Equipment For Sale

ASSORTED MOTORS, IN ALL HP & SPEEDS AVAILABLE. Chipper and band mill motors 400HP, US, 585 RPM, DRIP, FRAME 1689S. TOSHIBA 200 HP at 1200 RPM. General Electric 300 HP, 514 RPM, 460 Volt for direct connect, Old style GE frame 17A's and 17B's to redesign up to 500 HP @ 450 RPM. 300HP ALLIS CHALMERS MOTOR 514 RPM, DRIP, 30KS8 FRAME. Many other sizes available CALL FOR YOUR SPECIFIC NEED. From 10HP to 600HP. See gear reducers with various HPs and ratios (see Gear Reducer listings).

2021 Toyota 7FBCU45 Cushion Tire Forklift with 6,068 hours. Electric power, rightline Sideshifting Fork Positioner, Enclosed Cab, Overhead Guard and Load Backrest. Fork length 48", Lowered Ht. 93", Max Ht. 187, Free Lift 44". 80% tread remaining on tires. Weight 13,831lb Length 8.63ft in Width 4.43ft in Height 7.52ft in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Trace Machine Pallet 4 Stringer Nailer w/Stacker & 56in X 11ft 6in Pallet Rollout

Self-propelled track carrier Self-powered slasher Radio remote control No hydraulics or electrics Reguired

Trackside Mfg Stretch Wrapping Machine 31"x10' infeed and outfeed, 24" belt, no power

1988 Trail Mobile Flatbed 48' Spread axle Rebuilt frame New air ride New hardwood deck Lights good Brakes good Aluminum rims Low pro 22.5 tires (need replaced soon)

2012 Transcraft 48' aluminum flatbed trailer w/air ride VIN 1TTF-482C9D3756763

53' Step Deck Aluminum top steel frame Tires are 40% Brakes are 50% Seller Upgraded Still In Use

2009/2010 53' x 102" Transcraft Conestoga (Curtain Side)Flatbed VIN# 1TT F532S x A 1088115 Merlott Vango Tarp.

2011 TRANSPORT 5 AXLE LOG PUP AIR RIDE SUPER SINGLES ALUMINUM STAKES 24' DECK

40 HP TRAVAINI Liquid Ring, Single-stage Vacuum pump. Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. Pump materials include cast iron housing, ductile iron impeller and stain less steel shaft. Shaft seals are carbon face with Viton elastomers. BALDOR 40 HP, 230/460 Volt, 3-Phase, 60 Hz, TEFC direct drive motor assembly. Sealing fluid re-circulating system includes reservoir of carbon steel with fluid level gauge and drain, high efficiency discharge separator and over sized heat exchanger. High temp switch to protect against over-temp operation. Suction line accessories include inlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve and vacuum relief valve. Heat exchanger is air cooler type made from aluminum and extended surface fins. Electrical controls include: Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet. The amps @ 230 Volt = 104; the amps @ 460 Volt = 52 amps.

Tree 2UVR Vertical Milling Machine Incudes Elephant Vise Good Condition

1988 Trelan Model 18 Whole Tree Chipper Equipped with Detroit 518 Diesel Engine, Engine Hours Unknown, New Drive Chain and New Belt, New Tire, No Separator Ready for the Woods... Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2005 Trelan 23RC Whole Tree Chipper, 3 knife, Cat V12 with 5,000 hours, New clutch and disk bearings. Works as it should. Approximately 5k hours makes a beautiful chip. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 Trelan 23 -No blow by and doesn't use oil -New hood jack -New cylinder -10 sets of new blades -Extra set of belts -Disk pockets are in good shape

1989 Trelan 23 Chipper -9000 frame hours -Rebuilt C-27 CAT with 200 hours on engine -New tires -New outrigger piston -Rewired corded remote -New wireless remote -New hoses -New intakes -New bearings in the PTO -Engine Preheater -New Auto-feed system NEEDS PAINT BUT WILL GO STRAIGHT TO WORK!!!

TREMZAC 248-TR-CO Portable Shaving MillPower supply; 65 HP from P.T.O. of tractor at 540 RPM (not included ). -- Emergency shutdown included. -- Log; 5" to 22" in diameter x 96" long. -- Capacity ( shaving ) 5 to 19 cubic yards/hour. -- Hopper Magazine; 24" wide x 96" long. -- Double Axle Trailer with hydraulic brake included. -- Cutter head 24" with (8) knives -- Dimensions; 7' 3"' wide x 31' 3" long.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Custom Ceiling / Flooring Table Table Size: 32' x 6'9" to 14'3" Table Operated by Both Push Button and Key Fob Controls Floor can be built manually on the table Clamping Stud Locators at 16" & 24"

TRK Shear Head, 80 mm pins, 500 hours, $16,000