Equipment For Sale

Precision Chip Collector Cyclone 60" dia Visit https://benjones.com/shop/102363/ for more information.

Precision 58" Chipper 3 Knife w/100HP Motor

Precison 4k tub type knife grinder

New conveyor 20' length w/ drive

Precision vibrating conveyor, 18" wide pan x 55' long, 8" sides, electric drive, good working condition

40’ Precision Vibrator

Precision 58" dia, 6 knives, COMPLETELY REBUILT!! comes with warranty, BRAND NEW condition! ready for production

Precision vibrating conveyor, 18" wide pan x 30' long, 12" tall sides, BRAND NEW fiberglass paddles, excellent condition

Precision vibrating conveyor, 18" wide pan x 20' long, 10" tall sides, electric drive, good working condition

Precision vibrating conveyor, 18" wide pan x 27' long, 10" tall sides, electric drive, good working condition

66", 6-knife, bottom discharge

58" 6 Knife Precision Chipper

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

Precision Disc Scalping Screen Model PDS648 48” wide x approx 8’ long 6 shafts and the discs are stitch welded on

Precision rosser head debarker, 36" capacity, electric drive on head, self-contained hyd unit for carriage etc., upgraded to chain drive for carriage, has flat barn sweep underneath, working condition

Includes 27' x 14" dia distribution auger, 3 each 35' x 12" dia loading augers, complete steel structure with columns and beams, control station without starters.

Precision 55 screener, was working when pulled out of production.

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Precision 6'x6' Shaker Screen s/n S1899

Precision Chip Screen 6'x6', 1-3/4" screen, s/n S1729