Meadows Mills For Sale

3 phase, 110V, will grind 24" - 30", will do alternate bevel, good condition

Nielson Model 800

NORDFAB NFK Series Modular Dust Collector with (8) Modules, reverse air cleaning and drag chain unloading into a Rotary Air Lock (RAL) --23,000 CFM approx. capacity based on filter area and desired Air to Clothe Ratio. With 50 HP. Consisting of (248) filter bags of 8.7" dia. x 77.2 " long(220 mm x 1,960 mm long) also (8) filter bags of 8.7" dia. x 54.1" long.(220 mm x 1,375 mm long) - located at cleaning fans - for a total of 3,680 sq. ft. of filter area. -- Consists (8) modules and (1) inlet blank module. Fan inlet approx 26" dia. -- Bottom conveyor chain with scrapers carrying the dust to one end and fed into the RAL -- Includes NRS-10 Rotary Air Lock and Transfer Blower to convey the dust to an enclosed waste container (not included). -- Electrical control panel with starters included. -- Overall dimensions 32' long x 7.5' depth x 13.5' high (without support steel)., Approx weight 10,000 lbs. --Actual model is NFK 8AJ/1BL

Nordfab Air Blower with 40HP Motor

Northern Automation Lumber Stacker with Lift Table. 3 phase. 36"-192" capacity. #C935

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

Northtech horizontal band resaw, (2) blades, will cut up to a 12 x 12" cant, powered by (2) 20 HP 460 Volt 3 Phase motors, runs (2) 1 1/4" band blades, Excellent Condition, (new condition with less than 4 hours use). Owner is retiring. Ref# 119, Contact Amy (928) 723-9449

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

Norwood LumberPro HD36 23hp (627cc) B&S V-Twin OHV electric start gas engine , 4 ft. bed extension for 16 ft. total , log rolling ramp, auto dog assist. Used as hobby mill - low hours. Includes any new blades available jack stands for levelling Stationary now but can easily converted to mobile.From Mgf.

(2) Unassembled front load Kilns only System with high HP heat and exhaust designed to hold 8,461 bd/ft (20 cub.m) of 3/4" (25 mm) lumber and 10,475 bd/ft (25 cub.m) of 8/4" (50 mm) lumber (35 cbm). -- Kilns internal dimension: Height 12'3-1/2" (3.75 m), Depth 16' (4.88 m), Width 21' (6.4 m). -- Loading door opening of 10' (3.05 m) x 21' (6.4 m); 1/8" aluminum side wall bumpers, side hinged doors, exterior installation. -- High HP will service the heat requirements up to 245k BTU/Hr. -- Electrical requirement of 230 VAC, 3-Phase, 60 Cy; 7.21 kW/Hr. -- System includes: Timber Dry management automated Dry Kiln Controls for each kiln, touch-screen operator interface, data recording, optional remote access, and networking capability, Replacement part kit for a kiln. Manuals & Blueprints

Unassembled Front Load Kiln with Standard Heat and Exhaust -- Interior dimensions: H 17' 6" (5.33 m), D 25' 8" (7.8 m), W 26' (7.9 m). -- Loading Door Opening: height 14'6" (4.4 m), width 25'3" (7.7 m). 1/8" Aluminum Bumper Walls, Top Hinge Door, Exterior Installation. -- Average 4/4 capacity: 25,459 Bd Ft. with 3/4" stickers. Average 8/4 capacity: 33,293 Bd Ft with 3/4" stickers. -- Price shown is for kiln only. -- Standard HP Heat requirement: 382k BTU suitable for drying dark hard woods; Optional high HP Heat requirement: 674k BTU suitable for drying softwood and white hardwoods. -- Electrical requirements: 480 VAC, 3 Ph., 60 Cy; 16.5 kW/Hr. Timber Management Control System with touch screen operator interface, data recording, remote access & networking capability. -- Features: Control room with heated air intake; 12'H x 4'D x 26'W. Top Hinge door opening System includes "230" electric chain hoist. Boiler Room: 12' W x 25' D x 17'6" H. 10' roll up & (1) access door. - Timber Dry Management Network Capability.

Nova Dry Kiln 26’ wide x 25’ deep holds 5500-12000 board feet propane or Natural Gas fired

NOVA TTF-6200 Dry Kiln System; Unassembled Front Load Kiln Designed to hold 5,100 bd. ft 4/4 Lumber, or 6,120 bd. ft 8/4 Lumber, Using 3/8" (9 mm) stickers. -- Specifications: Interior Dimensions: H 10' 3,5" (3.14 m), D 7'2"(2.19 m), W 25' 3" (7.7 m). -- Loading Door Opening: H 9' 10" (2.85 m), W 25' 3" (7.7 m). 1/8 " Aluminum sidewall bumpers, side hinged doors, exterior installation. -- Average 4/4 capacity: 5,100 bd. ft (12 m3) with 3/8" (9 mm) stickers. -- Average 8/4 capacity: 6,120 bd. ft (14 m³) with 3/8" (9 mm) stickers. -- Price shown is for kiln only. -- High horsepower heat requirement: 128 k BTU/hour. -- Heated Floor System, manuals and blueprints. -- Electrical Requirements: 230 VAC, 1 Phase, 60 Cycle, 25 kw/Hr max.

2023 Nyle L200M Kiln 220V Single Phase 4 Fans Very Good Condition Kiln Unit Dimensions (H x L x W) 37” x 32 1/2” x 20 1/2”

Nyle Firewood Dry kiln No chamber included

OGAM Gang Rip 30HP Motor w/electrical still Hooked Up, Model PO 195, S/N 15149

Oliver Sawmill New Carriage Wheels New battery

1990 Onon Cummins MDL 500DFFB 39955F S/N J900356550 3 Phase 500 KW Genset

7.5 HP single phase cyclone/dust collection assorted dust pipe and fittings as pictured

ONEIDA AIR SYSTEMS FXK041500 Cyclone Dust Collector w/ After-Filter Plenum: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,000 CFM @ 2.7" SP with 15 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Izumi Axtar Spunbond Media cartridge after-filters (hanging) for 620 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- Inlet size 14" round. outlet 16" round dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, internal silencer reduces sound to 85-87 dB @ 10'Includes Rotary Air-lock for dumping into a waste bin!MADE IN THE USA.