Scragg Mills For Sale
Category
Scragg Mills
18 Results Found
Cooper Sharp Chain Scragg, 48 In Blades, 18" max cut, Two 100 HP drive motors, 21 ft infeed with lot turner, 16 foot outfeed section. Dog house with control panel. Disassembled after included photos taken. Two large chip conveyors available as separate items.
1988 Cooper End Dogging Scragg Mill with 48" Diameter Blades & 125HP Motors S/N CM-6076. Out and ready to go.
Cooper Scragg End Dogging Computerized Set Works Cab W/Controls (2) 150 HP Motors 56" Saws 16' Capacity (2) 150HP Soft Starts 1200 Amp Allen Bradley Panel
MLS Number 11413038 Cooper Overhead End Dogging Scragg With Debarker And Gang Edger Transfer Chain Conveyor x 60’, H82,1-7.5 HP 480V gear drive 54" Cut Off Saw, 20 HP 480V motor, hyd stop gates, 20 HP hyd pack 4 strand x 12' long Debarker In Feed Deck, 5 HP 480V gear drive, H78 16” wide x 19’ long log haul belt conveyor (driven from debarker in feed tire drive) Cambio 24" Debarker, 75 HP 480V drive, spiked in/out feed rolls 20 HP 480V drive 3’ wide x 36’ long hour glass rolls transfer, 7.5 HP 480V gear drive 5-strand Scragg in feed deck x 20', H82, hyd log stop loader, 7.5 HP 480V gear drive Cooper Overhead Scragg Mill, 30 HP 480V 150 gal hyd package, variable speed cable drum feed works with pantograph arm Log positioning rolls on infeed w/ double overhead dogging system, 48” dia. saw husk(125 HP 480V each saw), setworks control 2-18” wide 2-position slab and side board belt conveyors, operators control cab w/ controls, camera and monitor for centering log 8-16’ length capacity, maximum log dia. 22”, largest square cant 12” x 12”, smallest square cant 4” x 4” 5-strand lower camel back landing transfer x 9’-6” long, 4-strand hyd lift transfer to gang edger and cant center bypass Center bypass rolls and belt conveyor to edger out feed landing transfer 10” mainland gang edger w/ 200 HP 480V drive,34” inserted tooth saws with 5/16” kerf(24 spare saws with collars), 2-2-2-4 spacing 6” x 50” mainland board edger w/ 150 HP 480V electric drive, 24” inserted tooth saws with 5/16” kerf, 8”-4”-4”-10”-6” pockets, 7-individual actuated self tailing belt conveyor out feed c/w splitters Camel back transfer,4-strand x 27-1/2’ long, H78B, 5 HP 480V gear drive 2-Saw Trimmer, 4-strand x 10’ long, 16’-4” between 20” dia. saws,10HP 480V drive on feed works and saws, 16” wide x 28’ long out feed belt conveyor, 5HP 480V gear drive 4-strand x 26’ long H78 camel back transfer w/ 5HP 480V gear drive
Corley Chipping Scragg Mill, Model CSM006, s/n 3778, 12x12" capacity, 26" over/under, mfg date 7-18-85, Paw Taw John setworks, 4- 26" blades, 2 key knife chipping heads with face knives, 2 saw lines, 2-50 hp Out and Ready to Ship
Evans Scragg Sharp Chain Feed Dbl Arbor , (2) 40" Bottom Saws, (2) 30" Top Saws, 50HP on Bottom & 30HP on Top, Cab and Controls
Morgan Scragg Mill - 48" Blades Conveyors All controls run by hydraulics. Saw needs 150 -200 HP Engine to run hydraulics on mill GANGRIP AND EDGER IN THE PICTURES HAVE BEEN SOLD...THE SCRAGG MILL PORTION IS STILL AVAILABLE.
$ 12,900
Pendu Model 6800 End Dogging Scragg Mill w/ Cab, Controls, 3 Str 4'8" x 8' Infeed Deck with 30 hp Hyd Pack
Portable Scragg Mill.runs off 125HP Electric Motor (Gen Set Required)36" Blades, Set up to do 3 1/2" Cants and Vertical Edgers to Put 2x4's or 2x6's out the back side, 40" Blades on Scragg, Electrical Included.
SFVG1200 twin vertical Band Saw 1200mm wheel blade size. Machine used for the log break down process in continuous flow sawmill layouts. Capacity to process logs up to 500mm in diameter and 3.000mm long. This machine is fitted with main motor, motor drive panel, servo motor thickness selection, adjustable saw guides, slabs pneumatic side pressers, special chain and hydropneumatic tensioning system to tension the Band saw. - Wheel blade width: 6”; - Minimum log Length: 1200mm; - Standard maximum log length: 3000mm - Minimum diameter: 120mm; - Maximum log diameter: 500mm; - Saw cut width: 70 to 300mm; - 4 set of pneumatic side pressing rollers for side boards; - Motor size: 2 x 75CV 4P 50hz (INCLUDED) - Drive Panel Included; - Central chain motor size: 7,5 HP 4P; - Linear Cutting speed: 30m/s; - Feed speed capacity: 48m/min; - Saw Blades are not included. - Infeed conveyor length: 4.000 mm included; - Outfeed conveyor length: 6.000 mm included; - Machine width: 5.000 mm; - Machine overall Length: 12.000mm - Servo motor thickness setting system (INCLUDED); - Approximate weight: 15.000 kg;