Wood Finishing For Sale

Stage #1 48” width 2 lights Stage #2 40” width 3 lights 220 volt singular phase

This listing is for a commercial grade heater that can be used for heating your facility or if outside air is ducted in can be an air make-up unit This is designed for inside installation. It was not originally used as air make up but in mild climates will be able to be used that way with duct work that needs to be built on site by a contractor. Foot print size of the unit is 46" x 46" Height 144 "Natural gasCFM 7,500BTUH input 400,000BTUH output 320,000Fan Type belt drivenHP (1) 2 HP fanFlue size 8" qty (1)Unit weight 1,250 lbs

Barberan UV Oven

BECCA - 25000: 22 Liters / 6 Gallon Cap.; 2.05 kW Fully Automated Solvent Recycling SystemSpecifications -- Processes: Conventional, alternative, & waterborne solvents. -- Boiler cap.: 6 Gallons; thermic oil cap.: 3.2 Gallons. -- Heating chamber size (approx.): 14"; Dia. x 14"; dia. -- Solvent recovery rate: > 90%. -- Operating temperature: 140° - 392° F. -- Operating Pressure: -0.223 - 1 Bar Absolute; -0.776 to 0 bar relative. -- Adjustable cycle time: 3 - 5 Hrs. Equipped with: -- Dual skin AISI 304 Stainless Steel heating chamber with: AISI 304 Stainless steel pressure relief lid; replaceable solvent-resistant thermal gasket seal. -- AISI 304 Stainless steel boiler with: Indirect thermic oil bath & (2) heating elements. -- Fan cooled copper condenser system with: Aluminum non-sparking fan blade. -- Temperature/Cycle time digital touchpad control with: LED Display; self-diagnostic system; liquid & oil temperature primary electronic & backup mechanical sensors.Complete with: Installation, Start-Up & Operator's Guides.

BINKS - COMET 3, ...Paint PumpMounted on a roll-around cart.

Infra Red heating unit designed to be used over a conveyor (not included). Currently set up to roll a shop cart under to assist us in some finishing processes. This is a two zone unit with an overall heating area of 56 sq ft. between the two infrared panels. Each section of infrared panels is 4'x7' allowing you an array of options to meet your needs. They do however, get controlled off the same control panel. --Unit has a mechanical percentage timer in control cabinet that is used to cycle power on and off as a means to control temperature. Controlling the distance from emitters to work surface is your other form of temperature control. The patented Black Body emitter consists of a serpentine configuration of NiChrome wire embedded in a refractory pad that is 12 inches square and approx.3/8" thick and coated with a high-emissivity black coating. -- Unit is complete and will need some retrofitting to meet your specific requirements.

48" wide Black Bros UV Curing Oven

BLACK BROTHERS - 22-D-875-56, ...Roller Coater56" Nominal length; 8-3/4" dia. applicator, Chrome doctor roll, upper elevator and top only. -- Setup to 0" - 6" thick. -- Smooth EPDM applicator rolls and Chrome doctor rolls. -- Variable feed speed drive, pass line height 34". -- Drip Pan, Feed Pan, Continuous Flow Trough to be Stainless Steel or Teflon Coated. -- Trough for continuous flow 1" pneumatic pump and hose to supply product.Complete With: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout and cleanup pan.

BLACK BROTHERS - 22-D-875-56, ...Roller Coater56" Nominal length; 8-3/4" dia. applicator, Chrome doctor roll, upper elevator & top only. -- Setup to 0" - 6" thick. -- Smooth Chrome applicator rolls and Chrome doctor rolls. -- Stationary feed speed drive, passline height 34". -- Drip Pan, Feed Pan, Continuous Flow Through. -- Trough for continuous flow 1" pneumatic pump and hose to supply product. -- (30) Day warranty for workmanship and manufacture's warranty for all parts used.Complete with: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout, and cleanup pan.

Manufacturer Specifications Width capacity 1300 mm Panel thickness: 3 - 80 mm variable feedspeed 6-30 m/min Coating roller 55° Shore with variable speed and scraper Chrome doctor roller with variable speed and scraper

BURKLE - Roll Coat, ...Lacquering Line with: UV Curing & HEESEMAN Sander. General Line Data:Working width: 1,300 mm (51")Working height: 900 mm +/- 20 mm (35 - 36")Production speed: 10 MPMPassing height 3 - 80 mm (3/16" - 3-1/4")Shortest length of boards 350 mm (14")Operating side: Right-hand side Electric:Operating voltage: 480 Volt, AC, 60 Cycles, 3-PhaseControl voltage 24 Volt, DC LINE CONFIGURATION:STATION #1 - 2-Roll Coating Machine - "SAS 1300" (Filling Machine) For single-sided application of base coating materials suitable for circulation. The machine is suited for base coating veneered, boardlike workpieces or solid components simultaneously filling fine grain or hairline cracks in the veneer by means of the Reversing Smoothing Roller. Application Unit:- Separate, infinitely adjustable frequency-controlled direct drive for the application roll. Rubber-covered application roll of double thickness of the rubber covering, with corrosion-resisting roller ends.- Quickchange coupling for the application roll with hinged bearings and an OLDHAM coupling. Oscillating scraper blade for the application and doctor rolls with an ergonomically designed scraper blade support is quickly removable for cleaning, and can easily be placed back by a self-locking worm gear.- Separate, infinitely adjustable frequency-controlled direct drive for the reversing Doctor Roller. - Change of rotation of the Forward Doctor Roll by an electric reversing switch in the Control Panel.- Hard chromium-plated doctor roll with a fine adjustment by a worm gear gap adjustment via a mechanical digital indicator in the handwheel.- Hood, which can easily be opened, features integrated radiation protection. Smoothing Unit: - Hard chromium plated smoothing roll with an infinitely adjustable, frequency-controlled direct drive. - Scraper blade for the smoothing roll with an exchangeable plastic blade. - Distance from the smoothing roll to the application roll approx. 0.5 mm, for the automatic return of the material, readjustable when regrinding the application roll. Material Circulation System:- Pneumatic double diaphragm pump (R 1“) with pressure reducing valve & stop for careful lacquer feed, particularly suited for very viscous and solvent-free lacquer systems.- Material supply by means of a chemical resistant hose and special steel pipe, ergonomically designed and fitted underneath the hood, with discharge hose and stop.- Large-dimensioned lateral collecting troughs and return gutter made of special steel.- Spring-loaded end plates with exchangeable screwed-on plastic coverings.- Suitable for one way containers of 30 liters contents (max. height 400 mm). Motorized Height Adjustment:- (2) Separate, motorized precision lifting gears wit

This machine was customized to be a wire brush machine for a floor finishing line.

BURKLE - VBM 1688, ...Stain Wiping MachineSingle sided machine, 1,600 mm wide; 2-Brush Panel Cleaner (TAMPICO brushes). Features: &#9679 Heads can be positioned as needed spacing between the brushes by sliding brackets. &#9679 Brush raising & lowering accomplished by means of handwheel adjustment. &#9679 Brushes are removed at side of machine by sliding out of shroud/channel support rail. &#9679 Safety bar checks part thickness for overthickness parts. &#9679 SIEMENS Control to set rotation speeds & feed belt speed. &#9679 Rigid Aluminum bolted base construction. &#9679 Solid feed belt (NO vacuum holddown)

Cameron Automation Flooring Nesting Line Buffer Table for making 2'-10' flooring into nested bundles. Makes a new bundle every 30 seconds. Feeds from right to left

Maximum workpiece height mm. 320 Maximum workpiece width mm. 320 Minimum workpiece length mm 700 Brush diameter mm. 160 Brush rotation adjustable with inverter rpm 0 – 1400 Blower motor power under inverter kw 4 Brush motor power under inverter nr. 4 x kw 0,55 Work speed adjustable with inverter mt/1’ 8 - 45 Feeding motor power kw 1,1 Electrical system MACHINE DIMENIONS: Volt 380± 5% Lenght mm 3350 Width mm 1350 Height mm 2350 Machine weight kg 1150

CEFLA - MITO, ...Complete Spraying System with SORBINI Cleaning Brush.Reciprocating Feed Through System for Waterborne & Solvent-Borne Coatings: The max. flexibility and technology for the continuous spraying of any kind of raised panels.Features: -- Machine designed with a solid structure: LASER 3D; full accessibility, thanks to the wide use of glass superficies, access doors, and extractable parts. -- Conveying System with: CFB Belt with sealed edge, driven by inverter. -- Axis driven by the powerful brushless motor and by a sophisticated toothed belt handling system, with recycling sphere bearings. The best performances in speed, acceleration, and the softness in guns motion allows to achieve the max. application quality. -- The central axis holds: (1) Gun supporting arm (removable), equipped with quick-release (predisposed for max. 4 guns); complete with: Manual height adjustment, (3) high pressure lacquer feeding circuits with recycle; lacquer filters with stainless steel fittings. -- Exclusive pressurization flows analysis and sophisticated air diffusion plenum with double fan for air intake and filtration results in: Higher lacquer saving, better machine cleaning. Circulation provided by floor mounted MZ RLQ 560, Direct-drive 4 KW , 1755 RPM motor. -- Tanks with supporting areas for filters by COLUMBUS or ANDREAS-type filters.Electronic Scanner for: Shape reading and workpieces positioning; max. efficiency in managing the guns' spraying.TECHNICAL FEATURES:Total length of the machine: 4,650 mmTotal width of the machine: 3,850 mm (4,210 mm with fan)Machine structure height: 2,500 mmElectronic control unit with: PLC and software for machine managing.Main control cabinet: Pressurized, placed at the machine infeed, along the service side complete of cable and wiring system for connection to all the users.Spraying parameters management is operated by PLC:Working programs setup, measurements of the lacquered surface & lacquer consumption, 5" color touchscreen display for diagnostic and control; possibility to exchange data from and to PLC managing complete Lines.Possibility to manage pumps for color change/washing (up to 4 pumps). -- Comes with: 2006 SORBINI/CEFLA VS/33-ACT-F, 460/3/60 Panel Cleaning Brush with brush for the top roll followed by a nozzle blow off station. (1) Head, 53" width cap. Top brush head; features timed rotating air blowers, air liner blower with nozzles. Upper mounted Anti-static ionization bar; 400 RPM brush speed.With CEFLA TM 3000, 600/3/60 V, infeed belt conveyor. -- Line is disconnected/dismantled per last (8) photos.

Cefla and Delle Vedove Finishing Line

CEFLA EASY 2000D Reciprocating Feed Through Sprayer and Vertical Oven Finishing Line:This line is still in operation with the original owners, it have never run full time, there are weeks when it is 1 day per week. It is recommended with a line of this age to do a full recondition prior to or as it is being installed. If that is not possible, it is still running and can be seen that way. CEFLA Complete 52" (1,300 mm) Finishing Line with: SORBINI Panel Cleaner, "EASY D 2000 W" Reciprocating Sprayer, Conveyor(s), and CEFLA Hot Water Vertical Oven. The line is composed of the following:001) Belt conveyor CEFLA "TN 2500"002) Panel cleaning / brushing machine SORBINI "VS 33"003) Automatic spraying machine CEFLA "EASY 2000 DRY SYSTEM" with pressurized cabin004) Transfer conveyor005) CEFLA PIEFFE PF2 VL/6 7500 pass through oven006) Vertical Oven, (3) chambers with belts CEFLA "VN 2000"007) Unloading Conveyors

Cefla Rotostain 2000

Cefla Sorbini T/20-3-STP Triple Head Print & UV Line (3) Print Head System (2) IR Ovens Available Immediately