working field: "X" Axis 113.9" (2,893 mm); "Y" axis 37.4" (950 mm); "Z" axis stroke is 3.9" (100 mm), max. panel thickness 2-1/2" (65 mm). -- Positioning Speed:"X" Axis at 246 FPM (75 MPM); "Y" axis 147 FPM (45 MPM); "Z" axis 49 FPM (15 MPM)."X" Axis moves on high precision prismatic guides and ground helical rack; "Y" & "Z" axis via hardened ground ball screw. -- Worktable:(6) Pneumatically locked & manually positioned panel supports with (2) vacuum cups each.(2) Working zones with: (6) Pneumatic backstops; (2) pneumatic side & (2) center stops; stops raised & lowered automatically by start/stop of machining cycle. -- Boring Unit:(1) 2.3 HP - 5,135 RPM Motor; (10) vertical spindles independently operated with (6) in "X" axis & (4) in "Y" axis.(6) Horizontal spindles: (2 +2) in "X" Axis & (1 + 1) in "Y" axis; 2-1/2" (65 mm) max. boring depth.(1) "X" Axis grooving saw with: 120 mm Dia. blade - 5,200 RPM. -- Machining: Equipped with: (1) 9 HP (6.6 kW) Air-cooled "Quick Change" electro spindle with ISO 30 adaptor.Router is driven by: 10.2 HP (7.5 kW) Inverter for variable speed from 1,000 - 24,000 RPM; RH & LH rotation.(1) 3-Position automatic tool changer mounted at the back of the machine for "on the fly" ATC. -- Operator & Machine Control: Separate Control Console with: CNi "NC 410" Operating System housed in air-conditioned cabinet.8" LCD Monitor: Displays programming graphics, numerical & function keyboard; 512 KB RAM memory; (1) "UPGRADED" USB drive.RS-422 Serial port for PC and RS-425 port for inverter connection; EPROM for machine data & subroutines; machine runs production programs while programming and editing. -- Complete with:Stabilized autotransformer for voltages between 200 - 600 Volt 50/60 Hz; (1) 100 cbm/Hr Vacuum Pump; triple photocell barrier; assortment of misc. parts and tooling; Users operator/maintenance manuals & backup disks. -- Actual Model is: BIESSE - ROVER 20.

BIESSE ROVER 18 CNC MACHINING CENTER: -- Specifications: Working capacity: "X" Axis 91" (2,310 mm); "Y" axis 24-3/4" (928 mm); "Z" axis stroke is 3-1/2" (90 mm); max material thickness 2-1/2" (65 mm). -- Worktable(6) Stationary Panel Supports with: (2) Vacuum cups each. -- Positioning Speed "X" & "Y" Axis 328 FPM (100 MPM); "Z" axis 27 FPM (90 MPM). -- Boring Unit2.3 HP Motor - 4,000 RPM with: (12) Independent Vertical spindles with (7) spindles in "X" axis & (5) spindles in "Y" axis; all spacing on 32 mm centers.(4) Horizontal spindles with: (2 + 2) in "X" axis for boring top & bottom edges of panels.(1) "X" Axis grooving saw for max 120 mm (4.7") dia. blade. -- Machining(1) 10 HP (7.5 kW) Router; variable speed from 12,000 - 18,000 RPM for RH or LH rotation with 7.5 kW inverter. -- Operator & Machine Control:CNI "NC 481" CNC 3-Axis Controller; built-in 9" amber CRT; 32 KB memory; 3-1/2" floppy disk drive.Tool correction, circular & helical interpolation, feed speed override, user-friendly programming, and background editing. -- Complete with: (1) 40 cbm/Hr Vacuum Pump; 20 KVA Stabilized autotransformer, side & rear safety fencing, safety photocell barrier. -- Actual Model is: BIESSE - ROVER 18.

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0ø - 15ø, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45ø precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. --Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17” flat screen (TFT) with high resolution

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 19 mm (0.118" - 0.75"), Panel thickness 10-60 MM (0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent units on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit: (2) 1.8 kW motors (2.5 HP), 12,000 RPM with NC controlled Auto-Set devices to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- Edge feeding: Gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt for quick heating & tank changing with floating & bi-directional glue roller applicator. -- Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0ø - 15ø, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45ø precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit: (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. --Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM.Features & Feed: -- All cutting & trimming workstations have HF motors and are enclosed by a padded sound enclosure, top pressure is provided by staggered double-row hold-down wheels mounted on ball bearings. -- Feed chain track speed: 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17” flat screen (TFT) with high resolution.Actual model is BIESSE AKRON 855

BIESSE EDGE - ROXYL 6.0 Edgebander, ...with (429) Hrs. Only!Specifications: -- Edgebanding thickness: 0.4 - 22 mm (0.02" - 0.87") Strip, 0.4 - 3 mm (0.02 - 0.12") Coil. -- Panel thickness 10 - 60 mm (0.39 - 2.36"), Min. panel width 85 mm (3.35"), min. panel length 140 mm (5.51"). -- Feed speeds: 10, 14, 18, & 20 MPM (33, 46, 59, & 65 FPM).Equipped with: -- "FI-502" Premilling Unit with: (2) Servo controlled spindles with Left-hand & Right-hand rotation & Auto-set device. -- "ADZ-700" Automatic anti-adhesive spray unit. -- 31" Dia. Coil table. -- Servo controlled infeed fence. -- Automatic edge Magazine for strips & coiled material. -- "VC-710" Hot melt glue system with: "QM-705" Premelt system for EVA. -- Servo controlled pressure section with: (1) Large driven roll & (4) idler rolls. -- PC-Based control with: 19" LCD Display, "ROXYL-MATIC" automated machine setup, MICROSOFT "WINDOWS" Operating System. -- 3-1/8” W Feed chain with: 3 kW (4 HP) Motor. -- Programmable top pressure beam with: Driven flat belt & 0.22 kW (1/3 HP) Motor. -- 19-1/2” Outboard support adjustment. -- Sound enclosure.Workstations: -- "IN-801" Front & rear end trim unit with 0° - 15° Bevel; pneumatic tilt & angle preselection from control. -- "RS-100" Top & Bottom rough/flush trim unit. -- "RF-400" Multifunction tilting Top & Bottom chamfering unit with: (2) HSD "ROTAX AT/MT 1073-120" 2.7 HP - 12,000 RPM Air-Cooled Electrospindles, (4) Servo motors: (2) For horizontal position & (2) for up/down position; Combination bevel/radius/flush insert knives, Pneumatic prepositioning of motors. -- "CR-202" 2-Motor Corner rounding unit. -- "RBK-503" Top & Bottom profile scraping unit with: 2-Axis Servo controlled knife positioning, 2 - 3 mm radius, for PVC edges; "RCC-701" Top & Bottom flat glue scraping unit with Pneumatic controlled in/out position. -- "SP-501" Top & Bottom buffing unit with: (2) 0.37 kW (1/2 HP) - 3,430 RPM Motors. -- STEINEL "3426" 2,000 W Hot air blowers.Complete with: -- Transformer.Dimensions of this specific machine with outboard support extended: 296" x 64" x 72" H.NOTE: Buy the TAYLOR "38A-M3" Return Conveyor (EXF# FR-010320) and keep the set together!

BIESSE STREAM B1 9.0 ... Production Edgebander with Pre-Milling & Corner Rounding Specifications: -- Capacity, 0.4 - 15 mm edge thickness cap., min. panel width 100 mm, panel thickness 10 - 60 mm, min. panel length 150 mm. -- Pre-Milling Unit: With jump control & side copying unit for managing warped panels, 2-position infeed fence, digitals readouts. -- NC 410 Controller with: Graphic interface on MS-Windows 2000 Professional, 32-bit operating system; high resolution LCD color screen, unlimited" number of working programs, each with functions for remote control of processing units; fault diagnostic, bar code reader adaptable; etc. -- Automatic (2) coil vertical feed magazine for coil material up to 3 mm thickness with automatic changeover. -- Patented Glue System w/pre-melt, large separated granular hopper for easy filling & high gluing capacity, with roller applicator (reversible); -- Pressure Section, (1) large driven pressure roller & (6) pneumatic secondary pressure rollers. Workstations: -- End Trimming:Double motor front & rear linear end trimming unit "IT 46" (0.4 HP/0.3 kW - 12,000 RPM motors ea.); pneumatic chamfer setting, 0° - 15° adjustable. --÷ Pre/Rough Trimming:Top & bottom "RS 10" (1.75 HP/1.3 kW - 12,000 RPM motor ea.), pneumatic exclusion & positioning from control panel. -- Radius/Bevel Trimming:Top & bottom (0.87 HP/0.65 kW - 12,000 RPM motor ea.), tiltable 0° - 30°, pneumatic exclusion from operator panel. -- Corner Rounding:4-Motor for leading & trailing edges. -- Profile Scraping Unit:Top & bottom with collection box. -- Flat Glue Scrapers:Top/bottom to remove potential glue squeeze-out. -- Buffing Unit:Top/bottom, ozcillating/tilting "SZ 30" w/pneumatic exclusion control from control panel & 0.67 HP/0.5 KW- 1,400 RPM motors; -- Hot Air Unit:Top/Bottom hot air blowers to reactivate/smooth heavy pvc radiused edges. Complete With:- Motorized top pressure beam with powered V-belt hold-down, electronic positioning by NC controller.- 80 mm wide Heavy Duty feed chain w/rubber pads, - 4 HP feed drive for feed variable speeds of 26 - 78 FPM. - Pneumatic Pre-set Stop System for most adjustments via the control panel on top & bottom trim, fine trim, and scraper station,- Electronic frequency inverter, electronic DC brakes on all trim motors.- Sound cabins for all trim work stations, outboard panel support.Note: Actual Model ... BIESSE STREAM B1 9.0

BIESSE - ARTECH LEVIA 330, ...3-Head Wide Belt Sander43" Width cap. Drum, Drum, and Combination Head.Head Configuration: -- 1st Head: Rubber covered Contact Roll, 6" dia., 25 HP motor. -- 2nd Head: Steel Contact Roll, 6" dia., 25 HP motor. -- 3rd Head: Combination head with a rubber-covered Contact Roll and Finishing Platen.NOTE: There are (2) 25 HP motors; one drives the 1st head and the 2nd drives the other (2) heads.Specifications: -- 44" x 85" Abrasive belts, electronic abrasive belt tracking; all contact rolls with pneumatic seclusion; Head #3 with air belt cleaner. -- EASY PRO "2000 C" Processor with (200) programs, touchscreen for control of Sander functions, thickness opening, feed speed, sequential startup, contact roll seclusion, and abrasive belt cleaner. -- Conveyor belt feed, 11 - 66 FPM variable feed speed, 2 HP feed drive with inverter control. -- 1/8" - 7-7/8" Motorized thickness adjustment with LED readout; automatic part thickness setup.Equipped with & Features; -- Automatic conveyor belt tracking. -- Infeed & outfeed shoes or rubber-covered holddown rolls, infeed panel "over thickness" sensor. -- Electronic brakes on both sanding head motors. -- Infeed emergency stop, 3-roll infeed extension, and motor load meter.

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Edge & Workpiece Capacity: 0.4 -15 mm (0.016" - 0.59"), Edge thickness, 14 - 65 mm (0.55" - 2.56"), Edge height, 10 - 60 mm (0.39" - 2.36"), Panel thickness:140 mm (5-1/2") Min. panel length, 85 mm (3.3") Min. panel width.Infeed Section: -- Pre-Milling Unit, "FI-701 Rectifies face to be edged before applying glue, Horizontal & vertical movement of (2) motors on linear guides, Independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) 12,000 RPM Motors, Independent copying pads on each unit, Auto-set device to ensure optimum positioning of cutters according to the thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit, "VC-710": with Automatic edge magazine for strip & coil stock, 3 mm (0.04") PVC Guillotine, "TEKNO-GLUE" System Includes: Pre-Melt, "QM-701", For quick heating & tank changing with floating & bidirectional glue roller applicator, and NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).Workstations: -- End (Edge) Trimming Unit, "IN-701-V": (2) 0.35 kW (1/2 HP) 12,000 RPM Motors, Automatic 4-position programmable chamfer from control panel (0°, 3.6°, 11°, 15°), Sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit: "RS-701": Top & bottom, (2) 0.8 kW (1 HP) 12,000 RPM Motors with Superimposed motor position, 1° Tilt capability. Includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit, "RI-701": (2) 0.65 kW (0.87 HP) 12,000 RPM Motors, For radius top & bottom fine trimming, Unit can be tilted 0° - 45°. Includes: NC axis multiple machining device. -- Corner Rounding Unit, "CR-200V": For corner rounding, top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") Maximum edge thickness. -- Edge Scraping Unit, "RB-701": For finishing rounded-off edges in PVC or ABS up to 5 mm (.20")thickness; Includes: Pneumatic unit lifter. -- Flat (Glue) Scraper, "RCC-700":Top & Bottom, removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700": Top & bottom. -- Hot Air Blower Unit, "PH-700", (2) STEINEL "2346" 2,000 W, Reactivates color of thick plastic.Complete with: -- PC-based control panel with 15" Color LCD monitor, HF (High-frequency motors on all cutting & trimming workstations. --Top pressure beam programmable via positioning motor, Top pressure provided by belt hold-down. -- 36" Diameter Coil table, Padded sound enclosure. -- Manuals (as pictured). -- Dimensions: 280" x 42" x 72" H. Weight: 3500 kG (7,750 Lbs).

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).

BIESSE LEVIA 320-1100 Wide Belt Sander, (2) Heads43" Width cap., Drum, Combination HeadHead Configuration:1st Head: Contact spiral grooved roll, 6" Dia., 30 HP motor.2nd Head: Combination head with a spiral grooved rubber-covered contact roll, 7-1/2" dia. 45 Shore covering, segmented platen computer controlled with air segments, 24 HP motor.Specifications: -- 43" X 74" Abrasive belts. -- Electronic abrasive belt tracking. -- All contact rolls with pneumatic seclusion, heads with air-jet abrasive belt cleaners. -- Output control of sectional platen. -- Conveyor belt feed, 11 - 66 FPM variable feed speed; Automatic conveyor belt tracking. -- 2 HP feed drive with inverter control. -- 1/8" - 7-7/8" Motorized thickness adjustment with LED readout.Equipped with & Features: -- Infeed and outfeed shoes or rubber-covered holddown rolls --Infeed panel "over-thickness" sensor. --Auto calibration, digital height read out -- Easy Quick grit selection. -- Electronic brakes on both sanding head motors. -- Infeed emergency stop. -- 3-Roll infeed extension and motor load metersNOTE: Some spec's may need to be verified