HOMAG OPTIMAT KAL 210/7/A20/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Working Capacity: Edge thickness cap.: 0.4 - 20 mm; min. panel width: 55 mm (2-1/4"); panel thickness: 12 - 60 mm; min. edge length: 7.8". -- Infeed Section:(2) Premilling heads, each with 3 kW - 6,000 RPM motor, (1) with jump control; chip blowoff unit after last head; SIKO digitals for horizontal & turret for vertical adjustments; -- Preheating infeed fence for panel edge. -- Automatic 2-coil feed magazine for coil material up to 3 mm thickness; strip feed magazine for up to 20 mm (3/4") solid wood banding. -- "QA 34 Quick Melt" Glue system per melt hopper feeder & roller applicator (reversible); pneumatic pressure roll section with (1) large dia. driven & (6) idle rollers. -- Workstations:Double motor front & rear end trim: 0.7 HP - 12,000 RPM Motor ea.; pneumatic chamfer setting. -- Top & bottom rough trims: 2 HP - 12,000 RPM motor ea. -- Top & bottom profile trim units: For leading & trailing edge, (4) 0.6 HP - 12,000 RPM motors; up to 4 mm edge thickness: All trim station motors are: 200 Cy - HF and equipped w/electronic brakes. -- Profile tracing from: Top, bottom and side for chamfering or rounding of pretrimmed PVC edges; pneumatically controlled blowing nozzles. -- Max. edge thickness: 3 mm (1/8"); panel thickness: 12 - 60 mm (15/32" to 2-3/8"); unit laterally adjustable by max. 50 mm (1-31/32"); Collection box for PVC shavings. -- Height adjustment with top pressure beam without tools; manually adjustable with digital mechanical counters. -- Profile Edge Scraping Unit with: Electropneumatic adjustment. -- Top & Bottom buffing unit. -- Feed & Holddown System:Motorized top pressure beam with powered V-belt holddown. -- 80 mm Wide Heavy-Duty feed chain w/rubber pads, automatic chain track lubrication system. -- 5 HP Feed drive for variable feed speed of 23 - 98 FPM. -- Operator & Machine Control:HOMATIC "PC 22", 2 GHz CPU with 512 MB RAM, USB port; functions in XP Windows environment. Keypad with TFT flat screen LCD display, onscreen fault diagnostic, part & lineal feet/meter tracking, etc. Diagnostic analysis from HOMAG via Modem fault diagnostic is possible. -- Complete with:SIKO Digital adjustments on: Top & Bottom trim, fine trim, and scraper stations; 10 KVA - 200 Cy frequency converter, electronic DC brakes on all trim motors. -- Sound cabins for all trim workstations; adjustable outboard panel support with floor supports. -- Actual Model is Optimat KAL 210/7/A20.S2.NOTE: Seller states that the Edgebander was in use until recently. The Corner Rounding stations are no longer in working condition

HOMAG KAL 310/7/A3/S2 EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING)Working Capacity: -- Edgebanding thickness in rolls (min/max) 0.3 - 3 mm. -- Panels thickness (min/max) mm 12 - 60 (1/2" through 2-3/8"). -- Feed speed (adjustable) 18 - 25 MPM (59 to 82 FPM). Front-End Equipped: -- In-feed fence, manual digital positioning. -- Pre-Milling Unit (vertical joint trimmers) (2) x 3 Kw each. -- Lamps to pre-heat the work pieces edge. -- Edge Magazine, vertical coil cart with 2 positions. -- Gluing Unit QA 34, EVA (Hot Melt) -- Side Pressure Zone, (3) rollers, adjustable by N.C. servo motor. Working Units: -- End Trimming Unit HL 81 Motors, 2 x Kw 0.22 (0.50 HP) -- Pre-Rough Trimming Unit: Top/Bottom, 2 x 0.55 Kw. (0.75 HP) 12,000 RPM motors, none tilt with digital indicator positioning. -- Multi Function Unit FK 11: Profile Contour Trimming, 2 x 0.4 Kw, 12000 RPM motors, for linear top/bottom edge trimming and vertical front/back corner rounding. -- Profile Edge Scraping Unit:Pneumatic in/out and manual digital indicator positioning. -- Glue Scraper:Top/Bottom, flat panel surface glue scraper. -- Buffing Unit: Top/Bottom oscillating buffing motors 2 x 0.25 Kw (0.35 HP).Operator & Machine Control: -- HOMATIC NC 21 controller, flat color LCD screen with keyboard and mouse input. Complete With: -- Top pressure system with rubber belt. -- Panel Support Outrigger. -- Sound and safety hoods over all working stations. Actual Model is HOMAG KAL 310/7/A3/S2

HOMAG - OPTIMAT KDF 440C: Special RH Feed Direction Edgebander w/Premilling & Corner Rounding (aka BRANDT - KDF 440C)Specifications: Premilling & Corner Rounding; HIGHFLEX Automated package. -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 5/16") Edge; 8 - 60 mm (5/16 - 2-3/8") panel thickness; 160 mm (6-3/8") min. panel length; 70 mm (2-3/4") min. panel width.Equipped with: -- Premilling Station: (2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chipfree & clean panel edges. Equipped with diamond cutterheads -- Infeed Fence with: Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between: Glue roller and pressure section. -- Automatic Edge Magazine: Strip & coil stock; strips: 0.4 mm - 8 mm (0.016 - 5/16"); coils up to 3 mm PVC; "HD" guillotine "Quick Change" Glue Tank for maintenance & glue color change. -- Pressure Section: 1st Roller driven plus: (3) Idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- BRANDT "Power Touch Control"; memory: 256 MB RAM; 1 GB flash card drive; Operator control panel: 22" Color HD widescreen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming -- (2) Motor @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/Bottom (2) motors; 0.55 kW (3/4 HP) - 12,000 RPM; auto. tilt positioning; 0° - 25° with combination flush/radius/chamfer cutterheads; horizontal & vertical tracing wheels.Equipped with: Brushless multiaxis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes: (3) Positioning options: Profile-1, Profile-2; flush trimming -- Corner Rounding Unit(1) Motor: 0.35 kW (1/2 HP) - 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness -- Scraping, multi-profile (PVC): Top/Bottom with (2) profiles.1 mm & 2 mm or 3 mm instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels. - PVC scrape collection box. -- Scraping Glue Unit: Flush Top/Bottom on panel surface with floating insert knives. -- Buffing Unit: Top/Bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM. -- RIEPE anti-adhesion and RIEPE detergent.Complete with: -- Motorized, programmable holddown pressure beam; padded sound enclosure and used tooling. -- Actual Model: RH Feed HOMAG - OPTIMAT KDF 440C (aka BRANDT - KDF 440C, but branded HOMAG).

HOMAG - OPTIMAT KDF 440C: Special RH Feed Direction Edgebander w/Premilling, Corner Rounding & Return Conveyor (aka BRANDT - KDF 440C)Specifications: Premilling & Corner Rounding; HIGHFLEX Automated package. -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 5/16") Edge; 8 - 60 mm (5/16 - 2-3/8") panel thickness; 160 mm (6-3/8") min. panel length; 70 mm (2-3/4") min. panel width.Equipped with: -- Premilling Station:(2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip free & clean panel edges. Equipped with diamond cutterheads -- Infeed Fence with: Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between Glue roller and pressure section. -- Automatic Edge Magazine: Strip & coil stock; strips: 0.4 mm - 8 mm (0.016 - 5/16"); coils up to 3 mm PVC; "HD" guillotine "Quick Change" Glue Tank for maintenance & glue color change. -- Pressure Section: 1st Roller driven plus: (3) Idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- BRANDT "Power Touch Control"; memory: 256 MB RAM; 1 GB flash card drive; Operator control panel: 22" Color HD widescreen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming:(2) Motor @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit:Top/Bottom (2) motors; 0.55 kW (3/4 HP) - 12,000 RPM; auto. tilt positioning; 0° - 25° with combination flush/radius/chamfer cutterheads; horizontal & vertical tracing wheels. Equipped with: Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes: (3) Positioning options: Profile-1, Profile-2; flush trimming -- Corner Rounding Unit:(1) Motor: 0.35 kW (1/2 HP) - 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness -- Scraping, multi-profile (PVC): Top/Bottom with (2) profiles. 1 mm & 2 mm or 3 mm instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels. - PVC scrape collection box. -- Scraping Glue Unit:Flush Top/Bottom on panel surface with floating insert knives. -- Buffing Unit: Top/Bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM. -- RIEPE anti-adhesion and RIEPE detergent. -- Complete with:Motorized, programmable hold-down pressure beam; padded sound enclosure and used tooling. -- Options Include:Homag Return Conveyor as pictured. -- Actual Model: RH Feed HOMAG - OPTIMAT KDF 440C (aka BRANDT - KDF 440C, but branded HOMAG).

HOMAG - SAWTEQ B-400 PROFILINE 38/16: Rear Load Automatic Panel Saw -- Specifications• HOMAG SAWTEQ B-400 (HPL 400) US Edition is a flexible saw center. • Equipped with rear lift table, feed system, main saw and scoring saw.• The saw is capable of executing a wide range of cutting pattern types.• Maximum Panel Size: 62.99" X 145.67 (1,600mm x 3,700mm)• Cutting Length: 149.6" (3,800mm)• 145.6'' (3,700 mm) pull back capacity• Three Air Tables• Main Saw Blade Diameter: 450mm• Scoring Saw Blade Diameter: 180mm• Main Saw Motor: 37.8 HP• Blade Projection: 4.9" (125mm)• Saw Carriage Speed Forward: 0 - 492 FPM• Saw Carriage Speed Reverse: 492 FPM• Program Fence Speed Forward/Reverse: 82/295 FPM• Automatic Side Pressure Device• PowerControl / PowerTouch Touch-Screen w/ Windows 10• CADmatic 5 Control with Assistance Graphic• Actual model: HOMAG SAWTEQ B-400 38/16 (HPL 400) US Edition

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.011. - 0.118"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt: QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute (5) heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Rough/Pre-Trimming Unit:(2) 0.55 kW 0.74 HP (0.55 kW) - 12,000 RPM Motors, tilting range +/- 1° & counter-rotating to machine feed to prevent blowout & .Height adjustment synchronized with the top pressure-beam .With digital counters. -- Scraping Unit:Top & bottom for thick PVC/ABS, electro-pneumatic positioning & pneumatically activated. Pneumatically-controlled blow off nozzles. Height adjustment synchronized with top pressure beam. -- Flat Glue Scraper Unit:Top & bottom to remove potential glue squeeze-out, electro-pneumatic positioning in and out of the processing area & electro-pneumatically activated height adjustment synchronized with top pressure beam. -- Buffing Unit:Top & bottom edge buffing/polishing. Operator & Machine Control: -- Power Touch Control Multi-Touch Screen C

HOMAG - AMBITION 2480: Edgebander (w/Premill & Corner Rounding) -- SpecificationsWorking Capacity. Coiled stock: Min./max. edge thickness 0.3 - 3 mm (0.011. - 0.118").Strip material min./max. Edge Thickness: 0.3 - 20 mm (0.011 - 0.78").Solid Wood Material min./max. Edge Thickness: 0.6 - 20 mm (0.024 - 0.78").Panel stock min/max thickness: 8 - 60 mm (0.472" - 1.574"); panel overhang: 30 mm (1.18").Min. workpiece width 2.36" (60 mm) with workpiece thickness ≤ 22 mm; 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units Top/Bottom spraying device prior to workpiece premilling. Designed for applying a separating agent for: Easier cleaning of any residual glue on the panel. -- Infeed FencePreheated, manually adjustable infeed fence with: Digital indicators. -- Premilling Station(2) 2.2 HP (3.0 kW) - 150 Hz - 9,000 RPM: Vertical jointing spindle motors; equipped with: Panel blow off device & SIKO digital counters for adjustments. -- Preheat UnitQuartz lamp for: Heating substrate edge before glue application. -- Edge MagazineMultipurpose 2-coil magazine expands capability by: Running coiled material & strips. Max. roll diameter: 400 mm & 830 mm.Magazine height adjustment. Allows greater usage of varying panel heights by raising & lowering the magazine table; allows the Operator to center the panelon the edgebanding. -- Gluing System: HOMAG Quickmelt Premelting Unit. QA 3: Quick Melt Overhead Unit & Heated roller applicator; digitally displayed thermostat for both upper & lower unit. 34 mm Dia. Glue Roller. Allows excellent control of temperature for: Optimum bonding results with individual adjustment for leading & trailing glue gates.Lower melting unit equipped with: Automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast 5-minute heat up time. -- Pressure SectionProgrammable (Servo). Automatic pressure zone adjustment: (1) Large 150 mm dia. driven; (4) 70 mm dia. idle rollers; pneumatic pressure control depending on edgebanding material used.Workstations -- End Trimming Unit: PK 25(2) 1 HP (0.8 kW) - 200 Hz - 12,000 RPM Motor ea.: Cuts excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. - Programmable (Servo). -- Rough/Pre-Trimming Unit - BF 10(2) 0.55 kW (0.74 HP) - 12,000 RPM Motors; tilting range: +/- 1° & Counterrotating to machine feed to prevent blowout.Height adjustment synchronized with: The top pressure-beam. -- 4-Motor Corner Rounding Unit: FF 32(4) 0.54 HP (0.4 kW) - 12,000 RPM; Motors to fine trim the edge overhangs at the workpiece front & rear vertical edge.Max. feed speed: 20 MPM (66 FPM) when using "Corner Rounding Unit". -- Open Space -- Profile/Bevel Scraping Unit PN 10Top & Bottom for thick PVC/ABS; electro-pneumatic positioning & pneumatically activated. Pneumatically controlled blow off nozzles. Height adjustment synchronized with: Top pressure beam. -- Flat Glue Scraper Uni

HOMAG BAZ 211 VENTURE 21M Machining Center W "C" Axis -- Maximum Working field: X-Axis 3,225 mm (126.9"), Y-axis 1,500 mm (59"), Z-axis stroke 300 mm (11.8"), max work piece thickness 60 mm (2.4"). -- X-axis travel speed 80 MPM (262 FPM), -- Y-axis travel speed 60 MPM (197 FPM), -- Z-axis 40 MPM (131 FPM), AC Brushless Servo motors with digital drive and linear guides ensure high speeds with a smooth acceleration-and-deceleration. -- Working area: Working tables consist of (6) adjustable support rails, (2) vacuum cups per rail; laser unit to aid in the quick positioning of the vacuum cups. -- Machining unit: (1) 14.75 HP (11 kW) liquid cooled electro-spindle router (1,500 - 18,000 RPM), "HSK F63" quick change tooling; 12-position ATC automatic tool changer, "C" axis for 360ø horizontal processing. -- Drilling Unit: Vertical drilling head with (17) individual vertical spindles, 11-spindles in "X", 7-spindles in "Y", spindles on 32 mm centers. (1) saw blade aggregate, 125 mm dia; (1) 4-spindle lock case horizontal trimming unit aggregate. -- "POWER CONTROL PC 85" Numerical control with: "WOODWOP + BAZ" interface software, "WINDOWS NT"; icon driven with a graphical interface to allow the operator to quickly and efficiently create programs. -- Includes: 144 MB Disk drive, CD ROM drive, 12" color LCD monitor. -- Features: RS-422 Serial & USB connection to PC (up to 300 meters), (2) line adaptors RS-232 & 485.2 with 9-25 pin and card for RS-232 line (cable not included). -- Features: Multitask operating system, input/output modules, axes override, 4-axis interpolation, "WOOD SCOUT" diagnostic graphics aid for programming, machine data & tool management. -- Editor Module for PC with same look and functionality of software on the machine, allows transmission of programs and work lists; Required office PC configuration (not included): Pentium processor, 8 MB RAM, 8 MB hard disk; VGA video card. Complete with: -- ELMO 100 cm/h vacuum pump; perimeter protection cage; user & maintance manuals on CD with wiring diagrams and operation of Numerical Control. -- "C" Axis -- Actual Model is BAZ 211 VENTURE 21M.Riggers are required for tear down and loading

HOMAG ABD 050 CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) Horizontal drilling aggregate with (1) individual spindle; with servo control of the "X" Axis; (1) glue & dowel injector with glue flow control; (1) vibrating hopper dowel feeder. -- Working Capacity:Part size: Length 20 mm - 1,250 mm (.75" - 49") Width 20 mm - 800 mm (.75" - 31.5") Thickness 10 mm - 60 mm (.4" - 2.4") thick.Machine is set up for 8 mm Dia. x 30 or 35 mm long dowels -- Work Area(2) Separate working fields with (4) pneumatic top clamps can process up to (2) parts independently on the left-hand, right-hand or center stops; work pieces can be loaded in (1) field while being machined in the other to allow fast production of varying parts. -- Operator Interface:PC Front-end with Homag Power Control PC 85T, WoodWOP 5.0 operating system with graphic programming & error messaging.17" TFT flat screen monitor, CD-RW drive, 1.44 MB floppy drive, standard keyboard & mouse; Software allows program design with automatic mirror-image by use of an active center stop located 600 mm (23.6") from zero. -- Complete with:All manuals, documentation provided with machine. -- Actual Model is HOMAG ABD 050.

HOMAG ABD-060/12/NA - CNC Bore, Glue & Dowel Inserter: -- Specifications(1) Horizontal drilling head with: (3) Independent spindles on 32 mm centers; Servo control of: "X", "Y" & "Z" Axes; (1) glue & dowel injector with glue flow control; (1) vibrating hopper dowel feeder. -- Working CapacityMaterial size: 20 mm - 1,250 mm (3/4" - 49") long; 50 mm - 800 mm (1.97" - 31-1/2") wide; 10 mm - 60 mm (0.4" - 2.4") thick.Machine is currently set up for: 8 mm Dia.; 30 or 35 mm long dowels (additional dowel sizes are optional). -- Work Area(2) Separate working fields with: (4) Pneumatic top clamps can process up to (4) parts independently on the left hand, right hand or center stops.Work can be loaded in: (1) Field while being machined in the other to allow fast production of varying parts. -- Operator InterfacePC Front-End with HOMAG - Power Control PC 85T; WoodWOP 5.0 Operating System with: Graphic programming & error messaging.17" TFT Flat screen monitor; CD-RW drive; 1.44 MB floppy drive; standard keyboard & mouse; software allows program design with automatic mirror image by use of an active center stop: Located 600 mm (23.6") from zero. -- Complete with: All manuals, documentation & program disk provided with machine. -- Actual Model: HOMAG ABD-060/12/NA

HOMAG - BHT 500: CNC Through-Feed Machining Center (2-Head) + BARGSTEADT Stacker -- SpecificationsHOMAG "BHT 500" CNC 2-Head Through-Feed PtP Machining Center: -- Working Capacity Single panel processing: "X" Axis 98.4" (2,500 mm); "Y" axis 55.4" (1,406 mm); "Z" axis 0.5" - "2.36" (12 - 60 mm) min./max. panel thickness.(2) Panel processing: "X" Axis 98.4" (2,500 mm); Y" Axis 23.6" + 23.6" (600 + 600 mm); 1/2" - "2.36" (12 - 60 mm) min./max. panel thickness. -- Positioning SpeedVertical boring unit(s) Positioning speed: "X" Axis 328 FPM (100 MPM); "Y" axis 230 FPM (70 MPM); "'Z" axis 82 FPM (25 MPM).Panel transfer belt variable feed speed from: 0 - 295 FPM (0 - 90 MPM). -- Horizontal Through-Feed Boring Units(2) 2 HP (1.5 kW) Motors (1-motor each side) with: Variable rotation speeds up to 9,000 RPM. (2) 19-Spindle LH units, (38) total LH spindles; (2) 19-spindle RH units, (38) total RH spindles; spindle are on 32 mm centers.LH Horizontal drilling support is fixed; RH support motorized & equipped with: LED Indicator for precision positioning, pneumatic locking, and individual adjustment for positioning according to the panel size. -- Horizontal PTP Boring UnitsCNC Controlled horizontal PtP boring units with: (2 + 2) spindles in the "Y" axis on each boring head; (8) "Y" axis spindles total) -- Vertical PTP Boring Units(2) 4 HP (3 kW) Motors (1-motor each head) with: Variable rotation speed; up to 9,000 RPM.(2) Independently controlled top mounted CNC PtP boring/grooving heads; each head with: (30) Independent vertical spindles; spindle are on 32 mm centers. -- Grooving Saws(2) 2 HP (1.5 kW) Motors (1-motor each head); "X" axis grooving saw with: Variable rotation speed up to 12,000 RPM & 100 mm dia. blade. -- Operator InterfaceIPC with: HOMAG "Power Control 85T" + WoodWOP + Windows "XP" Operating System; icon driven software with: Graphical interface allows Operator to quickly & efficiently create programs & diagnose malfunctions in simple terminology. 17" TFT Color monitor; multitask Operating System; input/output modules; axes override; 4-axis interpolation; diagnostic graphics aide for programming; machine data & tool management. -- Options Include: BARGSTEADT - "TBH 250/QL/25/12": Vacuum Stacker Device.Work cap. "X" Axis 98.4" (2,500 mm), "Y" axis 55" (1,400 mm), 2.3" (60 mm) Max. panel thickness.High-speed workpiece stack exchange with a cycle time of 35 seconds; thin work piece device for panels from 8 mm thick. -- Actual Model is HOMAG BHT 500

HOMAG - OPTIMAT BOF 211/30/R: Flat Table Machine (W/ATC/Boring/"C"Axis) -- Specifications4' x 10' Flat Matrix grid Phenolic working table. -- Working Field"X" Axis 120" (3.050 mm); "Y" axis 51" (1,300 mm); "Z" axis stroke 21" (535 mm); max material thickness 8.2" (210 mm). -- Positioning Speed"X" & "Y" Axis is 260 FPM (80 MPM); "Z" axis is 98 FPM (30 MPM). -- Boring Unit4.2 HP (3 kW) Variable speed from 1,500 - 7,500 RPM; (12) independent vertical spindles: (6) in "X" axis & (6) in "Y" axis. -- Machining(1) 19.4 HP (14.5 kW) Liquid-Cooled electrospindle router with: HSK 63F Adaptor; variable speed from 1,000 - 24,000 RPM. -- (1) NC Controlled C-axis for 360° horizontal processing. -- (1) 12-Positon automatic tool changer mounted at the back of the head for "on the fly" ATC. -- Operator Interface PC Front-End with: "HOMATIC" PC 85 Power Control + Windows "NT" + WoodWOP Operating System. -- 14" Color graphic monitor; industrial keyboard for data entry; 1.44 MB & CD RW disk drives; EtherNET interface for possible LAN connection to office PC. -- USB & RS-232 Serial interface for simple PC connection. -- NUM (PLC) With 3D Linear interpolation; 4-axis control for "X", "Y", "Z", & "C" axes. -- All mounted in separate free-standing control cabinet. -- Complete with:(1) 40 HP DEKKER "VMX055" Vacuum Pump; safety fencing; safety mats (will stop machine if operator enters work area); handheld pendent control. -- Actual Model: HOMAG OPTIMAT BOF 211/30/R

HOMAG VANTAGE 12L (BOF 311) 5'x12' CNC Router w/C-axis -- Specifications:• Table sizes: Vantage 12L,145.6" x 61" (3.700 x 1.550 mm)• Aluminum grid table• Main Router Power: 20 HP (14.9 kW)• Spindle Speed: Variable up to 24,000 RPM• Spindle Taper: HSK-F63 quick-change system.• Axes Capability: 3-axis• C-axis capabilities for aggregate clamping (4-axis functionality).• Aggregate Interface: Compatible with specialized HOMAG units, including the Flex5 5-axis aggregate• 10-position rotary/disc for ATC, mounted to the gantry• Drilling unit with 17 vertical and 4 horizontal drills• Drilling speed max: 7,500 RPM.• Homatic Power Control PC85• integrated with HOMAG's woodWOP software for programming• woodWOP with additional software for Nesting and engravings• Vacuum pump(s) with production capacity 500 m³/Hr• Safety cage/devices to minimize access to machine and vacuum pump.

HOUFEK - Maxx 1100: 2-Head Wide belt Sander43 Width cap.; Drum; Combination head.Head Configuration1st Head: Contact roll.2nd Head: Combination contact roll and finishing platen.Specifications -- 1st Head: 6" Dia. rubber-covered contact roll; 25 HP motor. -- 2nd Head: Combination head with: Rubber-covered contact roll; 6" dia.; air cushioned finishing platen; timers control platen inflation& deflation; 20 HP motor. -- 43" x 75" Abrasive belts. -- TRU-TRAK Solid-state belt tracking. -- Variable feed speed with inverter control; 15 - 45 FPM. -- 1 HP Motor; endless belt conveyor with: Automatic tracking. Equipped with & Features -- Motorized part thickness opening with: LED 0" - 6" Opening. -- Infeed & Outfeed rubber-covered holddown rolls. -- Infeed over thickness bar. -- Emergency stops at infeed & outfeed. -- Air-operated disc brakes on sanding heads. -- Electrical interlocks on: Main access doors; motor load meters.NOTE from Seller: This machine was damaged during transport by the straps going over the machine. Doors work fine; they have dents on the top where the straps dented them. - Price REDUCED to reflect this (cosmetic) damage.

LAHARCO LAS-C026 Diode LaserEconomical self-contained Visable Diode Laser, optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° to +40° C operating temperature, 90 V for 250 nano-sec surge protection. Beam angle 5 to 90 degrees, 5mW to 35mW output, 636 nm wave length for lines up to 20' projection. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed. -- Optional items consist of: Crossbar style mounting bracket,

LANCASTER - 1861-B: Clamp Assembly 2-Way Two-Way Frame Clamping machineSpecifications -- Motorized open/close of main jaws via 1/2 HP motor. -- Max. clamping capacity: 52" Tall x 56" W; minimum: 15" Tall x 11" W. -- (1) 6" Bore; 2" stroke pneumatic cylinders for main jaw clamp.2) 4" Bore; 2" stroke pneumatic cylinders for auxiliary jaws. -- Push button controls for: Open/close and cycle. Control valves on each cylinder for operator control. -- Clamp mounted on: 30° Angle with: Clamp assembly mounted. -- Jaws: Precision machined cast iron.

LANGE MASCHINEN BAU B85K Edgebanding MachineSpecifications: -- Workpiece thickness: 8 – 50 mmWorkpiece width min.: approx. 75 mmWorkpiece length min.: approx. 120 mmEdging thickness: 0,4 – 3,0 mmMax edge thickness = Workpiece thickness + 4mm (2+2)One sided automatic edge banding machine with direct glue application to straight workpieces, high frequency cut off station, high frequency top and bottom milling unit, chain feed, double roller top pressure and work piece support. For ABS,PVC, melamine and strong wood veneer roll materials as well as fixed lengths.

LANTECH Q-300 Semi-Automatic Low Profile Stretch WrapperSpecifications -- Variable control wrap force; power pre-stretch system (up to 200% standard). -- Film capacity from: 10"; to 20"; Width. -- Max. speed: 25 to 35 Loads per hour. -- Max. load dia.: 72";. -- Max. load height: 80";. Includes -- Ramp for hand pallet jack to drop pallet on 65"; dia. turntable.

LARICK 120 Single Spindle Profile Sander;Sands raised panels, and door edges.Specifications: -- 1" Dia. x 4" long belt driven arbor; 700 - 1700 RPM variable speed, 1 HP motor. Arbor is vertically adjustable. -- Complete with: 25" x 22" butcherblock maple table, enclosed fabricated steel base and large hand wheels for easy spindle adjustment. -- Includes: Sensing safety guard for anti-automatic restart protection.

Single head; 1 HP Belt drive motor, Fixed spindle, Mechanical controlled variable speed from 700 - 1,700 RPM, 4" vertical spindle adjustment. -- Features: 27" x 25" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust port, large hand wheels for easy spindle adjustment.