Drum Dryer For Sale
12 Results Found
ASTEC Rotary Hot Oil Tube Type Indirect Dryer for Wood and other Products;Complete with the following components and features: -- 10 Ft. x 60 Ft., Carbon Steel, Rotary Drum. -- 40 TPH design capacity. -- Hopper and Screw Feeder. -- End Discharge with Hood and a stainless steel Auger Discharge. -- Hot oil Inlet and Outlet Manifold. -- Trunnions & Support Structure. -- 75 HP Drum Drive Motor and reducer, (ratio 64.42 to 1) with chain & sprocket. -- Control Panel with SIEMENS PLC Controller. -- Thrust Idler Hydraulic Pump Panel. -- Hot Oil Pump Skid Consisting Of: ● (3) BLACKMER System-One Centrifugal Pumps, Model FRM, 316 Stainless Steel. Size 8 X 10-13, approximate 4200 gallons per minute at 110' head at 275 PSI at 100°F. Each driven by a 100 HP Motor. ● (3) Strainers with miscellaneous Piping and Valves. ● (1) XYLEM 2-pass carbon steel shell & tube Heat Exchanger. Shell rated 125 PSI at 1600°F., tubes 150 PSI at 1375°F. -- HEATEC Convectec Hot Oil Heater complete with a Control Panel, Expansion Tank and (1) TWIN CITY fan, size 917, Type RBO-SW. Driven by a 15 HP Motor. Operating temperature up to 550°F output and re-circulation input of 490°F input.NOTES: ● Dryer, Pump Skid, or Heatec may be purchased separately. ● System last used with drying wood chips from 45% down to 10% moisture. To save on gas fuel costs, the system was originally mostly heated with a bark burner which has been sold. The Heatec has another burner which was originally also connected, it is rated for 40 MM BTUs and other gas burners up to 100 MM BTUs are available. ● Professional rigging and loading available.
ASTEC Single-Pass Rotary Dryer for Wood and other Biomass Products;Complete with the following components and features: -- 10' x 25', Carbon Steel, Single-Pass Rotary Drum. -- Hopper and Screw Feeder. -- End Discharge with Hood and a stainless steel Auger Discharge. -- Trunnions & Support Structure. -- 60 HP Drum Drive Motor and reducer, (ratio 43.78 to 1) with chain & sprocket. -- Control Panel with SIEMENS Milltronics Model "BW500/L" Controller. NOTES: ● 2015 Estimated year of manufacture. ● No Heat supply. ● System last used to partially dry wood chips. ● Professional rigging and loading available.
EARTH CARE PRODUCTS, INC. 10½ Ft. x 32 Ft. Triple-pass Rotary Drum Dryer System with Gas Burner;Complete with the following major components: -- 10.5 Ft. x 32 Ft. (despite the model DB-1030) Triple-pass Insulated drum. -- Trunion Bases, and 30 HP Drum Drive. -- High efficiency Cyclone, Cyclone outlet Airlock. -- 100 HP Dryer Main Fan, and Ducting. -- 25 MM BTU Gas Burner complete with Refractory Lined Furnace and Gas Train. Notes: ● The Trunion Tracks and Trunion Wheels are in good condition as is the drum interior. The system was renovated in 2015 and not used much after the work was done. ● The equipment is still in-place.
HEIL 8' x 24' Rotary Drum Dryer with the following components and features: -- Drum Drive -- (2) Trunnion Bases with (2) Wheels each -- 8' x 24' Single-pass drum with center-fill and shell flighting. This type single-pass is actually often rated for capacity greater than a triple-pass dryer. -- The Drum and Trunions were completely Rebuilt but never put back into service.
M-E-C Dryer 13’x60’ Dryer System with Dust Burner.This System is complete with the following components: -- 40 MM BTU McCONNELL Dust Burner with back-up Oil Burner. -- 13’ x 60’ M-E-C Triple-pass Rotary Dryer Drum. -- All Controls. -- Receiving Cyclone & Multi-clones. -- Main Fan with Fan Motor. -- Discharge Stack. -- All related ducting and steel structure. -- Plans, Manuals and Blueprints as available. -- Professional Rigging and Removal is available.Note: This is one dryer system despite where two or more may appear in different photos.This beautiful System was originally installed in 1989, upgraded by M-E-C in 1995, and then continued in operation from 1995 to 2003. Although the equipment is now about 25 yrs old, it has only been operated for about half that time and was always housed indoors in a supervised environment.
Wood material drying system comprised of the following major components: -- M-E-C 12’x42’ Rotary Drum Dryer with Trunnions and 25 HP Drum Drive; configured with pull-thru Pneumatic System. -- Main ID Fan with Motor. -- JACKSON LUMBER HARVESTER manufactured WEBB® 30 MM BTU biomass burner with Fuel Feed Fan and Vortex Induced Side FD Fans. -- MACProcess or MAC Baghouse Filter, Model with Airlock discharge. -- Screw bottom receiving bin with grizzly. -- Bucket Elevator. -- Wet Bin Storage Silo. -- Dry Bin Storage Silo with Receiving Cyclone and Airlock. -- Electrical Control Container unitized and housing Programmable Logic Control (PLC), Input/Output (I/O) panel, Motor Control Center (MCC) Cabinets with motor starters, disconnects and HMI control software. -- Hammer Mill for fuel grinding with screw conveyor discharge. -- High Pressure System with Lobe Type Blower and Feeder. -- Product Feeder from Silo. -- Dryer input Belt Conveyor.
M-E-C Model 10' x 40' Triple Pass Rotary Drum Dryer;Complete with the following associated components: -- MEC 10 Ft. diameter x 40 Ft. long, 3-Pass, Rotary Drum. -- Trunnion Bases with Trunnion Wheels. -- Drum Drive with 40 HP Motor, Sprocket and Drive Chain. -- Main Fan with 200 HP Motor.NOTES: ● No Burner. ● Good trunnion tracks and wheels. ● Professional rigging & loading is available.
MEC 12' x 48' Gas Fired Triple-Pass Dryer System for Wood and other Agriculture Products; Complete with the following major components: -- Rotary Dryer: MEC 12' Dia. X 48' L, 3-pass, Rotary Drum Dryer with Trunnion Bases. -- 50 HP Drum Drive with Gear Reducer and actual Drum Sprocket. -- 45 MM BTU Gas Burner with Controls. -- High Efficiency Cyclone with Vortex Breaker, and Rotary Airlock. -- Dryer infeed multiple Screw Conveyors. -- Dryer Discharge Conveyor. -- Dryer Drop-out Box Bin with Airlock and Discharge Screw. -- Wet Scrubber for final fine particulate removal. -- 800 HP Main Fan that pulls from dryer/burner inlet through the wet scrubber. -- Complete Electrical System.NOTES: Drum Trunnion Tracks were very recently re-honed. Wheels were reground too, only a few months of use since then. The burner was used only about (18) months since brand new. The dryer has had about (18) months of use since reconditioning. However, it needs a new skin due to poor handling upon moving and installation. OPTIONAL ITEMS: ● (2) Twin Paddle Blenders. ● (1) Railcar high pressure loading system with lobe Blower. ● (2) Counterflow product coolers. ● Real Estate site with multiple buildings and rail siding.
SPROUT Rotary Drum Dryer with Gas Burner;Complete with the following components: -- 7.5 Ft. x 24 Ft. Steel Rotary Dryer Drum. -- Natural Gas Burner (may be converted to LP) with 13.5 Ft. Refractory Lined Furnace Tube. -- Belt Drive with Gear Reducer and Electric Motor. -- Trunnion Bases complete with Forged Trunnion Wheels. -- Forged Trunnion Tracks (weld-on style) ...look like new. -- Vertical drop material Inlet Transition with Side Access Door. -- Rated for approx. 2 TPH water evaporation or about 2.5 TPH wood sawdust output. -- OPTIONAL ITEMS: ● Receiving Bin with Airlock and Screw discharge Conveyor. ● Material Input Screw Conveyor. ● Main Fan.
10 MM BTU Webb Burner with controls 12' x 42' Triple Pass Drum Dryer Blower/Piping Screen Misc parts will be included. This system is no longer needed at the current facility.
WESTEC 13X62 Drum Dryer; Used Dryer 3-Pass Rotary Drum manufactured by one of the premier makers. -- Size: 13' x 62', Heavy Duty. -- 10" x 3" Drum Tracks (steel drum tires) with many years of good service to go. -- This unit is in very good condition compared to many drums. The interiors are just about as nice as they come. -- Higher efficiency drying. Example: 34,000 Lbs/Hr at 850° inlet temperature at 78,000 ACFM, 50% to 5% (wet basis) moisture content . Note: -- Drum only - no Trunnion Bases or Drum Drive included. It is built to last a long time with heavy duty Shell and Inner Passes and heavy duty Trunnion Tracks.
WESTEC 13X62 Drum Dryer; Used Dryer, 3-Pass Rotary Drum manufactured by one of the premier makers.Specifications: -- Size: 13' x 62', Heavy Duty. -- 10" x 3" Drum Tracks (steel drum tires) with many years of good service to go. -- This unit is in very good condition compared to many drums. The interiors are just about as nice as they come. -- Higher efficiency drying. Example: 34,000 Lbs/Hr at 850° inlet temperature at 78,000 ACFM, 50% to 5% (wet basis) moisture content . Note: -- Drum only - no Trunnion Bases or Drum Drive included. This drum is in very good condition and may be placed back into service without further work to be done. -- It is built to last a long time with heavy duty Shell and Inner Passes and heavy duty Trunnion Tracks.