Sawmill Equipment For Sale

WEG Soft Start, SSW07 type Soft Start, To be cut 6" above and below

WEG GPH2030QC4000 Soft Start, 15hp, SSW07 Type

WEG WWE-361-BP Starter, 250 hp, To be cut 6" of motor (2) Available

WEG GPH2100QC4000 Soft Start, 100 hp , SSW07 type Soft Start, To be Cut 6" Above and Below (3) Available

250HP, 460VOLT, 1800RPM, EITHER 447T or 445T FRAME, TEFC, INVERTER DUTY, PREMIUM ENERGY EFFICIENT. This motor never ran on the equipment that it was mounded too.

WEG Motor, 100hp, 1790/1490 Rpm, 230/400, 200/400,405T Frame

WEIL-MCLAIN, MODEL 988, steam or hot water boiler. Used in school system approximately 7 years. Good condition. Price includes:  7 sections of cast-iron plates and enclosure with controls. #2 fuel oil fired burner. Technician who removed system and put in a different system available to discuss.  Offered as-is, as removed from service. Price $8,500.00 OBO

2020 Weima WLH 600 Grinder 50 HP motor Vibrating Infeed

2008 Weima WL 6/18.5 V-Rotor Drop Feed Wood Grinder Machine number 500-8876 460V 3 Phase 60 Hz Motor Output- main drive 18.5 KW 1760 rpm Motor Output- hydraulic system 1.5/2.0 KW 21 tools Rotor speed ca.90 Rotor diameter 252 mm Includes spare rotor

WEIMA Grinder - 2004 Model WLK 13/75 Low Speed, Hopper Style Grinder. Batch style grinder with 75 HP low-speed rotor, top feed hopper, self-contained hydraulic system with hydraulic ram, and controls. Controls operate the ram, which forces material against the low-speed rotor. Controls vary the hydraulic pressure based on the load on the rotor motor. Features reversible carbide cutters on a large diameter rotor, a 2 cubic yard hopper with a 51 x 47 inch top opening. Weighs about 10,000 lbs. Serial 500-6283.

Weima WLB 1300 Horizontal Grinder 50 HP Motor System works, not currently in use, will need main bearing replaced.

WEINIG - Rondamat 934, ...Profile Knife GrinderSpecifications: -- 9-3/8" Max. arbor length, 4" - 9" tool dia. -- 6" - 8-7/8" Grinding wheel dia., grinding wheel speed inverter controlled with grinding wheel speeds 1,500 to 3,000 RPM; 1.1 kW (1.5 HP) Motor.Equipped with: -- Hydro-clamping of grinding wheel to arbor. -- Tool carriage movement with precision linear table bearings; setting gauges for axial constant; axial (side) clearance angle 0° - 20°. -- Onboard diamond wheel dressing, 13-Gallon Coolant tank with 1.2 HP Pump.Dimensions: 50" x 43" x 62" HWeight: 1,600 Lbs

WEINIG RONDAMAT R960 Profile Grinder Working Dimensions: -- 9-29/64" maximum tool width; 3-15/16" Minimum to 11-13/16" Maximum cutting circle. -- Grinding Wheel: Diameter 5-29/32" min to 8-7/8" max. grinding wheel bore - 60 mm. Onboard diamond wheel dressing tool. -- Drive: Variable Frequency Controlled Drive giving a spindle speed - 1,500 to 3000 RPM; 1.5 HP Motor. -- Template carrier: Utilizes a template stylus-copy system, whereby the tool head table copying-grinding is effortless (precision linear floating table movement feels smooth as if there is zero gravity). Resistance template cross support with setting gauges for axial constant system; axial (side) clearance angle 0° - 20°. Holder for fixed and revolving tracing pins; for easy follow of the template to grinding aggregate. -- Coolant: 13 Gallon coolant tank capacity with 1.2 HP coolant pump. -- Includes: Manuals and 1-13/16" arbor.

WEINIG RONDAMAT R960 Profile Grinder. Working Dimensions: -- 9-29/64" maximum tool width; 3-15/16" Minimum to 11-13/16" Maximum cutting circle. -- Grinding Wheel: Diameter 5-29/32" min to 8-7/8" max. grinding wheel bore - 60 mm. Onboard diamond wheel dressing tool. -- Drive: Variable Frequency Controlled Drive giving a spindle speed - 1,500 to 3000 RPM; 1.5 HP Motor. -- Template carrier: Utilizes a template stylus-copy system, whereby the tool head table copying-grinding is effortless (precision linear floating table movement feels smooth as if there is zero gravity). Resistance template cross support with setting gauges for axial constant system; axial (side) clearance angle 0° - 20°. Holder for fixed and revolving tracing pins; for easy follow of the template to grinding aggregate. -- Coolant: 13 Gallon coolant tank capacity with 1.2 HP coolant pump. -- Includes: Manuals and 1-13/16" arbor.

WEINIG R 960 Profile Grinder 12"12" Max. arbor length, tool dia. 9" max. to 4" min. -- Grinding wheel speed inverter controlled 1,500 to 3,000 RPM by 1.5 HP motor. -- Hydro-clamping of grinding wheel to arbor. -- Tool carriage movement with precision linear table bearings, setting gauges for axial constant, axial (side) clearance angle 0ø - 20ø. -- Onboard diamond wheel dressing, 8-7/8" max. 6" min. grinding wheel dia.; 13-gal. coolant tank with 1.2 HP pump. Includes -- arbor dia. 1- 13/16".Note: New bearings on carriage

WEINIG RONDAMAT R960 Profile Grinder. Working Dimensions: -- 9-29/64" Maximum tool width; 3-15/16" Minimum to 11-13/16" Maximum cutting circle. -- Grinding Wheel: Diameter 5-29/32" min. to 8-7/8" max. grinding wheel bore - 60 mm. Onboard diamond wheel dressing tool. -- Drive: Variable Frequency Controlled Drive giving a spindle speed - 1,500 to 3000 RPM; 1.5 HP Motor. -- Template carrier: Utilizes a template stylus-copy system, whereby the tool head table copying-grinding is effortless (precision linear floating table movement feels smooth as if there is zero gravity).Resistance template cross support with setting gauges for axial constant system; axial (side) clearance angle 0° - 20°. Holder for fixed and revolving tracing pins; for easy follow of the template to grinding aggregate. -- Coolant: 13-Gallon coolant tank capacity with 1.2 HP coolant pump. Includes: -- 1-13/16" arbor

WEINIG RONDAMAT 934 Profile Grinder: -- 9" Arbor length, 11-1/2" max. tool dia., 1.5 HP motor, tilting head assembly for back relief grinding, clearance angle on peripheral of tools 10° - 30° and to each side 0° - 20°. -- Variable feed speed 1,800 - 3,000 rpm via a vari-speed gearbox, on-board wheel dressing, 9" max. wheel dia.; 0.16 HP coolant pump with built-in coolant tank. -- Includes: Operators manual, clamping nut, and pull-off bolt, 1-1/2" arbor, and an extra set of grinding wheels and toolingWEINIG OCMS measuring stand -- With a working width of 300 mm. -- The allowable tool dimension of 3" to 11-3/4" head diameter. The measuring stand allows for electronic measuring and indicating of cutter head dimensions with electronic digital readouts; visually establishing the tool measurement, no setting errors, and no expensive CNC control. -- Magnifier screen viewer with 20:1 magnification; the cutterhead is placed in Powerlock tool post, all the operator does is view the scope and move the measuring carriage via precision dialing left to right. -- Measured values (radial) and (axial), tool dimensions both minimum and maximum are displayed. -- Includes: 1-1/2" arbor.

Weinig R950 Profile Grinder

Weinig Profile Sharpener

Weinig R-930 Profile Grinder Mach. No 820/299