Equipment For Sale

CANTEK RAPIDEDGE PRO EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness: 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Premill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counter rotating cutte rheads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot designed for EVA hot melt glue. Glue Pot: Quick-Change type; can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with: (2) Pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure Rollers Section consists of: (1) Large driven roller, followed by a smaller one. Workstations: -- End Trim(1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with: (2) Saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:RAPID adjustment system uses Pneumatic 3-position adjustment to quickly change from 0.5 mm - 1 mm; 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM: High frequency motors for: Top & Bottom trimming of the panel; each motor has an inset knife cutterhead that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding(1) 1/2 HP (0.37 kW) - 12,000 RPM: High frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm - 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile ScrappersMulti-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat ScrappersFlat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units(2) 0.2 HP (0.12 kW) - 3,000 RPM motors; Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. -- Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Pre-Milling Station so any overspray that gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface of the panel. -- Operator

CANTEK C10RSStraight Line Rip Saw --Specifications -- 12" Over cutting Rip Saw ruggedly constructed with cast iron & ground tables, -- Cast iron pressure housing with (6) guide rollers and solid welded steel base chassis -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", -- Feedspeeds of 50, 65 and 85 FPM - 4,500 RPM, --10 HPsaw arbor motor; 1 HP feed motor, --Min. workpiece length 8", max. cutting thickness 3-3/8", --13 3/4" distance between saw and column, -- 30" X 50" table size, 31-1/2" table height. --Equipped with & Features: -- Cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- (1)-piece cast iron chain with a diamond cut surface for positive material feeding. --Included: Manual , and several blades and the toolkit.÷

CANTEK C-12RSH Overcutting Straight Line Rip Saw;Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (8) holddown rollers and solid welded steel base chassis.Specifications: -- 3.35" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 15 HP arbor motor; swings 8" thru 12" dia. blade at 4,500 RPM; with 18" distance from blade to saw column. -- Arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V Belt driven from below. -- 31-7/8" From floor to top of table; table is 39" wide x 57" long. -- Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Feed & Chain: -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding and absolute straight line feeding. -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. -- Equipped with high-frequency hardened chain Guide Rails. -- The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows).Features: -- Easy to access adjustments and controls. -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. -- Equipped with: (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- (1) 5" dia. dust outlet. -- Soft start, Star Delta starter - Telemechanique-Square D, Magnetic Wye/Delta Starters - Low Amperage Soft-Starter on the arbor motor - Electrics to UL/CSA Standards.Available Options when order with machine: --20mW Laser (FPIMLC1320W) & Laser Holder (FPICAN03) – made in N.A.... $ 495.00 -- KANEFUSA 12" Glue Joint Carbide Rip Saw Blade...$ 165.00

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

Cargo C12 Winch for Case 310 Dozer, $2,500

Carco PA 90 Winch with Fairlead for CAT D7E or on JD 850J & K

Carco Winch for JD 750J & K’s, $7500

Cardinal Gang Rip Saw 6" Double Arbor Infeed 3-Rolls on top, 3-rolls on bottom (2) 125 HP Motors

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large-diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents the backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self-centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus unwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

CARLSON CD PINNER PLUS Cabinet Door Clamp & Pinner; 30" Wide x 48" High max. Capability. The ProMax Cabinet Door Pinner is an affordable system that squares, clamps and fastens a variety of cabinet door styles and sizes. This machine is designed to handle stile widths between 1-1/4" and 3-1/2" in 1/8" increments and any rail widths. Standard product minimum: approximately 7" wide X 6" tall for 2" stile and rail cabinet doors. Standard product maximum: approximately 30" wide X 60" tall for 2" stile and rail cabinet doors.General Specifications: -- Standard joy stick operation allows quick and accurate size adjustments. -- The frame is ergonomically designed at an angle for easy placement of sub-assembled door parts and fast removal of the finished product. -- Operating controls are simple and convenient to minimize training time. -- Machine functions are air powered with programmable electrical controls for accurate and reliable operation.Includes: -- Air motor drive system. -- Standard clamp pads. -- Cope & Stick door fastening. -- Spare tool assembly. -- Size upgrade - Height 60". -- Miter capability. -- Safety light curtain. Features: -- Heavy duty frame, low maintenance, powered size adjustments, precision linear bearings, overhead mar-proof clamping, programmable controller.

2022 Carlton 2015 Tree Chipper, Deere 140HP Diesel, Hydraulic Winch.

2015 Carlton SP7015 Stump Grinder with 1,400 hours. 66HP Kabota Diesel Engine, Blade, remote, 4 x 4 with a trailer. Weight 3500 Lbs. Length 10’ 6” Height 52” Width 35” Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

CAROLINA BULK BAG FILLING MACHINECarolina Conveying filling stations are used to safely and efficiently load bulk bags. A filling head with an inflatable seal is used for dust-tight loading of the bulk bag, and bolts to the adjustable height framework. The inlet to the filling head is connected to the customer’s equipment above via a flexible tube. The bag spout is secured to the outlet with an inflatable seal. The seal inflation is controlled by a manual on/off spool valve, which pipes air to the unit. A cavity around the outerperimeter allows displaced air and dust to exit the filling head through a dust extraction nozzleSpecifications & Features: -- Rated for 5,000 Lbs, Bag fill up to 4000 Lbs. -- Platform size 48" x 48" -- Bulk Bag Filler Stations are used to safely and efficiently load bulk bags. -- A filling head with an inflatable seal is used for dust-tight loading of the bulk bag, and bolts to the adjustable framework height. -- The inlet to the filling head is connected to the customer's equipment above via a flexible tube. -- The bag spout is secured to the outlet with an inflatable seal. -- The seal inflation is controlled by a manual on/off spool valve, which pipes air to the unit. -- A cavity around the outer perimeter allows displaced air and dust to exit the filling head through a dust extraction nozzle. -- Support frame with adjustable rack. -- Support arms; Four adjustable height arms for loop-type bags. -- Inlet 8" round flange, ASA 150 Bolt hole pattern. -- Inflatable seal; White seamless gum rubber tube. -- Dust spigot 3" o.d. tube - 71 -- Weight platform with Digital Scale - 84 -- Output for digital readout is included - 7185

CAROLINA BLOWER Size 80-6 Material Handling Fan with Motor. --Specification: -- Can handle approx 35,000 CFM @ 11" SP and 840 RPM. -- Comes with: Westinghouse Life-Line (high efficiency) 125 HP, 405T frame, ODP Motor complete with pulleys.. -- Motor is not mounted on base. -- Actual Model is 80-6SD.

Carolina Blower Model 506HD S/N B11225

CAROLINA BLOWER 45-6 Standard Duty Fan/Motor package assembled complete 30 HP motor. -- Rated at 8,860 CFM at 10" SP. Fan inlet diameter is 19". -- Fabricated with 3/8" thick wheel blades, 1/4" thick housing, primed and painted beige. 30 HP TEFC motor. Unitary base, V-belt drives, shaft, and belt safety guards. -- This is an Industrial Material Handling fan with paddle-wheel construction. Also available in Heavy Duty version at extra cost, with thicker scroll-housing to handle airborne smaller solid wood or similar material.

Carolina Blower Dust Collector Dust Blower 19" Pipe 75HP Motor (Est)

24 wide x 24 long,