|
4 head Baker resaw, West Plaines 50 HP vertical cant sizer with programmable VFD on feed, Baker chopsaw with Pendu cant turners on rollcase, tilt-hoist, Curtis 10 HP compressor, Arrow regenerative line dryer with cooler, Dustek blower and baghouse with airlock and auger, 6’x35’ 2-strand deck with VFD drive. All starters and disconnects. Currently set up to chop, size, & resaw up to 16’ long. $98,500 608-606-9209
Equipment Location:Westby, WI
Leer Logging
608-634-4505
|
|
G TEK Grade Band Resaw S/N 8411310051400B001142, 100 HP motor, 16×16 capacity, 5” band (approx. 20 bands), w/ infeed, positioner and turner, outfeed and stop gate/separator, complete run around, 2 control cabs w/ computer setworks, w/ 3 hydraulic packs, w/ 1 30 HP and 2 25 HP motors and control center, 20 HP suction blower. $49,999. Call 740-222-1597 for more information.
Equipment Location:Waverly, OH
|
|
G Tek Single Head Grade Band Resaw With Complete Run Around System, Cab and Set works, 5 Way Seperator. Just about the Same as a Brewco B-1600. Additional Pictures available on Request
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
McDonough 62" Horizontal Resaw System Includes Resaw,Cab w/Setworks, Electrical, Complete Runaround Conveyors, Infeeds & Outfeeds, Ready to Run.
Set Up for Long Lumber & Bridgemat Production. Where cutting up to 40' Lengths.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
McDonough Linebar Resaw complete system, installed in 2005 and only run about 5 million board feet. Includes SD6A 3 press roll Linebar, Infeed, Outfeed, complete Setworks and Runaround. Still original paint on Table Rolls. Currently installed in Maine. This Resaw really is like brand new. Less than half price of new. Asking $400,000
Equipment Location:Cornish Flat, NH
Yankee Veneer Corp
207-841-8753
|
|
MAJOR PRICE REDUCTION - Horizontal Band Resaw System, cuts 18” cants x 16’ long W/ 4" band saw, S/N WPRWBS 131, landing & return table, outfeed tailing belt, infeed table, rollcases & operator controls - West Plains will rework wheels to accommodate a 5" band
Equipment Location:Kane, PA
Kittrell Sawmill Brokers and Appraisers
931-797-6284
|
|
Baker 4 Head Bandsaw. 7.5HP.
Equipment Location:MN
Pallet Machinery Group
540-644-9220
|
|
3 Head
Equipment Location:VA
Pallet Machinery Group
540-644-9220
|
|
4 Head , return belt to go back on it. It would need all new guides for each saw, and 1 motor. Located in Pennsylvania
Equipment Location:VA
Pallet Machinery Group
540-644-9220
|
|
4-Head Re-Saw, each head equipped with a separate 30 HP TEFC motor and 3-sided feed works with: Rough-top belting, powered side feed rollers, non-powered hold-over wheels. -- Fully variable 20 - 120 FPM feed speed. The system is perfectly suited for resawing squares, and 3-sided cants into various thickness of lumber. -- Equipped with: Roughtop conveyor belt, powered side feed rollers, and non-powered holddown wheels, return conveyor, and air blade tensioning. -- Specifications: 12" Cutting height x 12 wide, uses 0.035" x 1" x 13'-2" band blades, creates less 1/16" kerf; 4" diameter, 500 CFM saw dust outlet per head recommended. -- Completely pre-wired with NEMA 12 enclosure with starter, disconnect and overload protection, and start/stop stations. -- Feedworks/Conveyor Hydraulic Motor driven by main motor. -- Features include: Air tensioning system; blade height adjustments can be made quickly via hand crank; Low-profile flat guides for maximum accuracy. 28" Dia. all-steel band wheels, with crown. -- Material is firmly held in place during the entire cut - the only continuous feedworks on the market today!
Equipment Location:MIDWEST
Jim Reedy
800-374-5009 ext:455
|
|
2-Head, 30 HP TEFC motor, hydraulically driven feed from head motor, feed speed from 20 - 120 FPM, feed works with 12" wide rough top belt conveyor on self-centering rollers, and holddown wheel. -- Mechanical spring blade tensioning, 0.035" x 1" x 13-1/6' blades, 0.072" kerf. -- Baker flat guides for higher production, accuracy & extended blade life.
Equipment Location:MIDWEST
Jim Reedy
800-374-5009 ext:455
|
|
BAKER BBR-O (AX) Horizontal Band Resaw w/Powered InfeedBaker Single Head Re-Saw with 7" wide x 7" high cap.;Specifications: -- 1/4" - 4" Cutting height; 20 HP TEFC saw motor. -- 28" CNC machined dynamically balanced all steel band wheels. Spring blade tensioning system. Feed System: -- Powered infeed belt tilts 0° - 10°, variable speed from 20 - 120 FPM controlled by a hydraulic flow valve. -- Complete with: 5-1/2" Wide rough top conveyor belting with powered top hold down belt; 4" dust outlet (500 CFM). -- Recommended blade (not included): 0.035" x 1" x 14'-2" Hardback.
Equipment Location:MIDWEST
Jim Reedy
800-374-5009 ext:455
|
|
Baker BBR-0 6-Head Horizontal Resaw System, 13 Sets of Side Press Rolls, 6" x 35' Feed Through Belt Conveyor, (6) 20 hp, 1750 Rpm Drives, Air Bag Tension, Push Button Control, S/N 95-1486
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
Baker 3 Head Band Resaw with Return Model BBR-O, 20HP Electric Motors, S/N 95-1256
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
BAKER A Single-Head Resaw -- Specifications: Max. 7" x 7" timber cap w/Slide Return; hydraulic variable feed speed rate 0 - 120 FPM; 6" Wide rough-top belted infeed conveyor for easy-to-produce lap siding. -- Few moving parts and few adjustments for quick mastery. -- Equipped with: 20 HP Electric motor, 28" dia, CNC machined all wteel band wheels; 1" or 1-1/4" x 13' - 2" x 0.035" hardback band blades; optional Diesel or Gasoline engines available. -- Includes: Operations manual, parts list & tool kit.
Equipment Location:MIDWEST
Jim Reedy
800-374-5009 ext:455
|
|
BAKER A Single Head Re-Saw w/Return -- Specifications: 20 HP TEFC motor, 6" wide x 7" high material cap. or 8" wide x 4" high above the blade with conveyor set a 0°. -- Equipped with: Spring infeed holddown, variable speed controlled by a hydraulic flow control valve, tilting conveyor, hydraulic feed drive via a 2 HP pump motor and 28" steel bandwheels; features BAKER'S exclusive low profile flat plate guide system w/rear rollers. -- Includes: (90) Brand new bands.
Equipment Location:MIDWEST
Jim Reedy
800-374-5009 ext:455
|
|
BAKER ABXX 40 HP Resaw, 12" H x 16" WSingle-Head Band Resaw can be used to cut boards, cants, or reclaim slabs, This Resaw can process a Timber up to 12" H x 16 W" in any desired length. Hydraulic variable speed from 0 - 95 FPM. -- This Model "ABXX" Resaw covers a large range of applications from small to large facilities, they are simple to operate and maintain with few moving parts and few adjustments. -- Complete With: 40 HP Electric Motor, 28" all-steel band wheels, 14'10" x 1" x 0.035" band saw blade, BAKER's exclusive Low-Profile Flat Guide System, spring blade tensioning and heavy duty construction. -- Included: Hydraulic infeed hold-down, extra wide hold-down wheel system.
Equipment Location:MIDWEST
Jim Reedy
800-374-5009 ext:455
|
|
Baker C 4 Head Resaw
Early to Mid 90s
6" w × 12" h capacity
20hp 3ph 480v motors on resaw heads
10hp 3ph 480v VFD
20-120 fpm
Uses 1" × .035 × 13'2" blades
Saw is in overall good condition and ready to go to work
Equipment Location:Colorado
Mitch Stevens
828-773-6986
|
|
Baker single head band resaw w/20 hp. electric motor.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
|
|
Vertical Band 6 inches blade, wheel 48” diameter Approx. 20 years old
Equipment Location:AB
Pallet Machinery Group
540-644-9220
|