Sawmill Equipment For Sale

Hemco Stacker Cyc

11' x 80' Collector Deck Electric Drive

Henke 5HP Piston Air Compressor w/ Tank

HewSaw SL250 Trio sawing line from 2005 This line has already been dismantled and loaded into containers. It is ready to ship! - Consists of log positioning devices, conveyors and three sawing machines. HewSaw sawing line is designed to process logs ranging from 100 mm – 420 mm small end diameter, to 550 mm large end diameter, with length 2.4 - 6.2 m - Feeding speed of the sawing line can be adjusted from 50 m/min to 150 m/min. Top diameter: 100–420 mm Maximum log diameter: 550 mm Cant height in Chipper Canter: 75–410 mm Cant width in Chipper Canter: 75–410 mm Cant height in Rip Saw: 63–310 mm Cant width in Rip Saw: 75–410 mm Saw kerf: 4.2–5.0 mm Chip length: 20–30 mm Sawline 1. Measuring conveyor 2. Log scanner 3. Log positioner 4. Chipper canter 5. Cant scanning conveyor 6. Cant scanner 7. Cant saw 8. Seperating conveyor EK2 9. Cross conveyor 10. Belt conveyor 11. Cant turner 12. Infeed conveyor 13. Rip saw 14. Belt conveyor 15. Belt conveyors under machines, for waste handling 16. All electric boxes

Hi-Tech Chipping Edger

Hi-Tech Chipping Edger

23' Hi-Tech Scanner with Dyna Vision Lazers & Allen Bradley 1200P Control Console.

High Tech 20' Trim Saw (10) Blades

Hildebrand

Conveyor system with automatic sensors.. approximately 600-800 ft with all motors and accessories..

chain type log turner, sized for 40" carriage, hyd drive, good working condition

This mill is ready to be removed from the current location. - 4 Roll Cases 24’’ 2 center 6.5 Diameter 45’ 56’ 62’ 70’HMC All motor controls included - 7 Lumber Decks Flat Chains 10’ 12’ 16’ 20’ 24’ 40’ 82’ 5 Chains WIDC All motor controls included - 2 Log Decks - 28’ Long 12’wide 3 chains stop loader - 14’ long 12’ wide 4 chains stop loader - All motor controls included - Newman Trimmer, drop saws, scrap belt chain 100’x 24’ - Unscrambler 16’wide x 5’high 8 chains - Air Compressor Model SSREP100 HP - Air Dryer storage tank - HMC Model mm10 4 heah block carriage 49’ - HMC Saw Booth - HMC Feed Works - HMC Husk 54’ bottom saw 36’ top saw - 200 HP motor - HMC Log Turner - HMC Drop Belt Live Off Barrer - 10 Headrig saws inserted tooth 54” - Roof Top Chain 10ft 5 Chain - Blower system - Tie-Cant Deck 62’Lx13’ W 4 chain all motors & Controls - Roof Top Lumber Deck 30’L x 13’W 5 chains all motors & Controls

Rosser head, slant track, hyd. drive on the head, in working condition, CALL FOR REBUILDING OPTIONS ON THIS MACHINE

rosser head style, all hyd. drive, 36" dia. log capacity x 12' long, very good condition

HMC Carriage 5x10 Cab with controls System is already removed from service and ready to load. Notes from seller: Carriage is 17'1" longKnee spacing is 63" from 1 to 2 78" from 2 to 3 1 to 3 is 141 1/4" Carriage frame is 76 1/2 " wide Track centers are 62" Track rails are worn out. We used the old track frame for our new carriage

HMC 2-Saw Trimmer Model ET-10,;Complete with the following features: --16′ capacity. --Push Button Setworks. --Left hand (feeds from left to right). --Cuts up to 8″ thick. --Belt Conveyor for waste.NOTE: Removed from service and it was running just fine at the time of removal. Stored outside.

HMC MDS-50 Left Hand Drop Saw Trimmer For trimming Boards, Cants, or Ties up to 8" thick and will pass 10" Material. Feed Chains are 81X chain driven by a 3HP Variable Speed Motor with hold downs, each 24" saw is belt driven by 10 HP motors, starters, and fuses are mounted to the Machine in a Nema 12 Enclosure. 0',2',8',10',12',14', and 16' saw units, set up to pass 20' long material. Automatic length trimming with manual override is controlled by programmable control, powered even-ender rolls with a 2 hp drive, and includes one stationary stop gate. Front, back, and top guards are included, and an Automatic shutdown if a door is open while the machine is running. Includes spacers to raise the machine. 360/440 volt

HMC 2 Saw Vertical Edger 30HP Motor

HMC Model; 1DC, AC carriage drive, complete unit ready to work