Sawmill Equipment For Sale
.gif)
3651 Results Found
Call for Price
General Motors Power Takeoff Unit Detriot Diesel #5136548
Call for Price
Go Fast Resaw 15 HP Motor Put under power to test, never put into production.
Call for Price
Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'
Call for Price
GoFast 2-Head Resaw 10 HP main motors Go Fast Board Deduster
Call for Price
2023 Go Fast 6x12 Resaw Has minimal use
Call for Price
.jpg?width=300&height=200&mode=pad)
2022 GoFast Single head Resaw- only used 6 months! #00902
$ 12,000
Go-Fast Single Head Resaw Self-contained hydraulic feed with air bag band tension. ( NO motor ) In good condition. Make an OFFER today.
$ 85,000
.jpg?width=300&height=200&mode=pad)
GO FAST 2-Head 6 X 8 Master Resaw w/6" x 8" Cut Cap. Specifications: -- 15 HP TEFC motors, max. blade height 5-3/4" from conveyor belt x 8" wide; 20"; dia. bandwheels; self-contained hydraulic system with feed speed from 0 - 150 FPM, 6" wide feed belt conveyor and return; and top mounted holddown wheel. -- Complete with: -- Pneumatic blade tensioning system; heavy duty 2-7/16" arbor and bearings; easy crank for adjustable blade position; 3" right-side fences. -- Includes: -- Operator return table; 15'-1" x 1" wide bandsaw blades; 4" square dust chutes (square to round transitions available). Options available: -- Secondary hold-down wheel; outfeed speed-up roller; ripsaw fence attachments; & more.
GO FAST 6 X 12 Master Resaw w/6" x 12" Cut Cap. Specifications: -- 20 HP TEFC motor, max. blade height 5-3/4" from conveyor belt x 12" wide; 20"; dia. bandwheels; self-contained hydraulic system with feed speed from 0 - 150 FPM, 10" wide feed belt conveyor; top mounted holddown wheel. -- Complete with: -- Pneumatic blade tensioning system; heavy duty 2-7/16" arbor and bearings; easy crank for adjustable blade position; 3" right-side fences. -- Includes: -- Operator return table; 15'-1" x 1" wide bandsaw blades; 4" square dust chutes (square to round transitions available). Options available: -- 22 HP Gas Engine; 10 HP 1-Phase; 575 Volt 3-Phase; secondary hold-down wheel; outfeed speed-up roller; ripsaw fence attachments; & more.
$ 16,500
Goring Kerr metal detector, 50"x 45" opening, new electronics - Call Jeff for more info at 574-370-5050
Call for Price
GREENMAX - EPS-AC-100, ...Cold Press DensifierSpecifications: -- EPS Polystyrene Foam Densifier -- Ratio: 50 to 1 -- Volume: 220 Lbs/Hr -- No Conveyor -- Loaded ont your Truck
Call for Price
7' x 36" 3 Strand Board Deck w/ 3 Arm Drop Out Tipple Elec. Drv.
Call for Price
Grizzly 10ph 4 Bag Dust Collector
Call for Price
Grizzly G0919 12" 2 Head Resaw
7.5 HP 220/440 volt 3-phase wired 220 volt 10” dust inlet Total filter serface 261 sq. Ft. 99.9% effective at .2-2.0 microns 3468 cfm @4.3” static pressure
Call for Price
Call for Price
$ 10,500
Gruber Systems 12’ Vibration Conveyor Tables with 230V 3 Phase Vibrators Seven Available. Six with Vibrators and one without. These powerful 3-phase electric vibrator-equipped Vibe Tables offer heavy-duty performance, quieter operation, and lower compressed air volume requirements compared to pneumatic vibrator equipped tables. Specifications: Frame: Height (to top of wheelway): - 28” (71.12 cm) Width - 24” (61 cm) Length - 120” - 144” (304.8 - 365.76 cm) Wheelway (wheel center to wheel center): Width - 20-1/8” (51.12 cm) Pneumatic Vibrator (@20 psi): PSI required to Start - 25 PSI (1.75 kg/cm²) Vibrations Per Minute (VPM) - 3,200 Force - 255 lb-force (115.6 kg-force) Flow - 9 CFM (0.25 m³/minute) Electric Vibrator (220/440 volt, 3Ø, 60hz. @ 10% setting) Vibrations per Minute - 3,456 VPM Pounds of force - 230 LB Full load current - 1.26 / .69 Amps Starting current - 9.8 / 4.9 Amps
Call for Price
