Sawmill Equipment For Sale

PalletPal Spring Lift Table Specifications Load capacity 400 to 4500 lbs., depending on springs Load size .......50" wide x 50" long x 72" high (max.) Length 45 1/4 inches Width (base frame) 36 3/4 inches Compressed height 9 1/2 inches Extended height 27 3/4 inches Rotating ring, outside diameter 43 5/8 inches Rotating ring, inside diameter 40 5/8 inches Adjustment for sloping floors Can adjust for floor slope up to 1:25 using optional adjustable feet 4 Available

SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

Speedaire Air Compressor 5 hp

Sprecher & Schuh starter

Sprout Waldron Mdl 2548 Hog with 200HP Motor

Sprout-Bauer Hammer Mill 38-12.4 H-Mill S/N 88-1530 W/ 100HP Electric Motor.

Sprout-Bauer Hammer Mill Model 38-12 H.M. - S/N 90-0269 W/100HP Electric Motor

Sprout- Waldron shaker screener, was running when pulled out of production.

(3) Square D Model 6 Motor Control Centers 600A Horizontal, 300A Vertical, 600 VAC Max; Includes: (1) Square D Size 3 Nema Starter, 600V, 50/60 Hz; (1) Mag-Gard Circuit Breaker Cat No. FHP3610018M, 100A, 600V; (1) Mag-Gard Circuit Protector Cat No. FHP3605016M, 50A, 600V; (1) Square D Size 2 Nema Starter, 600V, 50/60 Hz; (1) Mag-Gard Circuit Breaker Cat No. FHP3610018M, 100A, 600V; (1) Square D Size 3 Nema Starter, 600V, 50/60 Hz; (1) Mag-Gard Cirucit Protector Cat No. FHP3610018M, 100A, 600V; (1) Square D Nema Starter, 600V, 50/60 Hz; (1) Powerpact Circuit Breaker Cat No. HJL36030M71, 30A, 600V; (1) Square D Size 1 Nema Starter, 600V, 50/60 Hz; (1) Powerpact Circuit Breaker Cat No. HJL36050M72, 50A, 600V; (1) Square D Size 2 Nema Starter, 600V, 50/60 Hz; Tag: 251818

Square D Panelboard Part No. 1217013939003001, 150A, 208Y/ 120V, 3PH, Enclosure Type 1 NQOD; Includes: (34) Square D 20A Breakers; (2) Square D 30A Breakers; Tag: 246938

Square D 800 Amp Motor Control Center w/ 1-600 Amp; 1-200 Amp; 1-60 Amp; 1-25 Amp breakers 480Y/277 V 60 hz

Square D Sorgel 3 phase general purpose transformer kVA 45

Square D Altivar 58 TRX 300 hp starter

Square D Mod 6 Motor Control Center Bus Rating 600AMP Horz & 600AMP Vertical

Altistart 46 soft start w/no disconnect

SQUARE D - 75T3H: 75 KVA; 480 - 208 V; 3-Phase Autotransformer Specifications: -- Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 2. -- Multi-Tap (432 - 504 V) Primary 480 V (Delta); Secondary 208Y / 120 V @ 60 Hz ventilated. -- Aluminum windings. -- UL Listed. (2) Available; price per unit. - Make offer for both!

2000 Staiger V29 Slow Speed Grinder Hog, 30HP Electric Motor S/N 200420

STAR V MACHINERY - SCG-1600: Automatic Cross Groover -- Specifications(1) Spindle with: 12 HP - 3,600 RPM Motor; 60" max. crosscut cap.; material thickness: 0.25" - 1.125".(1) Internal 60" stroke Tape Applicator Station. -- 96" Stroke Servo motor driven Rear Pusher Fence (full 60" rear table width); 96" long x 20" front table with: (5) Digital manual stops. -- Rear Fence Movement, Cutter forward Speed Cut/Tape Stroke and All Controls for Start/Stop, On/Off, Axis position Displays on 10" Touch Screen Panel HMI. -- Grooving head up & down movement via pneumatic cylinder with: Linear rail & linear bearings; depth fine adjustment with special threaded adjustable unit. -- Carriage cross travel powered by: 3 HP Hydraulic motor (4 GPM); driven ball screw with: Linear rail & linear bearings; feed rate: 0 - 40 FPM; Heavy-Duty welded frame construction. -- Complete with:Safety guards & cutter guards; pneumatic support fence; (1) Heavy-Duty infeed/outfeed roller tables. Available options at additional cost below:Accessories, Tooling & Tape: Choose and add to machine base price. Cove Corner Plug Jig: ...$ 575 ea. Brazed carbide 90° cutter for up to 1/2" solid surface: ...$ 745. Please specify the material. Brazed carbide cove backsplash cutter for 1/2" solid surface: ...$1,265 ea. Please specify 3/8" or 1/2" radius. Brazed carbide 90° cutter for up to 3/4" wood materials: ...$ 940.00. 90° Insert cutter for up to 1/2" thick material (body only): ...$1,265.00. Requires below inserts.......90° V-Insert for up to 1/2" thick material: ...$32 ea. min. of (12) inserts required: ...$ 384.......Carbide insert cove backsplash cutter head for 1/2" material (body only): ...$1,590 ea. Please specify 3/8 or 1/2 Radius.Requires Below Inserts:......3/8" Cove radius insert for 1/2" thick material: $42 ea. Min. of (12) inserts required. ...$ 504. ......3/8" Double 45° insert for 1/2" thick material: $42 ea. Min. of (12) Inserts required. ...$ 504.......PCD Diamond 90° cutter for up to 1/2" thick material $3,485 ea.......PCD Diamond cove cutter with 1/2" radius for 1/2" thick material: $ 5,645.00 ea. Roll of VAC2MG: 2" (50 mm) wide; 1,025 y (937 m) long roll V-Groove tape: $ 245. ea.& Minimum of (3) rolls per order = $735. -- Actual Model: STAR V MACHINERY - SCG-1600: Automatic Cross Groover

STAR V MACHINERY SLW-6018 SLAT WALL GROOVING MACHINE: -- Specifications60" (5') Wide panel capacity, feed through style overhead milling Slatwall machine. The machine will produce 5' x 8' panels in portrait orientation or any orientation as long as the panel size does not exceed 5' x 5'.The panels are placed with side to be grooved, facing up, then pushed in between the fixed fence and a movable fence, until the panel is grabbed by the first rubberized feed roller, the panel is then transported between a number of pinch rollers and processed through 3 rows of high-speed spindle motors.As the T Slot cutting is processed each bank (6 in total) of 3 high speed spindle motors cut a T shaped groove appropriate to the size of tool installed in each spindle, blow the groove clean by use of high-speed air knives, and remove dust through a number of dust ports. Then pinch rollers push the sheet out of the machine roller bed.Panels as narrow as 6" wide can be fed through the machine although workpieces less than 3/8" thick must be 48" wide. Workpieces as short as 24" can also be fed through the machine safely.Minimum recommended workpiece width, 6": Maximum workpiece width, 48": Minimum recommended workpiece length, 24": Maximum workpiece length, UNLIMITED: Maximum workpiece height, 1.5". -- Features:5HP 1750RPM, 460V Feeder Drive Motor through 50:1 Gear Box. 5HP VFD Inverter to drive and control feed speed through machine, 0-50 linear feet per minute. Heavy Duty Welded Tubular Steel Frame Construction. Stainless Steel Roller Bed with Rollers 6" on Center. 10x Linatex Rubber coated Feed Pinch Rollers Driven by 5Hp Feed Motor and Drive. Fixed Guide Fence & Movable fence to aid feeding of sheets into machine. Safety Fence around both sides along the length of the machine, with 1 gate in each side, each with safety interlock. Safety photo eye in infeed and outfeed side of the machine. Gauge block for setting height of router arbors. -- Spindle Motors:18 x 3 kW (4 HP), 18,000 RPM, 230V, High Speed Spindle Motors. 100 HP VFD Inverter to drive and control rotational speed of all 18 spindle motors.Variable RPM of Spindle Motors through Potentiometer and RPM displayed on Control Panel. Individual Ammeter for each Spindle on Control Panel. 6x banks with 3x High Speed Spindle Motors per bank (18 Total Spindle Motors). All 6 Spindle Banks are adjustable on the Overhead Beams by Hand, and lock into Position via locking handles. Digital Read Out for horizontal position of each spindle bank. Spindle 1 on each bank is fixed horizontally, Spindles 2, and 3 adjust on each bank horizontally. All 3 spindles adjust individually vertically on each spindle bank via Hand wheel. Position of depth on Digital Read Out.All Spindle raised individually through pneumatic cylinder for changing tooling, or when not in use. Each Bank has a phenolic Hold Down Shoe.Spindle Centers adjust from 3" to 4" Centers; Rapid Center Adjust Switch, from 3" to 4" through Air Cylinders against positi