Stationary Wood Chippers For Sale

2014 Peterson 4300B -6,000 frame hours -Current hours on engine and rebuild 100(C18) -New rods and mains -New turbos -New pumps -Valves -Infeed floor and chains -6 new knives -New fans -Wiring -Tires are 90% brakes work

PETERSON PACIFIC 5000G Whole Tree ChipperSpecifications: -- Engine: CAT 3412E 1000 HP Diesel Engine -- 3-Flail, Key Knife system currently set for 5/8 chip sizeRecent rebuild on machine: -- Overhung load adapters both replaced within 1000 hrs -- Fan pump replaced within 1500 hrs -- Swing/ boom pump replaced within 750 hrs -- Stick boom pump replaced within 100 hrs -- Engine computer less than 750 hours -- High pressure fuel pump less than 750 hours -- New radiator last summer -- Update main boom pump & flow divider last fall -- Installed a new seat 2 years ago -- New muffler -- New auxiliary bark pusher pumpEquipped with: -- Spare flail pump -- Spare flail motor -- New feed roll teeth -- Spare belts -- Spare pins -- Seal kits -- Spare clutch

PHL Industries 48" dia chipper, 6 knife wheel with 3 blocked, includes some spare knives, good working condition

Precision 58" dia, 6 knives, COMPLETELY REBUILT!! comes with warranty, BRAND NEW condition! ready for production

58" 6 Knife Precision Chipper

48" dia. 6 knife wheel with 3 blocked, bottom discharge, good condition

66" dia. 6 knife, side/ rear discharge, good working condition

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

48" 3 Knife Chip Pack S/N C-1029 75HP Electric Motor 5'x 5' Chip Screen

Precision 58" 6 Knife Chipper w/Horizontal Feed Top Discharge S/N 3135

Precision 58" dia, 6 knife, hard surfaced anvils, Kwik-Change knife system, THIS UNIT IS BRAND NEW!! in-stock and ready to ship

Precision 6 knife chipper and chip-pac, includes Precision 6' x6' shaker screen and cyclone, price includes repainted and gone through shop, good working condition

Precision 58" 3 Knife Horizontal Infeed Top Discharge

Precision 66" 6 Knife Chipper

Precision 66" 6 Knife Chipper

75" Precision 6 Knife Chipper S/N C-1732

Used Precision horizontal stationary chipper, 66”, 6 knife. Precision Husky stationary electric chipper Horizontal infeed Bottom discharge 6 knife Knife size: 21 ½” x 6” Choice of electric motors available Can provide a video of shaft/disk rotating with dial indicator on shaft. Chipper was cleaned & repainted, we do have photos before we painted it Additional photos, videos and information available. Contact us for a delivered price. Vidoe links to view chipper disc and shaft: https://youtu.be/3EXsqK1677s https://youtu.be/hNNTHv3zdMQ https://youtu.be/dw2Egvu91aw

Precicion 66" Chipper 6 Knife Horizontal Infeed / Top Discharge S/N C-2865